TY  - CONF
AU  - Gulicovski, Jelena
AU  - Nenadović, Miloš
AU  - Mirković, Miljana
AU  - Kljajević, Ljiljana
AU  - Bošković, Ivana
AU  - Vukčević, Marija
AU  - Nenadović, Snežana
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/11752
AB  - Due to the low CO2 emission of geopolymers compared to Portland cement, interest in their use as binding cement has increased in recent years. The main goal of this research is to relate the green and sustainable characteristics to the good mechanical and chemical properties of fly ashbased geopolymers. For those purposes, samples of different ratios of fly ash (FA) and metakaolin (MK) were prepared. Mineralogical characterization of the geopolymer samples conducted using X-ray powder diffraction (XRD) showed that in the geopolymer synthesis reaction new amorphous phase was formed. Diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) confirmed characteristic bands of Si-O and O-Si-O groups at 1045 cm–1 . Compressive strength analysis revealed that the optimal ratio of FA and MK is 50:50 and exhibits the highest value, while X-ray photoelectron spectroscopy (XPS) analysis revealed the total reduction of carbon content in the alkali activated geopolymer with optimal stoichiometry 50:50. The results of this research indicates the possibility to obtain a geopolymer material with almost complete absence of carbon, which implies further application as a material with very high environmental potential and zero carbon emission.
PB  - Society of Chemists and Technologists of Macedonia
C3  - 26th Congress of the Society of Chemists and Technologists of Macedonia : the book of abstracts; September 20-23, Ohrid, Macedonia
T1  - Preparation and Performance of Low Content Carbon Geopolymer
SP  - 24
EP  - 24
UR  - https://hdl.handle.net/21.15107/rcub_vinar_11752
ER  - 

@conference{
author = "Gulicovski, Jelena and Nenadović, Miloš and Mirković, Miljana and Kljajević, Ljiljana and Bošković, Ivana and Vukčević, Marija and Nenadović, Snežana",
year = "2023",
abstract = "Due to the low CO2 emission of geopolymers compared to Portland cement, interest in their use as binding cement has increased in recent years. The main goal of this research is to relate the green and sustainable characteristics to the good mechanical and chemical properties of fly ashbased geopolymers. For those purposes, samples of different ratios of fly ash (FA) and metakaolin (MK) were prepared. Mineralogical characterization of the geopolymer samples conducted using X-ray powder diffraction (XRD) showed that in the geopolymer synthesis reaction new amorphous phase was formed. Diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) confirmed characteristic bands of Si-O and O-Si-O groups at 1045 cm–1 . Compressive strength analysis revealed that the optimal ratio of FA and MK is 50:50 and exhibits the highest value, while X-ray photoelectron spectroscopy (XPS) analysis revealed the total reduction of carbon content in the alkali activated geopolymer with optimal stoichiometry 50:50. The results of this research indicates the possibility to obtain a geopolymer material with almost complete absence of carbon, which implies further application as a material with very high environmental potential and zero carbon emission.",
publisher = "Society of Chemists and Technologists of Macedonia",
journal = "26th Congress of the Society of Chemists and Technologists of Macedonia : the book of abstracts; September 20-23, Ohrid, Macedonia",
title = "Preparation and Performance of Low Content Carbon Geopolymer",
pages = "24-24",
url = "https://hdl.handle.net/21.15107/rcub_vinar_11752"
}

Gulicovski, J., Nenadović, M., Mirković, M., Kljajević, L., Bošković, I., Vukčević, M.,& Nenadović, S.. (2023). Preparation and Performance of Low Content Carbon Geopolymer. in 26th Congress of the Society of Chemists and Technologists of Macedonia : the book of abstracts; September 20-23, Ohrid, Macedonia
Society of Chemists and Technologists of Macedonia., 24-24.
https://hdl.handle.net/21.15107/rcub_vinar_11752

Gulicovski J, Nenadović M, Mirković M, Kljajević L, Bošković I, Vukčević M, Nenadović S. Preparation and Performance of Low Content Carbon Geopolymer. in 26th Congress of the Society of Chemists and Technologists of Macedonia : the book of abstracts; September 20-23, Ohrid, Macedonia. 2023;:24-24.
https://hdl.handle.net/21.15107/rcub_vinar_11752 .

Gulicovski, Jelena, Nenadović, Miloš, Mirković, Miljana, Kljajević, Ljiljana, Bošković, Ivana, Vukčević, Marija, Nenadović, Snežana, "Preparation and Performance of Low Content Carbon Geopolymer" in 26th Congress of the Society of Chemists and Technologists of Macedonia : the book of abstracts; September 20-23, Ohrid, Macedonia (2023):24-24,
https://hdl.handle.net/21.15107/rcub_vinar_11752 .

TY  - JOUR
AU  - Maletić, Marina
AU  - Kalijadis, Ana
AU  - Lazović, Vladimir
AU  - Trifunović, Snežana
AU  - Babić, Biljana M.
AU  - Dapčević, Aleksandra
AU  - Kovač, Janez
AU  - Vukčević, Marija
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10693
AB  - N-doped TiO2/carbon composites (TiO2/CN) with different nitrogen content, were obtained starting from titanium isopropoxide and glucose, and by varying the amount of melamine, added to starting reaction mixture. For comparison, an undoped sample (TiO2/C) was also prepared. Structural and surface characteristics were determined through scanning electron microscopy, thermogravimetric analysis, elemental analysis, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and nitrogen adsorption–desorption isotherms. The photocatalytic activity of TiO2/CN composites was examined via photocatalytic degradation of methylene blue and multiclass pharmaceuticals from water solution. It was found that N doping of TiO2/carbon composites induced changes in structural and surface characteristics of TiO2/CN composites, improving their adsorption, but decreasing photocatalytic efficiency. Nevertheless, TiO2/CN0.05 composite obtained by the hydrothermal synthesis in the presence of glucose and 0.05 g melamine showed the highest efficiency for removing selected pharmaceuticals and methylene blue from aqueous solutions through the combined processes of adsorption in the dark, and photocatalytic degradation under UV and visible irradiation.
T2  - Journal of the Serbian Chemical Society
T1  - Influence of N doping on structural and photocatalytic properties of hydrothermally synthesized TiO2/carbon composites
VL  - 88
IS  - 2
SP  - 183
EP  - 197
DO  - 10.2298/JSC220608079M
ER  - 

@article{
author = "Maletić, Marina and Kalijadis, Ana and Lazović, Vladimir and Trifunović, Snežana and Babić, Biljana M. and Dapčević, Aleksandra and Kovač, Janez and Vukčević, Marija",
year = "2023",
abstract = "N-doped TiO2/carbon composites (TiO2/CN) with different nitrogen content, were obtained starting from titanium isopropoxide and glucose, and by varying the amount of melamine, added to starting reaction mixture. For comparison, an undoped sample (TiO2/C) was also prepared. Structural and surface characteristics were determined through scanning electron microscopy, thermogravimetric analysis, elemental analysis, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and nitrogen adsorption–desorption isotherms. The photocatalytic activity of TiO2/CN composites was examined via photocatalytic degradation of methylene blue and multiclass pharmaceuticals from water solution. It was found that N doping of TiO2/carbon composites induced changes in structural and surface characteristics of TiO2/CN composites, improving their adsorption, but decreasing photocatalytic efficiency. Nevertheless, TiO2/CN0.05 composite obtained by the hydrothermal synthesis in the presence of glucose and 0.05 g melamine showed the highest efficiency for removing selected pharmaceuticals and methylene blue from aqueous solutions through the combined processes of adsorption in the dark, and photocatalytic degradation under UV and visible irradiation.",
journal = "Journal of the Serbian Chemical Society",
title = "Influence of N doping on structural and photocatalytic properties of hydrothermally synthesized TiO2/carbon composites",
volume = "88",
number = "2",
pages = "183-197",
doi = "10.2298/JSC220608079M"
}

Maletić, M., Kalijadis, A., Lazović, V., Trifunović, S., Babić, B. M., Dapčević, A., Kovač, J.,& Vukčević, M.. (2023). Influence of N doping on structural and photocatalytic properties of hydrothermally synthesized TiO2/carbon composites. in Journal of the Serbian Chemical Society, 88(2), 183-197.
https://doi.org/10.2298/JSC220608079M

Maletić M, Kalijadis A, Lazović V, Trifunović S, Babić BM, Dapčević A, Kovač J, Vukčević M. Influence of N doping on structural and photocatalytic properties of hydrothermally synthesized TiO2/carbon composites. in Journal of the Serbian Chemical Society. 2023;88(2):183-197.
doi:10.2298/JSC220608079M .

Maletić, Marina, Kalijadis, Ana, Lazović, Vladimir, Trifunović, Snežana, Babić, Biljana M., Dapčević, Aleksandra, Kovač, Janez, Vukčević, Marija, "Influence of N doping on structural and photocatalytic properties of hydrothermally synthesized TiO2/carbon composites" in Journal of the Serbian Chemical Society, 88, no. 2 (2023):183-197,
https://doi.org/10.2298/JSC220608079M . .

TY  - JOUR
AU  - Vukčević, Marija M.
AU  - Maletić, Marina
AU  - Đurkić, Tatjana M.
AU  - Babić, Biljana M.
AU  - Kalijadis, Ana
PY  - 2022
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10223
AB  - Carbonaceous solid-phase extraction (SPE) sorbent, efficient in isolation and enrichment of multiclass pesticides and pharmaceuticals from water, was synthesized starting from cheap waste beech sawdust and using KOH as the activated agent. The first step in carbon material preparation was hydrothermal carbonization of the waste beech sawdust. Following hydrothermal treatment, the obtained material was activated, using different amounts of KOH. It was found that applied activation leads to changes in material structure, an increase in specific surface area, and a decrease in the number of surface oxygen groups compared to carbonized sample. SPE procedure of multiclass pesticides and pharmaceuticals from water using activated carbonized beech sawdust (AcSD) was optimized by selecting the appropriate elution solvents, the sample pH, and the sample volume to obtain the highest enrichment efficiency. The optimized SPE procedure was applied for water analysis using different AcSD samples as a sorbent for analyte preconcentration. Activated carbon sorbent, obtained with the highest amount of KOH, showed the highest recoveries regarding the most analytes, which were comparable with the recoveries obtained by commercial cartridges. © 2022 Serbian Chemical Society. All rights reserved.
T2  - Journal of the Serbian Chemical Society
T1  - Beech sawdust based adsorbents for solid-phase extraction of pesticides and pharmaceuticals
VL  - 87
IS  - 2
SP  - 205
EP  - 217
DO  - 10.2298/JSC210614051V
ER  - 

@article{
author = "Vukčević, Marija M. and Maletić, Marina and Đurkić, Tatjana M. and Babić, Biljana M. and Kalijadis, Ana",
year = "2022",
abstract = "Carbonaceous solid-phase extraction (SPE) sorbent, efficient in isolation and enrichment of multiclass pesticides and pharmaceuticals from water, was synthesized starting from cheap waste beech sawdust and using KOH as the activated agent. The first step in carbon material preparation was hydrothermal carbonization of the waste beech sawdust. Following hydrothermal treatment, the obtained material was activated, using different amounts of KOH. It was found that applied activation leads to changes in material structure, an increase in specific surface area, and a decrease in the number of surface oxygen groups compared to carbonized sample. SPE procedure of multiclass pesticides and pharmaceuticals from water using activated carbonized beech sawdust (AcSD) was optimized by selecting the appropriate elution solvents, the sample pH, and the sample volume to obtain the highest enrichment efficiency. The optimized SPE procedure was applied for water analysis using different AcSD samples as a sorbent for analyte preconcentration. Activated carbon sorbent, obtained with the highest amount of KOH, showed the highest recoveries regarding the most analytes, which were comparable with the recoveries obtained by commercial cartridges. © 2022 Serbian Chemical Society. All rights reserved.",
journal = "Journal of the Serbian Chemical Society",
title = "Beech sawdust based adsorbents for solid-phase extraction of pesticides and pharmaceuticals",
volume = "87",
number = "2",
pages = "205-217",
doi = "10.2298/JSC210614051V"
}

Vukčević, M. M., Maletić, M., Đurkić, T. M., Babić, B. M.,& Kalijadis, A.. (2022). Beech sawdust based adsorbents for solid-phase extraction of pesticides and pharmaceuticals. in Journal of the Serbian Chemical Society, 87(2), 205-217.
https://doi.org/10.2298/JSC210614051V

Vukčević MM, Maletić M, Đurkić TM, Babić BM, Kalijadis A. Beech sawdust based adsorbents for solid-phase extraction of pesticides and pharmaceuticals. in Journal of the Serbian Chemical Society. 2022;87(2):205-217.
doi:10.2298/JSC210614051V .

Vukčević, Marija M., Maletić, Marina, Đurkić, Tatjana M., Babić, Biljana M., Kalijadis, Ana, "Beech sawdust based adsorbents for solid-phase extraction of pesticides and pharmaceuticals" in Journal of the Serbian Chemical Society, 87, no. 2 (2022):205-217,
https://doi.org/10.2298/JSC210614051V . .

TY  - JOUR
AU  - Kalijadis, Ana
AU  - Maletić, Marina M.
AU  - Bjelajac, Anđelika Z.
AU  - Babić, Biljana M.
AU  - Minović-Arsić, Tamara
AU  - Vukčević, Marija M.
PY  - 2022
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10339
AB  - In this study, the influence of boron doping on structural and surface properties of carbon material synthesized by a hydrothermal method was investigated, and the obtained results were compared with the previously published influence that boron has on characteristics of carbonized boron-doped hydrothermal carbons (CHTCB). Hydrothermal carbons doped with boron (HTCB) were obtained by the hydrothermal synthesis of glucose solutions with different nominal concentrations of boric acid. It was found that glucose based hydrothermal carbon does not have developed porosity, and the presence of boron in their structure has insignificant influence on it. On the contrary, additional carbonization increases the specific surface area of the undoped sample, while an increase in boron content drastically decreases the specific surface area. Boron doping leads to a decrease in the amount of surface oxygen groups, for both, hydrothermally synthesized and additionally carbonized materials. Raman analysis showed that the boron content does not affect a structural arrangement of the HTCB samples, and Raman structural parameters show a higher degree of disorder, compared to the CHTCB samples. Comparison of structural and surface characteristics of hydrothermal carbons and carbonized materials contributes to the study of the so far, insufficiently clarified influence that boron incorporation has on the material characteristics. © 2022 Serbian Chemical Society. All rights reserved.
T2  - Journal of the Serbian Chemical Society
T1  - Influence of boron doping on characteristics of glucose-based hydrothermal carbons
VL  - 87
IS  - 6
SP  - 749
EP  - 760
DO  - 10.2298/JSC211011001K
ER  - 

@article{
author = "Kalijadis, Ana and Maletić, Marina M. and Bjelajac, Anđelika Z. and Babić, Biljana M. and Minović-Arsić, Tamara and Vukčević, Marija M.",
year = "2022",
abstract = "In this study, the influence of boron doping on structural and surface properties of carbon material synthesized by a hydrothermal method was investigated, and the obtained results were compared with the previously published influence that boron has on characteristics of carbonized boron-doped hydrothermal carbons (CHTCB). Hydrothermal carbons doped with boron (HTCB) were obtained by the hydrothermal synthesis of glucose solutions with different nominal concentrations of boric acid. It was found that glucose based hydrothermal carbon does not have developed porosity, and the presence of boron in their structure has insignificant influence on it. On the contrary, additional carbonization increases the specific surface area of the undoped sample, while an increase in boron content drastically decreases the specific surface area. Boron doping leads to a decrease in the amount of surface oxygen groups, for both, hydrothermally synthesized and additionally carbonized materials. Raman analysis showed that the boron content does not affect a structural arrangement of the HTCB samples, and Raman structural parameters show a higher degree of disorder, compared to the CHTCB samples. Comparison of structural and surface characteristics of hydrothermal carbons and carbonized materials contributes to the study of the so far, insufficiently clarified influence that boron incorporation has on the material characteristics. © 2022 Serbian Chemical Society. All rights reserved.",
journal = "Journal of the Serbian Chemical Society",
title = "Influence of boron doping on characteristics of glucose-based hydrothermal carbons",
volume = "87",
number = "6",
pages = "749-760",
doi = "10.2298/JSC211011001K"
}

Kalijadis, A., Maletić, M. M., Bjelajac, A. Z., Babić, B. M., Minović-Arsić, T.,& Vukčević, M. M.. (2022). Influence of boron doping on characteristics of glucose-based hydrothermal carbons. in Journal of the Serbian Chemical Society, 87(6), 749-760.
https://doi.org/10.2298/JSC211011001K

Kalijadis A, Maletić MM, Bjelajac AZ, Babić BM, Minović-Arsić T, Vukčević MM. Influence of boron doping on characteristics of glucose-based hydrothermal carbons. in Journal of the Serbian Chemical Society. 2022;87(6):749-760.
doi:10.2298/JSC211011001K .

Kalijadis, Ana, Maletić, Marina M., Bjelajac, Anđelika Z., Babić, Biljana M., Minović-Arsić, Tamara, Vukčević, Marija M., "Influence of boron doping on characteristics of glucose-based hydrothermal carbons" in Journal of the Serbian Chemical Society, 87, no. 6 (2022):749-760,
https://doi.org/10.2298/JSC211011001K . .

TY  - CONF
AU  - Prokić, Danijela
AU  - Vukčević, Marija
AU  - Maletić, Marina
AU  - Kalijadis, Ana
AU  - Babić, Biljana M.
AU  - Janković-Častvan, Ivona
AU  - Đurkić, Tatjana
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/11598
AB  - Za ekstrakciju estrogenih hormona (estrona, 17β-estradiola i 17α-etinilestradiola) iz vodenih rastvora metodom ekstrakcije na čvrstoj fazi, u ovom radu korišćen je ugljenični kriogel kao sorbent. Metoda ekstrakcije na čvrstoj fazi optimizovana je izborom odgovarajuće mase sorbenta, zapremine i početne pH vrednosti vodenog rastvora hormona, kao i odabirom organskog rastvarača za eluira-nje. Koncentracija ispitivanih hormona u rastvoru nakon ekstrakcije određivana je metodom tečne hromatografije visoke performance u sprezi sa tandem masenom spektrometrijom. Na osnovu prinosa ispitivanih hormona, dobijeni su optimalni parametri metode ekstrakcije na čvrstoj fazi za predkon-centrisanje hormona iz vodenog rastvora: ekstrakcija hormona iz 100 cm3 vodenog rastvora, početne pH vrednosti podešene na 7, vrši se na 20 mg sorpcionog materijala, a smeša dihlormetan/methanol koristi se kao organski rastvarač za eluiranje. Vrednosti prinosa, dobijenih pri optimalnim uslovima, iznosile su od 77 % za estron, do 86 % za 17β-estradiol, uz relativnu standardnu devijaciju od 7,4 do 18 %.
AB  - In this study, carbon cryogel was used as solid-phase extraction sorbent for the extraction of estrogenic hormones (estrone, 17β-estradiol, and 17α-ethinylestradiol) from water solution.
The solid-phase extraction (SPE) method was optimized by choosing an appropriate mass of the sorbent, volume, and initial pH of estrogenic hormone water solution, as well as by choosing an appropriate organic solvent. The concentration of tested hormones after extraction was measured by liquid
chromatography coupled with tandem mass spectrometry. Based on the obtained hormone recoveries, the following optimal conditions of the SPE procedure were chosen: 100 cm3
of hormone water
solution at initial pH adjusted to 7, 20 mg of the sorbent, the methanol-dichloromethane mixture was
used for hormone elution. Recoveries obtained under the optimal conditions ranged from 77 % for
estrone, to 86 % for 17β-estradiol, with relative standard deviation from 7,4 to 18 %.
PB  - Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije (SMEITS) : Društvo za procesnu tehniku
C3  - 34. Međunarodni kongres o procesnoj industriji - PROCESING ′21 : zbornik radova
T1  - Ekstrakcija estrogenih hormona iz vode korišćenjem ugljeničnog kriogela kao sorbenta
T1  - Extraction of estrogen hormones from water using
carbon cryogel as sorbent
SP  - 123
EP  - 127
DO  - 10.24094/ptk.021.34.1.123
ER  - 

@conference{
author = "Prokić, Danijela and Vukčević, Marija and Maletić, Marina and Kalijadis, Ana and Babić, Biljana M. and Janković-Častvan, Ivona and Đurkić, Tatjana",
year = "2021",
abstract = "Za ekstrakciju estrogenih hormona (estrona, 17β-estradiola i 17α-etinilestradiola) iz vodenih rastvora metodom ekstrakcije na čvrstoj fazi, u ovom radu korišćen je ugljenični kriogel kao sorbent. Metoda ekstrakcije na čvrstoj fazi optimizovana je izborom odgovarajuće mase sorbenta, zapremine i početne pH vrednosti vodenog rastvora hormona, kao i odabirom organskog rastvarača za eluira-nje. Koncentracija ispitivanih hormona u rastvoru nakon ekstrakcije određivana je metodom tečne hromatografije visoke performance u sprezi sa tandem masenom spektrometrijom. Na osnovu prinosa ispitivanih hormona, dobijeni su optimalni parametri metode ekstrakcije na čvrstoj fazi za predkon-centrisanje hormona iz vodenog rastvora: ekstrakcija hormona iz 100 cm3 vodenog rastvora, početne pH vrednosti podešene na 7, vrši se na 20 mg sorpcionog materijala, a smeša dihlormetan/methanol koristi se kao organski rastvarač za eluiranje. Vrednosti prinosa, dobijenih pri optimalnim uslovima, iznosile su od 77 % za estron, do 86 % za 17β-estradiol, uz relativnu standardnu devijaciju od 7,4 do 18 %., In this study, carbon cryogel was used as solid-phase extraction sorbent for the extraction of estrogenic hormones (estrone, 17β-estradiol, and 17α-ethinylestradiol) from water solution.
The solid-phase extraction (SPE) method was optimized by choosing an appropriate mass of the sorbent, volume, and initial pH of estrogenic hormone water solution, as well as by choosing an appropriate organic solvent. The concentration of tested hormones after extraction was measured by liquid
chromatography coupled with tandem mass spectrometry. Based on the obtained hormone recoveries, the following optimal conditions of the SPE procedure were chosen: 100 cm3
of hormone water
solution at initial pH adjusted to 7, 20 mg of the sorbent, the methanol-dichloromethane mixture was
used for hormone elution. Recoveries obtained under the optimal conditions ranged from 77 % for
estrone, to 86 % for 17β-estradiol, with relative standard deviation from 7,4 to 18 %.",
publisher = "Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije (SMEITS) : Društvo za procesnu tehniku",
journal = "34. Međunarodni kongres o procesnoj industriji - PROCESING ′21 : zbornik radova",
title = "Ekstrakcija estrogenih hormona iz vode korišćenjem ugljeničnog kriogela kao sorbenta, Extraction of estrogen hormones from water using
carbon cryogel as sorbent",
pages = "123-127",
doi = "10.24094/ptk.021.34.1.123"
}

Prokić, D., Vukčević, M., Maletić, M., Kalijadis, A., Babić, B. M., Janković-Častvan, I.,& Đurkić, T.. (2021). Ekstrakcija estrogenih hormona iz vode korišćenjem ugljeničnog kriogela kao sorbenta. in 34. Međunarodni kongres o procesnoj industriji - PROCESING ′21 : zbornik radova
Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije (SMEITS) : Društvo za procesnu tehniku., 123-127.
https://doi.org/10.24094/ptk.021.34.1.123

Prokić D, Vukčević M, Maletić M, Kalijadis A, Babić BM, Janković-Častvan I, Đurkić T. Ekstrakcija estrogenih hormona iz vode korišćenjem ugljeničnog kriogela kao sorbenta. in 34. Međunarodni kongres o procesnoj industriji - PROCESING ′21 : zbornik radova. 2021;:123-127.
doi:10.24094/ptk.021.34.1.123 .

Prokić, Danijela, Vukčević, Marija, Maletić, Marina, Kalijadis, Ana, Babić, Biljana M., Janković-Častvan, Ivona, Đurkić, Tatjana, "Ekstrakcija estrogenih hormona iz vode korišćenjem ugljeničnog kriogela kao sorbenta" in 34. Međunarodni kongres o procesnoj industriji - PROCESING ′21 : zbornik radova (2021):123-127,
https://doi.org/10.24094/ptk.021.34.1.123 . .

TY  - CONF
AU  - Vukčević, Marija
AU  - Maletić, Marina
AU  - Kalijadis, Ana
AU  - Babić, Biljana
AU  - Đurkić, Tatjana
AU  - Laušević, Mila
PY  - 2018
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/11032
AB  - Zagađenje vodenih tokova teškim metalima je jedan od najakutnijih ekoloških
problema današnjice. S obzirom na to da teški metali nisu biorazgradivi, oni se akumuliraju
u životnoj sredini i na taj način ulaze u lanac ishrane ljudi i životinja, pa kao veoma toksične
materije, mogu izazivati niz opasnih i često neizlečivih bolesti. Iz tog razloga, istraživači
godinama u nazad razvijaju nove i usavršavaju postojeće tehnike za prečišćavanje otpadnih
voda od ovih zagađujućih materija [1]. Za prečišćavanje vode zagađene teškim metalima
mogu se koristiti različite metode: hemijska precipitacija, elektrohemijski tretmani, filtracija,
reverzna osmoza, jonska izmena, membranski procesi, adsorpcija. Jedna od najčešće
korišćenih je adsorpcija, koja zbog mogućnosti regenerisanja adsorbenta, odgovarajućim
desorpcionim procesom, predstavlja veoma efektivnu i ekonomičnu metodu. Zahvaljujući
razvijenoj specifičnoj površini i poroznosti, kao i prisustvu funkcionalnih grupa na površini,
različiti ugljenični materijali pokazuju visoku efikasnost u uklanjanju teških metala iz
vode. Karbon kriogel (CC) predstavlja ugljenični materijal razvijene mezoporoznosti čije
se adsorpcione karakteristike mogu poboljšati optimizacijom i kontrolisanjem parametara
dobijanja. U ovom radu je ispitana mogućnost uklanjanja jona teških metala (Cd2+, Ni2+ i
Zn2+) iz vode, korišćenjem karbon kriogela i hemijski modifikovanog karbon kriogela.
Prvi korak u sintezi karbon kriogela je polikondenzacija rezorcinola i formaldehida,
u prisustvu natrijum-karbonata kao katalizatora. Organski kriogel pripremljen je solgel tehnologijom uz naknadno sušenje postupkom zamrzavanja, dok je karbonizacija
organskog kriogela vršena u inertnoj atmosferi argona na temperaturi od 800 o
C [2]. U
cilju poboljšanja adsorpcionih karakteristika karbon kriogela, izvršeno je hemijsko
modifikovanje korišćenjem 5 M HNO3
. Karakterizacija materijala izvršena je merenjem
specifične površine BET metodom, određivanjem tačke nultog naelektrisanja metodom
masene titracije, kao i određivanjem vrsta funkcionalnih grupa prisutnih na površini
materijala, metodom infracrvene spektroskopije sa Furijeovom transformacijom (FTIR).
Ispitan je uticaj pH vrednosti rastvora, početne koncentracije jona metala u rastvoru, kao i
vremena kontakta na adsorpciju teških metala uzorcima karbon kriogela.Primenjenom hemijskom modifikacijom karbon kriogela ne dolazi do bitnijih
promena u specifičnoj površini i poroznosti materijala. S druge strane, ovim postupkom
dolazi do izmene površinske hemije materijala, uvođenjem novih, i povećanjem broja
postojećih kiselih površinskih grupa, što je pokazano FTIR analizom i smanjenjem
vrednosti tačke nultog naelektrisanja sa pHPZC = 9,3 na pHPZC = 3,1. Adsorpcija jona teških
metala na modifikovanom i nemodifikovanom karbon kriogelu vršena je na pH = 6, jer pri
ovoj pH vrednosti materijali pokazuju najveći adsorpcioni kapacitet, a ujedno je izborom
ove pH izbegnuta precipitacija hidroksida metala. Izmene u hemiji površine dovode i do
izmena adsorpcionih karakteristika karbon kriogela. Kako površinske grupe predstavljaju
aktivna mesta za adsorpciju jona teških metala, povećanje količine površinskih grupa kod
modifikovanog karbon kriogela dovodi do višestrukog povećanja adsorpcionog kapaciteta.
PB  - Belgrade : Serbian Chemical Society
C3  - ENVIROCHEM 2018 : 8th Symposium Chemistry and Environmental Protection : program and the book of abstracts
T1  - Karbon kriogel kao adsorbent za uklanjanje Cd(II), Zn(II) i Ni(II) jona iz vode
T1  - Carbon cryogel as an adsorbent for removal of Cd(II), Zn(II) and Ni(II) ions from water
SP  - 85
EP  - 86
UR  - https://hdl.handle.net/21.15107/rcub_vinar_11032
ER  - 

@conference{
author = "Vukčević, Marija and Maletić, Marina and Kalijadis, Ana and Babić, Biljana and Đurkić, Tatjana and Laušević, Mila",
year = "2018",
abstract = "Zagađenje vodenih tokova teškim metalima je jedan od najakutnijih ekoloških
problema današnjice. S obzirom na to da teški metali nisu biorazgradivi, oni se akumuliraju
u životnoj sredini i na taj način ulaze u lanac ishrane ljudi i životinja, pa kao veoma toksične
materije, mogu izazivati niz opasnih i često neizlečivih bolesti. Iz tog razloga, istraživači
godinama u nazad razvijaju nove i usavršavaju postojeće tehnike za prečišćavanje otpadnih
voda od ovih zagađujućih materija [1]. Za prečišćavanje vode zagađene teškim metalima
mogu se koristiti različite metode: hemijska precipitacija, elektrohemijski tretmani, filtracija,
reverzna osmoza, jonska izmena, membranski procesi, adsorpcija. Jedna od najčešće
korišćenih je adsorpcija, koja zbog mogućnosti regenerisanja adsorbenta, odgovarajućim
desorpcionim procesom, predstavlja veoma efektivnu i ekonomičnu metodu. Zahvaljujući
razvijenoj specifičnoj površini i poroznosti, kao i prisustvu funkcionalnih grupa na površini,
različiti ugljenični materijali pokazuju visoku efikasnost u uklanjanju teških metala iz
vode. Karbon kriogel (CC) predstavlja ugljenični materijal razvijene mezoporoznosti čije
se adsorpcione karakteristike mogu poboljšati optimizacijom i kontrolisanjem parametara
dobijanja. U ovom radu je ispitana mogućnost uklanjanja jona teških metala (Cd2+, Ni2+ i
Zn2+) iz vode, korišćenjem karbon kriogela i hemijski modifikovanog karbon kriogela.
Prvi korak u sintezi karbon kriogela je polikondenzacija rezorcinola i formaldehida,
u prisustvu natrijum-karbonata kao katalizatora. Organski kriogel pripremljen je solgel tehnologijom uz naknadno sušenje postupkom zamrzavanja, dok je karbonizacija
organskog kriogela vršena u inertnoj atmosferi argona na temperaturi od 800 o
C [2]. U
cilju poboljšanja adsorpcionih karakteristika karbon kriogela, izvršeno je hemijsko
modifikovanje korišćenjem 5 M HNO3
. Karakterizacija materijala izvršena je merenjem
specifične površine BET metodom, određivanjem tačke nultog naelektrisanja metodom
masene titracije, kao i određivanjem vrsta funkcionalnih grupa prisutnih na površini
materijala, metodom infracrvene spektroskopije sa Furijeovom transformacijom (FTIR).
Ispitan je uticaj pH vrednosti rastvora, početne koncentracije jona metala u rastvoru, kao i
vremena kontakta na adsorpciju teških metala uzorcima karbon kriogela.Primenjenom hemijskom modifikacijom karbon kriogela ne dolazi do bitnijih
promena u specifičnoj površini i poroznosti materijala. S druge strane, ovim postupkom
dolazi do izmene površinske hemije materijala, uvođenjem novih, i povećanjem broja
postojećih kiselih površinskih grupa, što je pokazano FTIR analizom i smanjenjem
vrednosti tačke nultog naelektrisanja sa pHPZC = 9,3 na pHPZC = 3,1. Adsorpcija jona teških
metala na modifikovanom i nemodifikovanom karbon kriogelu vršena je na pH = 6, jer pri
ovoj pH vrednosti materijali pokazuju najveći adsorpcioni kapacitet, a ujedno je izborom
ove pH izbegnuta precipitacija hidroksida metala. Izmene u hemiji površine dovode i do
izmena adsorpcionih karakteristika karbon kriogela. Kako površinske grupe predstavljaju
aktivna mesta za adsorpciju jona teških metala, povećanje količine površinskih grupa kod
modifikovanog karbon kriogela dovodi do višestrukog povećanja adsorpcionog kapaciteta.",
publisher = "Belgrade : Serbian Chemical Society",
journal = "ENVIROCHEM 2018 : 8th Symposium Chemistry and Environmental Protection : program and the book of abstracts",
title = "Karbon kriogel kao adsorbent za uklanjanje Cd(II), Zn(II) i Ni(II) jona iz vode, Carbon cryogel as an adsorbent for removal of Cd(II), Zn(II) and Ni(II) ions from water",
pages = "85-86",
url = "https://hdl.handle.net/21.15107/rcub_vinar_11032"
}

Vukčević, M., Maletić, M., Kalijadis, A., Babić, B., Đurkić, T.,& Laušević, M.. (2018). Karbon kriogel kao adsorbent za uklanjanje Cd(II), Zn(II) i Ni(II) jona iz vode. in ENVIROCHEM 2018 : 8th Symposium Chemistry and Environmental Protection : program and the book of abstracts
Belgrade : Serbian Chemical Society., 85-86.
https://hdl.handle.net/21.15107/rcub_vinar_11032

Vukčević M, Maletić M, Kalijadis A, Babić B, Đurkić T, Laušević M. Karbon kriogel kao adsorbent za uklanjanje Cd(II), Zn(II) i Ni(II) jona iz vode. in ENVIROCHEM 2018 : 8th Symposium Chemistry and Environmental Protection : program and the book of abstracts. 2018;:85-86.
https://hdl.handle.net/21.15107/rcub_vinar_11032 .

Vukčević, Marija, Maletić, Marina, Kalijadis, Ana, Babić, Biljana, Đurkić, Tatjana, Laušević, Mila, "Karbon kriogel kao adsorbent za uklanjanje Cd(II), Zn(II) i Ni(II) jona iz vode" in ENVIROCHEM 2018 : 8th Symposium Chemistry and Environmental Protection : program and the book of abstracts (2018):85-86,
https://hdl.handle.net/21.15107/rcub_vinar_11032 .

TY  - JOUR
AU  - Mijailović, Daniel M.
AU  - Vukčević, Marija M.
AU  - Stević, Zoran M.
AU  - Kalijadis, Ana
AU  - Stojanović, Dušica B.
AU  - Panić, Vladimir V.
AU  - Uskoković, Petar S.
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1583
AB  - Activated carbons with high specific surface area (even above 2000 m(2) g(-1)) and pronounced microporosity are prepared in two-stage process involving conventional carbonization of waste hemp fibers and subsequent activation by potassium hydroxide. Samples with considerably different surface and intrinsic micro-and mesoporous properties are obtained at different carbonization and activation conditions. The improvements of the capacitive properties are found upon increase in carbonization temperature, since it considerably influenced the specific surface area and the content of surface oxygen groups. Cyclic voltammetry experiments reveal the dependence of specific capacitance on the sweep rate due to the characteristic porous structure of the samples. The highest measured value in 1 M H2SO4 solution is 122 F g(-1). The electrochemical impedance data indicates eight-branch transmission line equivalent electric behavior of activated carbons. (C) 2017 The Electrochemical Society. All rights reserved.
T2  - Journal of the Electrochemical Society
T1  - Supercapacitive Performances of Activated Highly Microporous Natural Carbon Macrofibers
VL  - 164
IS  - 6
SP  - A1061
EP  - A1068
DO  - 10.1149/2.0581706jes
ER  - 

@article{
author = "Mijailović, Daniel M. and Vukčević, Marija M. and Stević, Zoran M. and Kalijadis, Ana and Stojanović, Dušica B. and Panić, Vladimir V. and Uskoković, Petar S.",
year = "2017",
abstract = "Activated carbons with high specific surface area (even above 2000 m(2) g(-1)) and pronounced microporosity are prepared in two-stage process involving conventional carbonization of waste hemp fibers and subsequent activation by potassium hydroxide. Samples with considerably different surface and intrinsic micro-and mesoporous properties are obtained at different carbonization and activation conditions. The improvements of the capacitive properties are found upon increase in carbonization temperature, since it considerably influenced the specific surface area and the content of surface oxygen groups. Cyclic voltammetry experiments reveal the dependence of specific capacitance on the sweep rate due to the characteristic porous structure of the samples. The highest measured value in 1 M H2SO4 solution is 122 F g(-1). The electrochemical impedance data indicates eight-branch transmission line equivalent electric behavior of activated carbons. (C) 2017 The Electrochemical Society. All rights reserved.",
journal = "Journal of the Electrochemical Society",
title = "Supercapacitive Performances of Activated Highly Microporous Natural Carbon Macrofibers",
volume = "164",
number = "6",
pages = "A1061-A1068",
doi = "10.1149/2.0581706jes"
}

Mijailović, D. M., Vukčević, M. M., Stević, Z. M., Kalijadis, A., Stojanović, D. B., Panić, V. V.,& Uskoković, P. S.. (2017). Supercapacitive Performances of Activated Highly Microporous Natural Carbon Macrofibers. in Journal of the Electrochemical Society, 164(6), A1061-A1068.
https://doi.org/10.1149/2.0581706jes

Mijailović DM, Vukčević MM, Stević ZM, Kalijadis A, Stojanović DB, Panić VV, Uskoković PS. Supercapacitive Performances of Activated Highly Microporous Natural Carbon Macrofibers. in Journal of the Electrochemical Society. 2017;164(6):A1061-A1068.
doi:10.1149/2.0581706jes .

Mijailović, Daniel M., Vukčević, Marija M., Stević, Zoran M., Kalijadis, Ana, Stojanović, Dušica B., Panić, Vladimir V., Uskoković, Petar S., "Supercapacitive Performances of Activated Highly Microporous Natural Carbon Macrofibers" in Journal of the Electrochemical Society, 164, no. 6 (2017):A1061-A1068,
https://doi.org/10.1149/2.0581706jes . .

TY  - JOUR
AU  - Vukčević, Marija M.
AU  - Pejić, Biljana M.
AU  - Pajić-Lijaković, Ivana
AU  - Kalijadis, Ana
AU  - Kostić, Mirjana M.
AU  - Laušević, Zoran
AU  - Laušević, Mila D.
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1897
AB  - Waste hemp (Cannabis sativa) fibers were used as sustainable and renewable raw materials for production of low-cost biocarbon sorbent for heavy metals removal. Carbon precursors of different chemical composition were obtained by oxidative and alkaline treatments of hemp fibers. Influence of lignocellulosic precursor chemical composition on hemp fibers-based biocarbon (HFB) characteristics was examined by BET surface area measurement, scanning electron microscopy and mass titration. It was found that lignin content and polymorphic transformation of cellulose increase the SBET of microporous HFBs, while hemicelluloses induce more homogeneous distribution of adsorption active sites. Heavy metal ions adsorption onto HFBs is primarily influenced by the amount of surface oxygen groups, while specific surface area plays a secondary role. Equilibrium data obtained for lead ions adsorption were analyzed by different nonlinear adsorption isotherms, and the best fitting model was chosen using standard deviation and Akaike information criterion (AIC(C)). The maximum adsorption capacities of HFBs ranged from 103.1 to 116.3 mg Pb/g. Thermodynamic parameters showed that Pb2+ adsorption onto HFBs is a spontaneous and complex endothermic process, suggesting the coexistence of physisorption and chemisorption mechanisms.
T2  - Journal of the Serbian Chemical Society
T1  - Influence of the precursor chemical composition on heavy metal adsorption properties of hemp (Cannabis Sativa) fibers based biocarbon
VL  - 82
IS  - 12
SP  - 1417
EP  - 1431
DO  - 10.2298/JSC170310080V
ER  - 

@article{
author = "Vukčević, Marija M. and Pejić, Biljana M. and Pajić-Lijaković, Ivana and Kalijadis, Ana and Kostić, Mirjana M. and Laušević, Zoran and Laušević, Mila D.",
year = "2017",
abstract = "Waste hemp (Cannabis sativa) fibers were used as sustainable and renewable raw materials for production of low-cost biocarbon sorbent for heavy metals removal. Carbon precursors of different chemical composition were obtained by oxidative and alkaline treatments of hemp fibers. Influence of lignocellulosic precursor chemical composition on hemp fibers-based biocarbon (HFB) characteristics was examined by BET surface area measurement, scanning electron microscopy and mass titration. It was found that lignin content and polymorphic transformation of cellulose increase the SBET of microporous HFBs, while hemicelluloses induce more homogeneous distribution of adsorption active sites. Heavy metal ions adsorption onto HFBs is primarily influenced by the amount of surface oxygen groups, while specific surface area plays a secondary role. Equilibrium data obtained for lead ions adsorption were analyzed by different nonlinear adsorption isotherms, and the best fitting model was chosen using standard deviation and Akaike information criterion (AIC(C)). The maximum adsorption capacities of HFBs ranged from 103.1 to 116.3 mg Pb/g. Thermodynamic parameters showed that Pb2+ adsorption onto HFBs is a spontaneous and complex endothermic process, suggesting the coexistence of physisorption and chemisorption mechanisms.",
journal = "Journal of the Serbian Chemical Society",
title = "Influence of the precursor chemical composition on heavy metal adsorption properties of hemp (Cannabis Sativa) fibers based biocarbon",
volume = "82",
number = "12",
pages = "1417-1431",
doi = "10.2298/JSC170310080V"
}

Vukčević, M. M., Pejić, B. M., Pajić-Lijaković, I., Kalijadis, A., Kostić, M. M., Laušević, Z.,& Laušević, M. D.. (2017). Influence of the precursor chemical composition on heavy metal adsorption properties of hemp (Cannabis Sativa) fibers based biocarbon. in Journal of the Serbian Chemical Society, 82(12), 1417-1431.
https://doi.org/10.2298/JSC170310080V

Vukčević MM, Pejić BM, Pajić-Lijaković I, Kalijadis A, Kostić MM, Laušević Z, Laušević MD. Influence of the precursor chemical composition on heavy metal adsorption properties of hemp (Cannabis Sativa) fibers based biocarbon. in Journal of the Serbian Chemical Society. 2017;82(12):1417-1431.
doi:10.2298/JSC170310080V .

Vukčević, Marija M., Pejić, Biljana M., Pajić-Lijaković, Ivana, Kalijadis, Ana, Kostić, Mirjana M., Laušević, Zoran, Laušević, Mila D., "Influence of the precursor chemical composition on heavy metal adsorption properties of hemp (Cannabis Sativa) fibers based biocarbon" in Journal of the Serbian Chemical Society, 82, no. 12 (2017):1417-1431,
https://doi.org/10.2298/JSC170310080V . .

TY  - JOUR
AU  - Vukčević, Marija M.
AU  - Kalijadis, Ana
AU  - Vasiljevic, Tatjana M.
AU  - Babić, Biljana M.
AU  - Laušević, Zoran
AU  - Laušević, Mila D.
PY  - 2015
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/621
AB  - The main objective of this work was to find optimal production parameters for the preparation of activated hemp fibers (ACh) with good adsorption properties toward pesticides. In order to examine the role of manufacturing parameters on ACh surface characteristics, activation process of carbonized hemp fibers was investigated by temperature programmed reaction and evolved gaseous products of activation were monitored by mass spectrometry. ACh samples were characterized by BET surface area, scanning electron microscopy and temperature-programmed desorption. KOH activation induces the reduction of oxygen groups existing on the carbonized hemp fiber surface and the formation of the more stable, predominantly anhydride groups, while porosity development correlates with both H-2 and CO, evolved during the activation, and increases with carbonization and activation temperature. Finally, the highest efficiency in pesticides removal was achieved by carbonization of waste hemp fibers and activation at 900 degrees C with KOH/carbonized material ratio of 2/1. High efficiency in pesticides removal indicates that activated hemp fibers could be successfully used as a sorbent in water purification. (C) 2015 Elsevier Inc. All rights reserved.
T2  - Microporous and Mesoporous Materials
T1  - Production of activated carbon derived from waste hemp (Cannabis sativa) fibers and its performance in pesticide adsorption
VL  - 214
SP  - 156
EP  - 165
DO  - 10.1016/j.micromeso.2015.05.012
ER  - 

@article{
author = "Vukčević, Marija M. and Kalijadis, Ana and Vasiljevic, Tatjana M. and Babić, Biljana M. and Laušević, Zoran and Laušević, Mila D.",
year = "2015",
abstract = "The main objective of this work was to find optimal production parameters for the preparation of activated hemp fibers (ACh) with good adsorption properties toward pesticides. In order to examine the role of manufacturing parameters on ACh surface characteristics, activation process of carbonized hemp fibers was investigated by temperature programmed reaction and evolved gaseous products of activation were monitored by mass spectrometry. ACh samples were characterized by BET surface area, scanning electron microscopy and temperature-programmed desorption. KOH activation induces the reduction of oxygen groups existing on the carbonized hemp fiber surface and the formation of the more stable, predominantly anhydride groups, while porosity development correlates with both H-2 and CO, evolved during the activation, and increases with carbonization and activation temperature. Finally, the highest efficiency in pesticides removal was achieved by carbonization of waste hemp fibers and activation at 900 degrees C with KOH/carbonized material ratio of 2/1. High efficiency in pesticides removal indicates that activated hemp fibers could be successfully used as a sorbent in water purification. (C) 2015 Elsevier Inc. All rights reserved.",
journal = "Microporous and Mesoporous Materials",
title = "Production of activated carbon derived from waste hemp (Cannabis sativa) fibers and its performance in pesticide adsorption",
volume = "214",
pages = "156-165",
doi = "10.1016/j.micromeso.2015.05.012"
}

Vukčević, M. M., Kalijadis, A., Vasiljevic, T. M., Babić, B. M., Laušević, Z.,& Laušević, M. D.. (2015). Production of activated carbon derived from waste hemp (Cannabis sativa) fibers and its performance in pesticide adsorption. in Microporous and Mesoporous Materials, 214, 156-165.
https://doi.org/10.1016/j.micromeso.2015.05.012

Vukčević MM, Kalijadis A, Vasiljevic TM, Babić BM, Laušević Z, Laušević MD. Production of activated carbon derived from waste hemp (Cannabis sativa) fibers and its performance in pesticide adsorption. in Microporous and Mesoporous Materials. 2015;214:156-165.
doi:10.1016/j.micromeso.2015.05.012 .

Vukčević, Marija M., Kalijadis, Ana, Vasiljevic, Tatjana M., Babić, Biljana M., Laušević, Zoran, Laušević, Mila D., "Production of activated carbon derived from waste hemp (Cannabis sativa) fibers and its performance in pesticide adsorption" in Microporous and Mesoporous Materials, 214 (2015):156-165,
https://doi.org/10.1016/j.micromeso.2015.05.012 . .

TY  - JOUR
AU  - Kalijadis, Ana
AU  - Vukčević, Marija M.
AU  - Jovanović, Zoran M.
AU  - Laušević, Zoran
AU  - Laušević, Mila D.
PY  - 2011
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/4342
AB  - The surface characteristics of different carbon materials: activated carbon, carbon felt, glassy carbon and a porous carbon monolith were investigated. The specific surface area was examined by the BET method with N(2) adsorption, the amount and the type of surface oxygen groups by Boehm titration as well as by temperature-programmed desorption (TPD). By comparing the results obtained using BET analysis with those of TPD and the Boehm method, it was found that the number of surface groups was not proportional to the specific surface area. The total amount of oxygen groups, obtained by TPD, is higher than the amount obtained by Boehms method for porous samples. The inconsistencies between these results originate from the fact that the Boehm method is limited to the determination of acidic and basic groups, whereas TPD provides information on the total number of all surface oxygen groups. In addition, the presence of porosity could reduce the solvent-accessible surface in the Boehm method. The TPD profiles of CO evolution showed the presence of a low temperature maximum, below 650 K, which originates from CO(2) reduction on the carbon material surface.
T2  - Journal of the Serbian Chemical Society
T1  - Characterisation of surface oxygen groups on different carbon materials by the Boehm method and temperature-programmed desorption
VL  - 76
IS  - 5
SP  - 757
EP  - 768
DO  - 10.2298/JSC091224056K
ER  - 

@article{
author = "Kalijadis, Ana and Vukčević, Marija M. and Jovanović, Zoran M. and Laušević, Zoran and Laušević, Mila D.",
year = "2011",
abstract = "The surface characteristics of different carbon materials: activated carbon, carbon felt, glassy carbon and a porous carbon monolith were investigated. The specific surface area was examined by the BET method with N(2) adsorption, the amount and the type of surface oxygen groups by Boehm titration as well as by temperature-programmed desorption (TPD). By comparing the results obtained using BET analysis with those of TPD and the Boehm method, it was found that the number of surface groups was not proportional to the specific surface area. The total amount of oxygen groups, obtained by TPD, is higher than the amount obtained by Boehms method for porous samples. The inconsistencies between these results originate from the fact that the Boehm method is limited to the determination of acidic and basic groups, whereas TPD provides information on the total number of all surface oxygen groups. In addition, the presence of porosity could reduce the solvent-accessible surface in the Boehm method. The TPD profiles of CO evolution showed the presence of a low temperature maximum, below 650 K, which originates from CO(2) reduction on the carbon material surface.",
journal = "Journal of the Serbian Chemical Society",
title = "Characterisation of surface oxygen groups on different carbon materials by the Boehm method and temperature-programmed desorption",
volume = "76",
number = "5",
pages = "757-768",
doi = "10.2298/JSC091224056K"
}

Kalijadis, A., Vukčević, M. M., Jovanović, Z. M., Laušević, Z.,& Laušević, M. D.. (2011). Characterisation of surface oxygen groups on different carbon materials by the Boehm method and temperature-programmed desorption. in Journal of the Serbian Chemical Society, 76(5), 757-768.
https://doi.org/10.2298/JSC091224056K

Kalijadis A, Vukčević MM, Jovanović ZM, Laušević Z, Laušević MD. Characterisation of surface oxygen groups on different carbon materials by the Boehm method and temperature-programmed desorption. in Journal of the Serbian Chemical Society. 2011;76(5):757-768.
doi:10.2298/JSC091224056K .

Kalijadis, Ana, Vukčević, Marija M., Jovanović, Zoran M., Laušević, Zoran, Laušević, Mila D., "Characterisation of surface oxygen groups on different carbon materials by the Boehm method and temperature-programmed desorption" in Journal of the Serbian Chemical Society, 76, no. 5 (2011):757-768,
https://doi.org/10.2298/JSC091224056K . .

TY  - JOUR
AU  - Jovanović, Zoran M.
AU  - Kalijadis, Ana
AU  - Vukčević, Marija M.
AU  - Laušević, Zoran
AU  - Laušević, Mila D.
PY  - 2009
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/6854
AB  - Carbon monolith was treated with HNO(3), KOH and H(2)O(2). Effects of these treatments on the surface functional groups and on the amount of silver deposited on the CM surface were studied by temperature programmed desorption (TPD) and atomic absorption spectrometry (AAS). As a result of chemical treatment there was an increase in the amount of surface oxygen complexes. The increase in the amount of silver deposit is proportional to the amount of surface groups that produce CO under decomposition. However, the high amount of CO groups, decomposing above 600 degrees C, induces the smaller Ag crystallite size. Therefore, the high temperature CO evolving oxides are, most likely, the initial centers for Ag deposition.
T2  - Hemijska industrija
T1  - Silver Deposition on Chemically Treated Carbon Monolith
VL  - 63
IS  - 3
SP  - 195
EP  - 200
DO  - 10.2298/HEMIND0903195J
ER  - 

@article{
author = "Jovanović, Zoran M. and Kalijadis, Ana and Vukčević, Marija M. and Laušević, Zoran and Laušević, Mila D.",
year = "2009",
abstract = "Carbon monolith was treated with HNO(3), KOH and H(2)O(2). Effects of these treatments on the surface functional groups and on the amount of silver deposited on the CM surface were studied by temperature programmed desorption (TPD) and atomic absorption spectrometry (AAS). As a result of chemical treatment there was an increase in the amount of surface oxygen complexes. The increase in the amount of silver deposit is proportional to the amount of surface groups that produce CO under decomposition. However, the high amount of CO groups, decomposing above 600 degrees C, induces the smaller Ag crystallite size. Therefore, the high temperature CO evolving oxides are, most likely, the initial centers for Ag deposition.",
journal = "Hemijska industrija",
title = "Silver Deposition on Chemically Treated Carbon Monolith",
volume = "63",
number = "3",
pages = "195-200",
doi = "10.2298/HEMIND0903195J"
}

Jovanović, Z. M., Kalijadis, A., Vukčević, M. M., Laušević, Z.,& Laušević, M. D.. (2009). Silver Deposition on Chemically Treated Carbon Monolith. in Hemijska industrija, 63(3), 195-200.
https://doi.org/10.2298/HEMIND0903195J

Jovanović ZM, Kalijadis A, Vukčević MM, Laušević Z, Laušević MD. Silver Deposition on Chemically Treated Carbon Monolith. in Hemijska industrija. 2009;63(3):195-200.
doi:10.2298/HEMIND0903195J .

Jovanović, Zoran M., Kalijadis, Ana, Vukčević, Marija M., Laušević, Zoran, Laušević, Mila D., "Silver Deposition on Chemically Treated Carbon Monolith" in Hemijska industrija, 63, no. 3 (2009):195-200,
https://doi.org/10.2298/HEMIND0903195J . .