TY  - JOUR
AU  - Stamenković, Tijana
AU  - Radmilović, Nadežda
AU  - Prekajski-Đorđević, Marija D.
AU  - Rabasović, Mihailo
AU  - Dinić, Ivana
AU  - Tomić, Miloš
AU  - Lojpur, Vesna
AU  - Mančić, Lidija
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10499
AB  - Nanopowders of up-conversion SrGd2O4 orthorhombic (Pnma) phase co-doped with different Yb3+ (1, 2.5 and 5 at%) and constant Er3+ (0.5 at%) ions were successfully prepared via sol-gel assisted combustion. Rietveld refinement indicated unit cell lattice parameters increase with Yb3+ and Er3+ ions doping. Scanning transmission electron microscopy with corresponding energy-dispersive X-ray spectroscopy revealed that obtained powders are composed of agglomerated nanoparticles that have a uniform distribution of all constituting elements. Photoluminescence measurements implied intensification of the up-conversion (UC) emission in the visible part of spectrum with the increase of Yb3+ content, which is followed by a significant change in the green to red ratio. Two-photon UC processes are established as a result of Er3+ f-f electronic transitions: green emission at 523 and 551 nm (2H11/2, 4S3/2 → 4I15/2) as well as a red emission at 661 nm (4F9/2 → 4I15/2). The highest value of absolute quantum yield of 0.055% is determined for SrGd2O4 nanoparticles doped with 0.5 at% of Er3+ and co-doped with 5 at% of Yb3+ (λexc = 976 nm, power density 200 W/cm2).
T2  - Journal of Luminescence
T1  - Quantum yield and energy transfer in up-conversion SrGd2O4:Yb, Er nanoparticles obtained via sol-gel assisted combustion
VL  - 253
SP  - 119491
DO  - 10.1016/j.jlumin.2022.119491
ER  - 

@article{
author = "Stamenković, Tijana and Radmilović, Nadežda and Prekajski-Đorđević, Marija D. and Rabasović, Mihailo and Dinić, Ivana and Tomić, Miloš and Lojpur, Vesna and Mančić, Lidija",
year = "2023",
abstract = "Nanopowders of up-conversion SrGd2O4 orthorhombic (Pnma) phase co-doped with different Yb3+ (1, 2.5 and 5 at%) and constant Er3+ (0.5 at%) ions were successfully prepared via sol-gel assisted combustion. Rietveld refinement indicated unit cell lattice parameters increase with Yb3+ and Er3+ ions doping. Scanning transmission electron microscopy with corresponding energy-dispersive X-ray spectroscopy revealed that obtained powders are composed of agglomerated nanoparticles that have a uniform distribution of all constituting elements. Photoluminescence measurements implied intensification of the up-conversion (UC) emission in the visible part of spectrum with the increase of Yb3+ content, which is followed by a significant change in the green to red ratio. Two-photon UC processes are established as a result of Er3+ f-f electronic transitions: green emission at 523 and 551 nm (2H11/2, 4S3/2 → 4I15/2) as well as a red emission at 661 nm (4F9/2 → 4I15/2). The highest value of absolute quantum yield of 0.055% is determined for SrGd2O4 nanoparticles doped with 0.5 at% of Er3+ and co-doped with 5 at% of Yb3+ (λexc = 976 nm, power density 200 W/cm2).",
journal = "Journal of Luminescence",
title = "Quantum yield and energy transfer in up-conversion SrGd2O4:Yb, Er nanoparticles obtained via sol-gel assisted combustion",
volume = "253",
pages = "119491",
doi = "10.1016/j.jlumin.2022.119491"
}

Stamenković, T., Radmilović, N., Prekajski-Đorđević, M. D., Rabasović, M., Dinić, I., Tomić, M., Lojpur, V.,& Mančić, L.. (2023). Quantum yield and energy transfer in up-conversion SrGd2O4:Yb, Er nanoparticles obtained via sol-gel assisted combustion. in Journal of Luminescence, 253, 119491.
https://doi.org/10.1016/j.jlumin.2022.119491

Stamenković T, Radmilović N, Prekajski-Đorđević MD, Rabasović M, Dinić I, Tomić M, Lojpur V, Mančić L. Quantum yield and energy transfer in up-conversion SrGd2O4:Yb, Er nanoparticles obtained via sol-gel assisted combustion. in Journal of Luminescence. 2023;253:119491.
doi:10.1016/j.jlumin.2022.119491 .

Stamenković, Tijana, Radmilović, Nadežda, Prekajski-Đorđević, Marija D., Rabasović, Mihailo, Dinić, Ivana, Tomić, Miloš, Lojpur, Vesna, Mančić, Lidija, "Quantum yield and energy transfer in up-conversion SrGd2O4:Yb, Er nanoparticles obtained via sol-gel assisted combustion" in Journal of Luminescence, 253 (2023):119491,
https://doi.org/10.1016/j.jlumin.2022.119491 . .

TY  - JOUR
AU  - Tomić, Miloš
AU  - Dunjić, Branko
AU  - Nikolić, Marija S.
AU  - Trifković, Kata
AU  - Stanković, Nadežda
AU  - Pavlović, Vladimir B.
AU  - Bajat, Jelena B.
AU  - Đonlagić, Jasna A.
PY  - 2019
UR  - https://linkinghub.elsevier.com/retrieve/pii/S0300944018312487
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8076
AB  - In the present study the commercial multifunctional fatty acid polyamidoamine (PAA) was for the first time simultaneously applied as a curing agent and clay modifier for epoxy/clay nanocomposites (NC) based on diglycidyl ether of bisphenol A. The montmorillonite (Cloisite®Na + ) was modified with different quantities of partially and fully protonated polyamidoamine. The NCs with 0.5 wt% novel organoclay were prepared by solution intercalation method. The major aims of this paper are investigations of the effects of the composition of PAA modified clays on structure, mechanical, barrier properties and corrosion stability on steel substrates of NCs were studied. The thermogravimetric, flame photometry and X-ray diffraction analyses confirmed the efficient modification of clay surface with polyamidoamine, predominantly located within layers. The NCs exhibited an intercalated/exfoliated morphology and the presence of free amino groups and increased content of modifier facilitated dispersion of clay particles within the polymer matrix, as shown by electron microscopy techniques (SEM, TEM). Under an optimized loading of PAA (molar quantity of total amino groups per clay cation exchange capacity of 1.75), the layers in stacks were separated by 5.0 nm and high number of individual layers was present in NC. Clay modified by PAA with free amino groups showed increased storage modulus in the rubbery state, glass transition temperature of NCs, while dumping factor was decreased. The tensile test confirmed that introduction of flexible modifier on the epoxy/clay interface lead to increase in the ultimate tensile strenght and elongation at break by 31% and toughness up to 83%. The electrochemical impedance spectroscopy and permeability tests proved the pronounced barrier effect of clay particles against corrosive species and water vapor when high dispersion degree of clay in NC was achieved. © 2019 Elsevier B.V.
T2  - Progress in Organic Coatings
T1  - Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites
VL  - 131
SP  - 311
EP  - 321
DO  - 10.1016/j.porgcoat.2019.02.037
ER  - 

@article{
author = "Tomić, Miloš and Dunjić, Branko and Nikolić, Marija S. and Trifković, Kata and Stanković, Nadežda and Pavlović, Vladimir B. and Bajat, Jelena B. and Đonlagić, Jasna A.",
year = "2019",
abstract = "In the present study the commercial multifunctional fatty acid polyamidoamine (PAA) was for the first time simultaneously applied as a curing agent and clay modifier for epoxy/clay nanocomposites (NC) based on diglycidyl ether of bisphenol A. The montmorillonite (Cloisite®Na + ) was modified with different quantities of partially and fully protonated polyamidoamine. The NCs with 0.5 wt% novel organoclay were prepared by solution intercalation method. The major aims of this paper are investigations of the effects of the composition of PAA modified clays on structure, mechanical, barrier properties and corrosion stability on steel substrates of NCs were studied. The thermogravimetric, flame photometry and X-ray diffraction analyses confirmed the efficient modification of clay surface with polyamidoamine, predominantly located within layers. The NCs exhibited an intercalated/exfoliated morphology and the presence of free amino groups and increased content of modifier facilitated dispersion of clay particles within the polymer matrix, as shown by electron microscopy techniques (SEM, TEM). Under an optimized loading of PAA (molar quantity of total amino groups per clay cation exchange capacity of 1.75), the layers in stacks were separated by 5.0 nm and high number of individual layers was present in NC. Clay modified by PAA with free amino groups showed increased storage modulus in the rubbery state, glass transition temperature of NCs, while dumping factor was decreased. The tensile test confirmed that introduction of flexible modifier on the epoxy/clay interface lead to increase in the ultimate tensile strenght and elongation at break by 31% and toughness up to 83%. The electrochemical impedance spectroscopy and permeability tests proved the pronounced barrier effect of clay particles against corrosive species and water vapor when high dispersion degree of clay in NC was achieved. © 2019 Elsevier B.V.",
journal = "Progress in Organic Coatings",
title = "Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites",
volume = "131",
pages = "311-321",
doi = "10.1016/j.porgcoat.2019.02.037"
}

Tomić, M., Dunjić, B., Nikolić, M. S., Trifković, K., Stanković, N., Pavlović, V. B., Bajat, J. B.,& Đonlagić, J. A.. (2019). Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites. in Progress in Organic Coatings, 131, 311-321.
https://doi.org/10.1016/j.porgcoat.2019.02.037

Tomić M, Dunjić B, Nikolić MS, Trifković K, Stanković N, Pavlović VB, Bajat JB, Đonlagić JA. Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites. in Progress in Organic Coatings. 2019;131:311-321.
doi:10.1016/j.porgcoat.2019.02.037 .

Tomić, Miloš, Dunjić, Branko, Nikolić, Marija S., Trifković, Kata, Stanković, Nadežda, Pavlović, Vladimir B., Bajat, Jelena B., Đonlagić, Jasna A., "Polyamidoamine as a clay modifier and curing agent in preparation of epoxy nanocomposites" in Progress in Organic Coatings, 131 (2019):311-321,
https://doi.org/10.1016/j.porgcoat.2019.02.037 . .

TY  - JOUR
AU  - Tomić, Miloš
AU  - Dunjić, Branko
AU  - Nikolić, Marija S.
AU  - Maletaškić, Jelena
AU  - Pavlović, Vladimir B.
AU  - Bajat, Jelena B.
AU  - Đonlagić, Jasna A.
PY  - 2018
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1951
AB  - The major aims of this paper are the investigation of the effects of the mixing procedure and the montmorillonite (Mt) surface modification on the structure (optical microscopy, XRD, TEM, SEM), rheological, mechanical properties (DMA, tensile test) and corrosion stability (electrochemical impedance spectroscopy) of clay mineral/epoxy nanocomposite (CPN). Two series of CPN samples were prepared based on diglycidyl ether of bisphenol A (DGEBA) and polyamidoamine curing agent with three organophilic Mt and sodium-montmorillonite (1 wt%). Mt were mixed with DGEBA solution in the powder (direct mixing) and in the form of dispersions, preswollen in a commercial coating thinner (solution intercalation). The commercial Mt (Cloisite 30B) modified by quaternary alkylammonium ions bearing hydroxyl groups and especially Mt functionalized by primary (HDA(+)-Mt) alkylammonium ions, at loadings close to cation exchange capacity (CRC), were significantly swollen by thinner and further uniformly dispersed into CPN. Meanwhile, low gel volumes in thinner were found for more hydrophobic Mt (Cloisite 15A). The compatibility of Mt with solvents was well described by solubility and Flory-Huggins interaction parameters. In contrast to the direct incorporation of Mt powders in CPN, swelling enhanced intercalation of epoxy matrix into Mt, and for HDA(+)-Mt based CPN interlayer spacing reached 4.4 nm. The usage of HDA(+)-Mt organoclay and solution intercalation procedure provided the highest enhancement in rheological parameters (G, G, of Mt/epoxy dispersions and glassy storage modulus, Youngs modulus and barrier properties of cured CPN.
T2  - Applied Clay Science
T1  - Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods
VL  - 154
SP  - 52
EP  - 63
DO  - 10.1016/j.clay.2017.12.047
ER  - 

@article{
author = "Tomić, Miloš and Dunjić, Branko and Nikolić, Marija S. and Maletaškić, Jelena and Pavlović, Vladimir B. and Bajat, Jelena B. and Đonlagić, Jasna A.",
year = "2018",
abstract = "The major aims of this paper are the investigation of the effects of the mixing procedure and the montmorillonite (Mt) surface modification on the structure (optical microscopy, XRD, TEM, SEM), rheological, mechanical properties (DMA, tensile test) and corrosion stability (electrochemical impedance spectroscopy) of clay mineral/epoxy nanocomposite (CPN). Two series of CPN samples were prepared based on diglycidyl ether of bisphenol A (DGEBA) and polyamidoamine curing agent with three organophilic Mt and sodium-montmorillonite (1 wt%). Mt were mixed with DGEBA solution in the powder (direct mixing) and in the form of dispersions, preswollen in a commercial coating thinner (solution intercalation). The commercial Mt (Cloisite 30B) modified by quaternary alkylammonium ions bearing hydroxyl groups and especially Mt functionalized by primary (HDA(+)-Mt) alkylammonium ions, at loadings close to cation exchange capacity (CRC), were significantly swollen by thinner and further uniformly dispersed into CPN. Meanwhile, low gel volumes in thinner were found for more hydrophobic Mt (Cloisite 15A). The compatibility of Mt with solvents was well described by solubility and Flory-Huggins interaction parameters. In contrast to the direct incorporation of Mt powders in CPN, swelling enhanced intercalation of epoxy matrix into Mt, and for HDA(+)-Mt based CPN interlayer spacing reached 4.4 nm. The usage of HDA(+)-Mt organoclay and solution intercalation procedure provided the highest enhancement in rheological parameters (G, G, of Mt/epoxy dispersions and glassy storage modulus, Youngs modulus and barrier properties of cured CPN.",
journal = "Applied Clay Science",
title = "Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods",
volume = "154",
pages = "52-63",
doi = "10.1016/j.clay.2017.12.047"
}

Tomić, M., Dunjić, B., Nikolić, M. S., Maletaškić, J., Pavlović, V. B., Bajat, J. B.,& Đonlagić, J. A.. (2018). Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods. in Applied Clay Science, 154, 52-63.
https://doi.org/10.1016/j.clay.2017.12.047

Tomić M, Dunjić B, Nikolić MS, Maletaškić J, Pavlović VB, Bajat JB, Đonlagić JA. Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods. in Applied Clay Science. 2018;154:52-63.
doi:10.1016/j.clay.2017.12.047 .

Tomić, Miloš, Dunjić, Branko, Nikolić, Marija S., Maletaškić, Jelena, Pavlović, Vladimir B., Bajat, Jelena B., Đonlagić, Jasna A., "Dispersion efficiency of montmorillonites in epoxy nanocomposites using solution intercalation and direct mixing methods" in Applied Clay Science, 154 (2018):52-63,
https://doi.org/10.1016/j.clay.2017.12.047 . .

TY  - JOUR
AU  - Davidović, Slađana Z.
AU  - Miljković, Miona G.
AU  - Tomić, Miloš
AU  - Gordić, Milan V.
AU  - Nešić, Aleksandra
AU  - Dimitrijević, Suzana I.
PY  - 2018
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1932
AB  - The aim of this study was to develop dextran-based edible films plasticized by sorbitol. In order to optimise the film-forming formulation, response surface methodology was used. The influence of dextran and sorbitol concentration on the mechanical and water vapour barrier properties of obtained films was investigated. The results showed that both parameters exhibited significant effect on the water vapour permeability of a film. Both dextran and sorbitol concentration had significant influence on tensile strength and elongation at break, whereas only sorbitol concentration had significant effect on Youngs modulus. After optimisation by desirability approach, it was found that a film made of 3.40 wt% of dextran and 20.43 wt% of sorbitol showed the lowest water vapour permeability and the highest tensile strength and elasticity.
T2  - Carbohydrate Polymers
T1  - Response surface methodology for optimisation of edible coatings based on dextran from Leuconostoc mesenteroides T3
VL  - 184
SP  - 207
EP  - 213
DO  - 10.1016/j.carbpol.2017.12.061
ER  - 

@article{
author = "Davidović, Slađana Z. and Miljković, Miona G. and Tomić, Miloš and Gordić, Milan V. and Nešić, Aleksandra and Dimitrijević, Suzana I.",
year = "2018",
abstract = "The aim of this study was to develop dextran-based edible films plasticized by sorbitol. In order to optimise the film-forming formulation, response surface methodology was used. The influence of dextran and sorbitol concentration on the mechanical and water vapour barrier properties of obtained films was investigated. The results showed that both parameters exhibited significant effect on the water vapour permeability of a film. Both dextran and sorbitol concentration had significant influence on tensile strength and elongation at break, whereas only sorbitol concentration had significant effect on Youngs modulus. After optimisation by desirability approach, it was found that a film made of 3.40 wt% of dextran and 20.43 wt% of sorbitol showed the lowest water vapour permeability and the highest tensile strength and elasticity.",
journal = "Carbohydrate Polymers",
title = "Response surface methodology for optimisation of edible coatings based on dextran from Leuconostoc mesenteroides T3",
volume = "184",
pages = "207-213",
doi = "10.1016/j.carbpol.2017.12.061"
}

Davidović, S. Z., Miljković, M. G., Tomić, M., Gordić, M. V., Nešić, A.,& Dimitrijević, S. I.. (2018). Response surface methodology for optimisation of edible coatings based on dextran from Leuconostoc mesenteroides T3. in Carbohydrate Polymers, 184, 207-213.
https://doi.org/10.1016/j.carbpol.2017.12.061

Davidović SZ, Miljković MG, Tomić M, Gordić MV, Nešić A, Dimitrijević SI. Response surface methodology for optimisation of edible coatings based on dextran from Leuconostoc mesenteroides T3. in Carbohydrate Polymers. 2018;184:207-213.
doi:10.1016/j.carbpol.2017.12.061 .

Davidović, Slađana Z., Miljković, Miona G., Tomić, Miloš, Gordić, Milan V., Nešić, Aleksandra, Dimitrijević, Suzana I., "Response surface methodology for optimisation of edible coatings based on dextran from Leuconostoc mesenteroides T3" in Carbohydrate Polymers, 184 (2018):207-213,
https://doi.org/10.1016/j.carbpol.2017.12.061 . .

TY  - JOUR
AU  - Kovačević, Tihomir
AU  - Rusmirović, Jelena D.
AU  - Tomić, Nataša
AU  - Marinović-Cincović, Milena
AU  - Kamberović, Željko
AU  - Tomić, Miloš
AU  - Marinković, Aleksandar D.
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1708
AB  - Influence of the addition of three different non-metallic fractions (NMF), obtained by processing of printed circuit boards (PCBs), on the mechanical and thermal properties of unsaturated polyester resin (UPR) based composites were studied in this paper. UPR, based on products of PET depolymerization, and NMF were characterized using FTIR, NMR, optical microscopy and SEM/EDS analysis. Cross-linking density (v), storage modulus (G), damping factor (tan delta) and glass transition temperature (T-g) of the composites were determined from the DMA testing. Tensile (sigma(t)) and flexural (sigma(f)) strength, and micro Vickers hardness indicated good composite performance under static load. Thermal and flame resistant properties were analyzed by TGA/DTG and UL-94 flammability test whereby V-2 category of appropriate composite was achieved. Composites with satisfactory mechanical and thermal properties reflected synergetic effect of constituents obtained from waste materials. (C) 2017 Elsevier Ltd. All rights reserved.
T2  - Composites: Part B: Engineering
T1  - New composites based on waste PET and non-metallic fraction from waste printed circuit boards: Mechanical and thermal properties
VL  - 127
SP  - 1
EP  - 14
DO  - 10.1016/j.compositesb.2017.06.020
ER  - 

@article{
author = "Kovačević, Tihomir and Rusmirović, Jelena D. and Tomić, Nataša and Marinović-Cincović, Milena and Kamberović, Željko and Tomić, Miloš and Marinković, Aleksandar D.",
year = "2017",
abstract = "Influence of the addition of three different non-metallic fractions (NMF), obtained by processing of printed circuit boards (PCBs), on the mechanical and thermal properties of unsaturated polyester resin (UPR) based composites were studied in this paper. UPR, based on products of PET depolymerization, and NMF were characterized using FTIR, NMR, optical microscopy and SEM/EDS analysis. Cross-linking density (v), storage modulus (G), damping factor (tan delta) and glass transition temperature (T-g) of the composites were determined from the DMA testing. Tensile (sigma(t)) and flexural (sigma(f)) strength, and micro Vickers hardness indicated good composite performance under static load. Thermal and flame resistant properties were analyzed by TGA/DTG and UL-94 flammability test whereby V-2 category of appropriate composite was achieved. Composites with satisfactory mechanical and thermal properties reflected synergetic effect of constituents obtained from waste materials. (C) 2017 Elsevier Ltd. All rights reserved.",
journal = "Composites: Part B: Engineering",
title = "New composites based on waste PET and non-metallic fraction from waste printed circuit boards: Mechanical and thermal properties",
volume = "127",
pages = "1-14",
doi = "10.1016/j.compositesb.2017.06.020"
}

Kovačević, T., Rusmirović, J. D., Tomić, N., Marinović-Cincović, M., Kamberović, Ž., Tomić, M.,& Marinković, A. D.. (2017). New composites based on waste PET and non-metallic fraction from waste printed circuit boards: Mechanical and thermal properties. in Composites: Part B: Engineering, 127, 1-14.
https://doi.org/10.1016/j.compositesb.2017.06.020

Kovačević T, Rusmirović JD, Tomić N, Marinović-Cincović M, Kamberović Ž, Tomić M, Marinković AD. New composites based on waste PET and non-metallic fraction from waste printed circuit boards: Mechanical and thermal properties. in Composites: Part B: Engineering. 2017;127:1-14.
doi:10.1016/j.compositesb.2017.06.020 .

Kovačević, Tihomir, Rusmirović, Jelena D., Tomić, Nataša, Marinović-Cincović, Milena, Kamberović, Željko, Tomić, Miloš, Marinković, Aleksandar D., "New composites based on waste PET and non-metallic fraction from waste printed circuit boards: Mechanical and thermal properties" in Composites: Part B: Engineering, 127 (2017):1-14,
https://doi.org/10.1016/j.compositesb.2017.06.020 . .