TY  - JOUR
AU  - Jelić, Aleksandra
AU  - Marinković, Aleksandar D.
AU  - Sekulić, Milica
AU  - Dikić, Stefan
AU  - Ugrinović, Vukašin
AU  - Pavlović, Vladimir B.
AU  - Putić, Slaviša
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9562
AB  - In this study, halloysite nanotubes (HNT) were modified by: 3-glycidyloxypropyltrimethoxysilane (GLYMO), 3-aminopropyltrimethoxysilane (APTES), and 2,2-Bis[4-(glycidyloxy) phenyl] propane (DGEBA), and incorporated in the epoxy resin matrix to enhance its mechanical properties. The HNT/epoxy nanocomposite materials were prepared by mixing different ratios of untreated/treated HNT with neat epoxy resin. Characterization of untreated/treated HNT was performed by Fourier-transformation infrared (FTIR) spectroscopy, and X-ray diffraction (XRD). The quantity of grafted molecules and thermal stability of newly synthesized materials were determined by thermogravimetric (TG) and derivative thermogravimetric (DTG) analysis. Tensile properties of newly synthesized materials were compared, and scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis of the fracture surfaces were performed. Incorporation of APTES modified HNT (HNTAPT) and two-step modification APTES followed by DGEBA (HNTAPTDG) has increased the tensile strength of the nanocomposite materials up to 72% and 61%, and strain at break up to 1082% and 1216%, respectively, compared to neat epoxy. It was concluded that the modification of HNT contributed to the enhancement of the dispersion and the cross-linking in the epoxy resin matrix. © 2021 Society of Plastics Engineers
T2  - Polymer Composites
T1  - Design of halloysite modification for improvement of mechanical properties of the epoxy based nanocomposites
VL  - 42
IS  - 5
SP  - 2180
EP  - 2192
DO  - 10.1002/pc.25967
ER  - 

@article{
author = "Jelić, Aleksandra and Marinković, Aleksandar D. and Sekulić, Milica and Dikić, Stefan and Ugrinović, Vukašin and Pavlović, Vladimir B. and Putić, Slaviša",
year = "2021",
abstract = "In this study, halloysite nanotubes (HNT) were modified by: 3-glycidyloxypropyltrimethoxysilane (GLYMO), 3-aminopropyltrimethoxysilane (APTES), and 2,2-Bis[4-(glycidyloxy) phenyl] propane (DGEBA), and incorporated in the epoxy resin matrix to enhance its mechanical properties. The HNT/epoxy nanocomposite materials were prepared by mixing different ratios of untreated/treated HNT with neat epoxy resin. Characterization of untreated/treated HNT was performed by Fourier-transformation infrared (FTIR) spectroscopy, and X-ray diffraction (XRD). The quantity of grafted molecules and thermal stability of newly synthesized materials were determined by thermogravimetric (TG) and derivative thermogravimetric (DTG) analysis. Tensile properties of newly synthesized materials were compared, and scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis of the fracture surfaces were performed. Incorporation of APTES modified HNT (HNTAPT) and two-step modification APTES followed by DGEBA (HNTAPTDG) has increased the tensile strength of the nanocomposite materials up to 72% and 61%, and strain at break up to 1082% and 1216%, respectively, compared to neat epoxy. It was concluded that the modification of HNT contributed to the enhancement of the dispersion and the cross-linking in the epoxy resin matrix. © 2021 Society of Plastics Engineers",
journal = "Polymer Composites",
title = "Design of halloysite modification for improvement of mechanical properties of the epoxy based nanocomposites",
volume = "42",
number = "5",
pages = "2180-2192",
doi = "10.1002/pc.25967"
}

Jelić, A., Marinković, A. D., Sekulić, M., Dikić, S., Ugrinović, V., Pavlović, V. B.,& Putić, S.. (2021). Design of halloysite modification for improvement of mechanical properties of the epoxy based nanocomposites. in Polymer Composites, 42(5), 2180-2192.
https://doi.org/10.1002/pc.25967

Jelić A, Marinković AD, Sekulić M, Dikić S, Ugrinović V, Pavlović VB, Putić S. Design of halloysite modification for improvement of mechanical properties of the epoxy based nanocomposites. in Polymer Composites. 2021;42(5):2180-2192.
doi:10.1002/pc.25967 .

Jelić, Aleksandra, Marinković, Aleksandar D., Sekulić, Milica, Dikić, Stefan, Ugrinović, Vukašin, Pavlović, Vladimir B., Putić, Slaviša, "Design of halloysite modification for improvement of mechanical properties of the epoxy based nanocomposites" in Polymer Composites, 42, no. 5 (2021):2180-2192,
https://doi.org/10.1002/pc.25967 . .

TY  - CHAP
AU  - Jelić, Aleksandra
AU  - Božić, Aleksandra
AU  - Stamenović, Marina
AU  - Sekulić, Milica
AU  - Porobić, Slavica
AU  - Dikić, Stefan
AU  - Putić, Slaviša
AU  - Mitrović, Nenad
AU  - Mladenović, Goran
AU  - Mitrović, Aleksandra
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9636
AB  - Halloysite nanotubes (HNTs), naturally occurring as aluminosilicate nanoclay mineral, have recently emerged as a possible nanomaterial for countless applications due to their specific chemical structure, tubular shape, high aspect ratio, biocompatibility and low toxicity. In this study, HNTs were incorporated into the epoxy resin matrix to improve its mechanical properties and thermal stability. However, heterogeneous size, surface charge and surface hydrogen bond formation, result in aggregation of HNTs in epoxies to a certain extent. Three specific techniques were used to integrate HNTs into neat epoxy resin (NE). The structure and morphology of the embedded nanotubes were confirmed by Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). Tensile testing was carried out and the fractured surface of the tested specimen was analysed using scanning electron microscopy (SEM). The thermal stability of the prepared nanocomposite materials was investigated by thermogravimetric (TG) and derivative thermogravimetry (DTG) studies. The obtained results indicated that improved properties of HNTs/epoxy nanocomposite materials were related to the unique properties of well-dispersed HNTs, agglomerate scale, and reduced void presence, and could be controlled by the manufacturing processes.
PB  - Springer International Publishing
T2  - Experimental and Computational Investigations in Engineering
T1  - Effects of dispersion and particle-matrix interactions on mechanical and thermal properties of hnt/epoxy nanocomposite materials
SP  - 310
EP  - 325
DO  - 10.1007/978-3-030-58362-0_18
ER  - 

@inbook{
author = "Jelić, Aleksandra and Božić, Aleksandra and Stamenović, Marina and Sekulić, Milica and Porobić, Slavica and Dikić, Stefan and Putić, Slaviša and Mitrović, Nenad and Mladenović, Goran and Mitrović, Aleksandra",
year = "2021",
abstract = "Halloysite nanotubes (HNTs), naturally occurring as aluminosilicate nanoclay mineral, have recently emerged as a possible nanomaterial for countless applications due to their specific chemical structure, tubular shape, high aspect ratio, biocompatibility and low toxicity. In this study, HNTs were incorporated into the epoxy resin matrix to improve its mechanical properties and thermal stability. However, heterogeneous size, surface charge and surface hydrogen bond formation, result in aggregation of HNTs in epoxies to a certain extent. Three specific techniques were used to integrate HNTs into neat epoxy resin (NE). The structure and morphology of the embedded nanotubes were confirmed by Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). Tensile testing was carried out and the fractured surface of the tested specimen was analysed using scanning electron microscopy (SEM). The thermal stability of the prepared nanocomposite materials was investigated by thermogravimetric (TG) and derivative thermogravimetry (DTG) studies. The obtained results indicated that improved properties of HNTs/epoxy nanocomposite materials were related to the unique properties of well-dispersed HNTs, agglomerate scale, and reduced void presence, and could be controlled by the manufacturing processes.",
publisher = "Springer International Publishing",
journal = "Experimental and Computational Investigations in Engineering",
booktitle = "Effects of dispersion and particle-matrix interactions on mechanical and thermal properties of hnt/epoxy nanocomposite materials",
pages = "310-325",
doi = "10.1007/978-3-030-58362-0_18"
}

Jelić, A., Božić, A., Stamenović, M., Sekulić, M., Porobić, S., Dikić, S., Putić, S., Mitrović, N., Mladenović, G.,& Mitrović, A.. (2021). Effects of dispersion and particle-matrix interactions on mechanical and thermal properties of hnt/epoxy nanocomposite materials. in Experimental and Computational Investigations in Engineering
Springer International Publishing., 310-325.
https://doi.org/10.1007/978-3-030-58362-0_18

Jelić A, Božić A, Stamenović M, Sekulić M, Porobić S, Dikić S, Putić S, Mitrović N, Mladenović G, Mitrović A. Effects of dispersion and particle-matrix interactions on mechanical and thermal properties of hnt/epoxy nanocomposite materials. in Experimental and Computational Investigations in Engineering. 2021;:310-325.
doi:10.1007/978-3-030-58362-0_18 .

Jelić, Aleksandra, Božić, Aleksandra, Stamenović, Marina, Sekulić, Milica, Porobić, Slavica, Dikić, Stefan, Putić, Slaviša, Mitrović, Nenad, Mladenović, Goran, Mitrović, Aleksandra, "Effects of dispersion and particle-matrix interactions on mechanical and thermal properties of hnt/epoxy nanocomposite materials" in Experimental and Computational Investigations in Engineering (2021):310-325,
https://doi.org/10.1007/978-3-030-58362-0_18 . .

TY  - JOUR
AU  - Mališić, Vanja
AU  - Tomić, Nataša
AU  - Vuksanović, Marija M.
AU  - Balanc, Bojana
AU  - Stević, Zoran
AU  - Marinković, Aleksandar D.
AU  - Jančić-Heinemann, Radmila
AU  - Putić, Slaviša
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8923
AB  - Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat alumina particles (Al2O3) and alumina doped with iron oxide (Al2O3-Fe) modified with 3-aminopropyl-trimethoxylane (AM) and flax oil fatty acid methyl esters (biodiesel - BD) were used as reinforcement. Thermal conductivity measurements showed that composite with alumina particles with the highest alpha phase content had the highest thermal conductivity values. Mechanical properties (tensile strength, modulus of elasticity and elongation at break) were improved by the addition of modified alumina particles to PMMA/DMI matrix. The thermal properties are the most improved for composite with 3 wt.% Al2O3-Fe-AM particles that had the lowest temperature in a crack zone was noticed (10.28 %) compared to PMMA added due to the better stiffness and highest thermal conductivity.
T2  - Science of Sintering
T1  - An experimental study of mechanical properties and heat transfer of acrylic composites with structural and surface modified Al2O3 particles
VL  - 52
IS  - 4
SP  - 457
EP  - 467
DO  - 10.2298/SOS2004457M
ER  - 

@article{
author = "Mališić, Vanja and Tomić, Nataša and Vuksanović, Marija M. and Balanc, Bojana and Stević, Zoran and Marinković, Aleksandar D. and Jančić-Heinemann, Radmila and Putić, Slaviša",
year = "2020",
abstract = "Thermal properties of acrylate-based composite combined with alumina-based particles were investigated. The composites were made of poly (methyl methacrylate) (PMMA) modified with dimethyl itaconate (DMI) as a matrix. Neat alumina particles (Al2O3) and alumina doped with iron oxide (Al2O3-Fe) modified with 3-aminopropyl-trimethoxylane (AM) and flax oil fatty acid methyl esters (biodiesel - BD) were used as reinforcement. Thermal conductivity measurements showed that composite with alumina particles with the highest alpha phase content had the highest thermal conductivity values. Mechanical properties (tensile strength, modulus of elasticity and elongation at break) were improved by the addition of modified alumina particles to PMMA/DMI matrix. The thermal properties are the most improved for composite with 3 wt.% Al2O3-Fe-AM particles that had the lowest temperature in a crack zone was noticed (10.28 %) compared to PMMA added due to the better stiffness and highest thermal conductivity.",
journal = "Science of Sintering",
title = "An experimental study of mechanical properties and heat transfer of acrylic composites with structural and surface modified Al2O3 particles",
volume = "52",
number = "4",
pages = "457-467",
doi = "10.2298/SOS2004457M"
}

Mališić, V., Tomić, N., Vuksanović, M. M., Balanc, B., Stević, Z., Marinković, A. D., Jančić-Heinemann, R.,& Putić, S.. (2020). An experimental study of mechanical properties and heat transfer of acrylic composites with structural and surface modified Al2O3 particles. in Science of Sintering, 52(4), 457-467.
https://doi.org/10.2298/SOS2004457M

Mališić V, Tomić N, Vuksanović MM, Balanc B, Stević Z, Marinković AD, Jančić-Heinemann R, Putić S. An experimental study of mechanical properties and heat transfer of acrylic composites with structural and surface modified Al2O3 particles. in Science of Sintering. 2020;52(4):457-467.
doi:10.2298/SOS2004457M .

Mališić, Vanja, Tomić, Nataša, Vuksanović, Marija M., Balanc, Bojana, Stević, Zoran, Marinković, Aleksandar D., Jančić-Heinemann, Radmila, Putić, Slaviša, "An experimental study of mechanical properties and heat transfer of acrylic composites with structural and surface modified Al2O3 particles" in Science of Sintering, 52, no. 4 (2020):457-467,
https://doi.org/10.2298/SOS2004457M . .

TY  - JOUR
AU  - Vujčić, Ivica
AU  - Gavrilović, Tamara V.
AU  - Sekulić, Milica
AU  - Mašić, Slobodan
AU  - Putić, Slaviša S.
AU  - Papan, Jelena
AU  - Dramićanin, Miroslav
PY  - 2018
UR  - http://linkinghub.elsevier.com/retrieve/pii/S0168583X18301666
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7669
AB  - Eu3+ activated LaPO4 phosphors were prepared by a high-temperature solid-state method and irradiated to different high-doses gamma-radiation in the 0-4 MGy range. No effects of high-doses of high-energy radiation on phosphor's morphology and structure were observed, as documented by electron microscopy and X-ray diffraction measurements. On the other hand, photoluminescence measurements showed that emission properties of phosphor were affected by gamma-radiation; changes in radiative properties being prominent for absorbed radiation doses up to 250 kGy after which no additional changes are observed. Judd-Ofelt analysis of emission spectra is performed to thoroughly investigate radiative properties of phosphors. Analysis showed that radiative transition probability of Eu3+ emission decreases while non-radiative probability increases upon gamma-irradiation. Quantum efficiency of emission is decreased from about 46% to 35% when Eu3+ doped LaPO4 powders are exposed to gamma-radiation of 250 kGy dose, showing no additional decrease for higher gamma-radiation doses.
T2  - Nuclear Instruments and Methods in Physics Research. Section B: Beam Interactions with Materials and Atoms
T1  - Gamma-radiation effects on luminescence properties of Eu 3+ activated LaPO 4 phosphor
VL  - 422
SP  - 85
EP  - 90
DO  - 10.1016/j.nimb.2018.03.002
ER  - 

@article{
author = "Vujčić, Ivica and Gavrilović, Tamara V. and Sekulić, Milica and Mašić, Slobodan and Putić, Slaviša S. and Papan, Jelena and Dramićanin, Miroslav",
year = "2018",
abstract = "Eu3+ activated LaPO4 phosphors were prepared by a high-temperature solid-state method and irradiated to different high-doses gamma-radiation in the 0-4 MGy range. No effects of high-doses of high-energy radiation on phosphor's morphology and structure were observed, as documented by electron microscopy and X-ray diffraction measurements. On the other hand, photoluminescence measurements showed that emission properties of phosphor were affected by gamma-radiation; changes in radiative properties being prominent for absorbed radiation doses up to 250 kGy after which no additional changes are observed. Judd-Ofelt analysis of emission spectra is performed to thoroughly investigate radiative properties of phosphors. Analysis showed that radiative transition probability of Eu3+ emission decreases while non-radiative probability increases upon gamma-irradiation. Quantum efficiency of emission is decreased from about 46% to 35% when Eu3+ doped LaPO4 powders are exposed to gamma-radiation of 250 kGy dose, showing no additional decrease for higher gamma-radiation doses.",
journal = "Nuclear Instruments and Methods in Physics Research. Section B: Beam Interactions with Materials and Atoms",
title = "Gamma-radiation effects on luminescence properties of Eu 3+ activated LaPO 4 phosphor",
volume = "422",
pages = "85-90",
doi = "10.1016/j.nimb.2018.03.002"
}

Vujčić, I., Gavrilović, T. V., Sekulić, M., Mašić, S., Putić, S. S., Papan, J.,& Dramićanin, M.. (2018). Gamma-radiation effects on luminescence properties of Eu 3+ activated LaPO 4 phosphor. in Nuclear Instruments and Methods in Physics Research. Section B: Beam Interactions with Materials and Atoms, 422, 85-90.
https://doi.org/10.1016/j.nimb.2018.03.002

Vujčić I, Gavrilović TV, Sekulić M, Mašić S, Putić SS, Papan J, Dramićanin M. Gamma-radiation effects on luminescence properties of Eu 3+ activated LaPO 4 phosphor. in Nuclear Instruments and Methods in Physics Research. Section B: Beam Interactions with Materials and Atoms. 2018;422:85-90.
doi:10.1016/j.nimb.2018.03.002 .

Vujčić, Ivica, Gavrilović, Tamara V., Sekulić, Milica, Mašić, Slobodan, Putić, Slaviša S., Papan, Jelena, Dramićanin, Miroslav, "Gamma-radiation effects on luminescence properties of Eu 3+ activated LaPO 4 phosphor" in Nuclear Instruments and Methods in Physics Research. Section B: Beam Interactions with Materials and Atoms, 422 (2018):85-90,
https://doi.org/10.1016/j.nimb.2018.03.002 . .

TY  - JOUR
AU  - Dimić, Ivana 
AU  - Cvijović-Alagić, Ivana
AU  - Obradović, Nataša
AU  - Petrović, Jelena
AU  - Putić, Slaviša S.
AU  - Rakin, Marko P.
AU  - Bugarski, Branko M.
PY  - 2015
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/870
AB  - Metallic materials, such as Co-Cr-Mo alloys, are exposed to aggressive conditions in the oral cavity that represents an ideal environment for metallic ion release and biodegradation. The metallic ions released from dental materials can cause local and/or systemic adverse effects in the human body. Therefore, dental materials are required to possess appropriate mechanical, physical, chemical and biological properties. The biocompatibility of metallic materials is very important for dental applications. Accordingly, the aim of this study was to examine metallic ion release and cytotoxicity of Co-30Cr-5Mo cast alloy as the initial phase of biocompatibility evaluation. Determination of the viability of human (MRC-5) and animal (L929) fibroblast cells were conducted using three in vitro test methods: the colorimetric methyl-thiazol-tetrazolium (MTT) test, the dye exclusion test (DET) and the agar diffusion test (ADT). Furthermore, the morphology and growth of the cells were analyzed using scanning electron microscopy (SEM). The obtained results indicated that Co-30Cr-5Mo alloy did not release harmful elements in concentrations high enough to have detrimental effects on human and animal fibroblasts under the given experimental conditions. Moreover, the fibroblast cells showed good adhesion on the surface of the Co-30Cr-5Mo alloy. Therefore, it could be concluded that Co-30Cr-5Mo alloy is a biocompatible material that could be safely used in dentistry.
T2  - Journal of the Serbian Chemical Society
T1  - In vitro biocompatibility assessment of Co-Cr-Mo dental cast alloy
VL  - 80
IS  - 12
SP  - 1541
EP  - 1552
DO  - 10.2298/JSC150505070M
ER  - 

@article{
author = "Dimić, Ivana  and Cvijović-Alagić, Ivana and Obradović, Nataša and Petrović, Jelena and Putić, Slaviša S. and Rakin, Marko P. and Bugarski, Branko M.",
year = "2015",
abstract = "Metallic materials, such as Co-Cr-Mo alloys, are exposed to aggressive conditions in the oral cavity that represents an ideal environment for metallic ion release and biodegradation. The metallic ions released from dental materials can cause local and/or systemic adverse effects in the human body. Therefore, dental materials are required to possess appropriate mechanical, physical, chemical and biological properties. The biocompatibility of metallic materials is very important for dental applications. Accordingly, the aim of this study was to examine metallic ion release and cytotoxicity of Co-30Cr-5Mo cast alloy as the initial phase of biocompatibility evaluation. Determination of the viability of human (MRC-5) and animal (L929) fibroblast cells were conducted using three in vitro test methods: the colorimetric methyl-thiazol-tetrazolium (MTT) test, the dye exclusion test (DET) and the agar diffusion test (ADT). Furthermore, the morphology and growth of the cells were analyzed using scanning electron microscopy (SEM). The obtained results indicated that Co-30Cr-5Mo alloy did not release harmful elements in concentrations high enough to have detrimental effects on human and animal fibroblasts under the given experimental conditions. Moreover, the fibroblast cells showed good adhesion on the surface of the Co-30Cr-5Mo alloy. Therefore, it could be concluded that Co-30Cr-5Mo alloy is a biocompatible material that could be safely used in dentistry.",
journal = "Journal of the Serbian Chemical Society",
title = "In vitro biocompatibility assessment of Co-Cr-Mo dental cast alloy",
volume = "80",
number = "12",
pages = "1541-1552",
doi = "10.2298/JSC150505070M"
}

Dimić, I., Cvijović-Alagić, I., Obradović, N., Petrović, J., Putić, S. S., Rakin, M. P.,& Bugarski, B. M.. (2015). In vitro biocompatibility assessment of Co-Cr-Mo dental cast alloy. in Journal of the Serbian Chemical Society, 80(12), 1541-1552.
https://doi.org/10.2298/JSC150505070M

Dimić I, Cvijović-Alagić I, Obradović N, Petrović J, Putić SS, Rakin MP, Bugarski BM. In vitro biocompatibility assessment of Co-Cr-Mo dental cast alloy. in Journal of the Serbian Chemical Society. 2015;80(12):1541-1552.
doi:10.2298/JSC150505070M .

Dimić, Ivana , Cvijović-Alagić, Ivana, Obradović, Nataša, Petrović, Jelena, Putić, Slaviša S., Rakin, Marko P., Bugarski, Branko M., "In vitro biocompatibility assessment of Co-Cr-Mo dental cast alloy" in Journal of the Serbian Chemical Society, 80, no. 12 (2015):1541-1552,
https://doi.org/10.2298/JSC150505070M . .

TY  - JOUR
AU  - Dimić, Ivana 
AU  - Cvijović-Alagić, Ivana
AU  - Kostic, Ivana T.
AU  - Perić-Grujić, Aleksandra A.
AU  - Rakin, Marko P.
AU  - Putić, Slaviša S.
AU  - Bugarski, Branko M.
PY  - 2014
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/310
AB  - Metallic biomaterials, which are mainly used for the damaged hard tissue replacements, are materials with high strength, excellent toughness and good wear resistance. The disadvantages of metals as implant materials are their susceptibility to corrosion, the elastic modulus mismatch between metals and human hard tissues, relatively high density and metallic ion release, which can cause serious health problems. The aim of this study was to examine metallic ion release from Co-Cr-Mo alloy in artificial saliva. In that purpose, alloy samples were immersed into artificial saliva with different pH values (4.0, 5.5 and 7.5). After a certain immersion period (1, 3 and 6 weeks) the concentrations of released ions were determined using inductively coupled plasma-mass spectrometry (ICP-MS). The research findings were used in order to define the dependence between the concentration of released metallic ions, artificial saliva pH values and immersion time. The determined released metallic ions concentrations were compared with literature data in order to describe and better understand the phenomenon of metallic ion release from the biocom-patible cobalt-based alloy.
AB  - Metalni biomaterijali, koji se najčešće koriste za zamenu oštećenih čvrstih tkiva u organizmu čoveka, su materijali velike čvrstoće, žilavosti i otpornosti prema habanju. Nedostaci metala, kao implantnih materijala, su njihova podložnost koroziji, neusklađenost modula elastičnosti metala i čvrstih ljudskih tkiva, velika gustina i otpuštanje metalnih jona koje može da izazove ozbiljne zdravstvene probleme. Cilj ovog rada je bio da se ispita otpuštanje metalnih jona iz Co-Cr-Mo legure u rastvoru veštačke pljuvačke. Uzorci legure su potopljeni u rastvor veštačke pljuvačke različite pH vrednosti (4,0, 5,5 i 7,5). Nakon određenog vremena izlaganja legure veštačkoj pljuvačci (1, 3 i 6 nedelja) određene su koncentracije otpuštenih jona primenom indukcije spregnute plazme sa masenom spektrometrijom (ICP-MS). Dobijeni rezultati su iskorišćeni u cilju definisanja zavisnosti između koncentracije otpuštenih jona, pH vrednosti veštačke pljuvačke i dužine potapanja legure u rastvor veštačke pljuvačke. Osim toga, utvrđene koncentracije otpuštenih metalnih jona iz ispitivane legure su upoređene sa podacima dostupnim u literaturi u cilju što boljeg opisivanja i razumevanja fenomena otpuštanja metalnih jona iz biokompatibilne Co-Cr-Mo legure.
T2  - Chemical Industry and Chemical Engineering Quarterly / CICEQ
T1  - Metallic Ion Release from Biocompatible Cobalt-Based Alloy
VL  - 20
IS  - 4
SP  - 571
EP  - 577
DO  - 10.2298/CICEQ130813039D
ER  - 

@article{
author = "Dimić, Ivana  and Cvijović-Alagić, Ivana and Kostic, Ivana T. and Perić-Grujić, Aleksandra A. and Rakin, Marko P. and Putić, Slaviša S. and Bugarski, Branko M.",
year = "2014",
abstract = "Metallic biomaterials, which are mainly used for the damaged hard tissue replacements, are materials with high strength, excellent toughness and good wear resistance. The disadvantages of metals as implant materials are their susceptibility to corrosion, the elastic modulus mismatch between metals and human hard tissues, relatively high density and metallic ion release, which can cause serious health problems. The aim of this study was to examine metallic ion release from Co-Cr-Mo alloy in artificial saliva. In that purpose, alloy samples were immersed into artificial saliva with different pH values (4.0, 5.5 and 7.5). After a certain immersion period (1, 3 and 6 weeks) the concentrations of released ions were determined using inductively coupled plasma-mass spectrometry (ICP-MS). The research findings were used in order to define the dependence between the concentration of released metallic ions, artificial saliva pH values and immersion time. The determined released metallic ions concentrations were compared with literature data in order to describe and better understand the phenomenon of metallic ion release from the biocom-patible cobalt-based alloy., Metalni biomaterijali, koji se najčešće koriste za zamenu oštećenih čvrstih tkiva u organizmu čoveka, su materijali velike čvrstoće, žilavosti i otpornosti prema habanju. Nedostaci metala, kao implantnih materijala, su njihova podložnost koroziji, neusklađenost modula elastičnosti metala i čvrstih ljudskih tkiva, velika gustina i otpuštanje metalnih jona koje može da izazove ozbiljne zdravstvene probleme. Cilj ovog rada je bio da se ispita otpuštanje metalnih jona iz Co-Cr-Mo legure u rastvoru veštačke pljuvačke. Uzorci legure su potopljeni u rastvor veštačke pljuvačke različite pH vrednosti (4,0, 5,5 i 7,5). Nakon određenog vremena izlaganja legure veštačkoj pljuvačci (1, 3 i 6 nedelja) određene su koncentracije otpuštenih jona primenom indukcije spregnute plazme sa masenom spektrometrijom (ICP-MS). Dobijeni rezultati su iskorišćeni u cilju definisanja zavisnosti između koncentracije otpuštenih jona, pH vrednosti veštačke pljuvačke i dužine potapanja legure u rastvor veštačke pljuvačke. Osim toga, utvrđene koncentracije otpuštenih metalnih jona iz ispitivane legure su upoređene sa podacima dostupnim u literaturi u cilju što boljeg opisivanja i razumevanja fenomena otpuštanja metalnih jona iz biokompatibilne Co-Cr-Mo legure.",
journal = "Chemical Industry and Chemical Engineering Quarterly / CICEQ",
title = "Metallic Ion Release from Biocompatible Cobalt-Based Alloy",
volume = "20",
number = "4",
pages = "571-577",
doi = "10.2298/CICEQ130813039D"
}

Dimić, I., Cvijović-Alagić, I., Kostic, I. T., Perić-Grujić, A. A., Rakin, M. P., Putić, S. S.,& Bugarski, B. M.. (2014). Metallic Ion Release from Biocompatible Cobalt-Based Alloy. in Chemical Industry and Chemical Engineering Quarterly / CICEQ, 20(4), 571-577.
https://doi.org/10.2298/CICEQ130813039D

Dimić I, Cvijović-Alagić I, Kostic IT, Perić-Grujić AA, Rakin MP, Putić SS, Bugarski BM. Metallic Ion Release from Biocompatible Cobalt-Based Alloy. in Chemical Industry and Chemical Engineering Quarterly / CICEQ. 2014;20(4):571-577.
doi:10.2298/CICEQ130813039D .

Dimić, Ivana , Cvijović-Alagić, Ivana, Kostic, Ivana T., Perić-Grujić, Aleksandra A., Rakin, Marko P., Putić, Slaviša S., Bugarski, Branko M., "Metallic Ion Release from Biocompatible Cobalt-Based Alloy" in Chemical Industry and Chemical Engineering Quarterly / CICEQ, 20, no. 4 (2014):571-577,
https://doi.org/10.2298/CICEQ130813039D . .