TY  - JOUR
AU  - Nešić, Aleksandra
AU  - Kokunešoski, Maja
AU  - Meseldžija, Slađana
AU  - Volkov-Husović, Tatjana
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/12664
AB  - The textile industry is one of the largest water-consuming industries in the world. The wastewater generated by the textile industry is a major source of pollution, containing mostly dyes, but also detergents, and heavy metals. Since dyes can have a negative impact on the environment, human and aquatic life, it is really important to find proper solutions for removal of these pollutants from wastewater. In addition, special attention is given to the discovery of new and fast "in situ" methods for identification and quantification of pollutants from wastewater. In this paper, SBA-15, mesoporous silica material, was used as sorbent for removal of Basic Yellow 28 from aqueous solutions. In addition, colored SBA-15 after sorption process was subjected to image analysis, to evaluate if it was possible to quantify sorbed dye on sorbent based on intensity of SBA-15 coloration. The obtained results revealed that SBA-15 could remove 99% of dye within 5 min. The highest efficiency of dye removal was at pH8, using 200 mg of sorbent. According to the Langmuir isotherm model, the theoretical maximum sorption capacity was 909 mg/g. Image-Pro software confirmed that it would be possible to quantify sorbed dye onto SBA-15 with accuracy of 0.98. Overall, SBA-15 demonstrated to be efficient sorbent in removal of Basic Yellow 28 from water, but also to be potential carrier as a sensor for detection of colored pollutants in water.
AB  - Tekstilna industrija je jedna od najvećih potrošača vode u odnosu na druge industrijske grane. Otpadne vode iz tekstilne industrije su jedan od glavnih izvora zagađenja i uglavnom sadrže boje, ali takođe i deterdžente i teške metale. Pošto boje mogu imati negativan uticaj na životnu sredinu, ljude i vodeni svet, važno je pronaći odgovarajuća rešenja za uklanjanje ovih zagađivača iz otpadnih voda. Pored toga, posebna pažnja je posvećena otkrivanju novih i brzih „in situ” metoda za identifikaciju i kvantifikaciju zagađivača iz otpadnih voda. U ovom radu kao sorbent za uklanjanje Basic Yellow 28 boje iz vodenih rastvora korišćen je SBA-15, mezoporozni silika materijal. Pored toga, obojeni SBA-15 nakon procesa sorpcije podvrgnuti su analizi slike, kako bi se procenilo da li je moguće kvantifikovati sorbovanu boju na sorbentu na osnovu intenziteta obojenosti SBA-15. Dobijeni rezultati su pokazali da SBA-15 može ukloniti 99% boje u roku od 5 minuta. Najveća efikasnost uklanjanja boje bila je pri pH 8, korišćenjem 200 mg sorbenta. Prema Langmuirovom modelu, teoretski maksimalni kapacitet sorpcije bio je 909 mg/g. Softver Image-Pro je potvrdio da je moguće kvantifikovati boju na SBA-15 sa tačnošću od 0,98. SBA-15 se pokazao kao efikasan sorbent u uklanjanju Basic Yellow 28 boje iz vode, ali i kao potencijalni senzor za detekciju obojenih zagađivača u vodi.
T2  - Advanced Technologies
T1  - Mesoporous silica-based sensor for colorimetric determination of Basic Yellow 28 dye in aqueous solutions
T1  - Senzor na bazi mezoporozne silike za kolorimetrijsko određivanje boje Basic Yellow 28 u vodenim rastvorima
VL  - 12
IS  - 2
SP  - 37
EP  - 42
DO  - 10.5937/savteh2302036N
ER  - 

@article{
author = "Nešić, Aleksandra and Kokunešoski, Maja and Meseldžija, Slađana and Volkov-Husović, Tatjana",
year = "2023",
abstract = "The textile industry is one of the largest water-consuming industries in the world. The wastewater generated by the textile industry is a major source of pollution, containing mostly dyes, but also detergents, and heavy metals. Since dyes can have a negative impact on the environment, human and aquatic life, it is really important to find proper solutions for removal of these pollutants from wastewater. In addition, special attention is given to the discovery of new and fast "in situ" methods for identification and quantification of pollutants from wastewater. In this paper, SBA-15, mesoporous silica material, was used as sorbent for removal of Basic Yellow 28 from aqueous solutions. In addition, colored SBA-15 after sorption process was subjected to image analysis, to evaluate if it was possible to quantify sorbed dye on sorbent based on intensity of SBA-15 coloration. The obtained results revealed that SBA-15 could remove 99% of dye within 5 min. The highest efficiency of dye removal was at pH8, using 200 mg of sorbent. According to the Langmuir isotherm model, the theoretical maximum sorption capacity was 909 mg/g. Image-Pro software confirmed that it would be possible to quantify sorbed dye onto SBA-15 with accuracy of 0.98. Overall, SBA-15 demonstrated to be efficient sorbent in removal of Basic Yellow 28 from water, but also to be potential carrier as a sensor for detection of colored pollutants in water., Tekstilna industrija je jedna od najvećih potrošača vode u odnosu na druge industrijske grane. Otpadne vode iz tekstilne industrije su jedan od glavnih izvora zagađenja i uglavnom sadrže boje, ali takođe i deterdžente i teške metale. Pošto boje mogu imati negativan uticaj na životnu sredinu, ljude i vodeni svet, važno je pronaći odgovarajuća rešenja za uklanjanje ovih zagađivača iz otpadnih voda. Pored toga, posebna pažnja je posvećena otkrivanju novih i brzih „in situ” metoda za identifikaciju i kvantifikaciju zagađivača iz otpadnih voda. U ovom radu kao sorbent za uklanjanje Basic Yellow 28 boje iz vodenih rastvora korišćen je SBA-15, mezoporozni silika materijal. Pored toga, obojeni SBA-15 nakon procesa sorpcije podvrgnuti su analizi slike, kako bi se procenilo da li je moguće kvantifikovati sorbovanu boju na sorbentu na osnovu intenziteta obojenosti SBA-15. Dobijeni rezultati su pokazali da SBA-15 može ukloniti 99% boje u roku od 5 minuta. Najveća efikasnost uklanjanja boje bila je pri pH 8, korišćenjem 200 mg sorbenta. Prema Langmuirovom modelu, teoretski maksimalni kapacitet sorpcije bio je 909 mg/g. Softver Image-Pro je potvrdio da je moguće kvantifikovati boju na SBA-15 sa tačnošću od 0,98. SBA-15 se pokazao kao efikasan sorbent u uklanjanju Basic Yellow 28 boje iz vode, ali i kao potencijalni senzor za detekciju obojenih zagađivača u vodi.",
journal = "Advanced Technologies",
title = "Mesoporous silica-based sensor for colorimetric determination of Basic Yellow 28 dye in aqueous solutions, Senzor na bazi mezoporozne silike za kolorimetrijsko određivanje boje Basic Yellow 28 u vodenim rastvorima",
volume = "12",
number = "2",
pages = "37-42",
doi = "10.5937/savteh2302036N"
}

Nešić, A., Kokunešoski, M., Meseldžija, S.,& Volkov-Husović, T.. (2023). Mesoporous silica-based sensor for colorimetric determination of Basic Yellow 28 dye in aqueous solutions. in Advanced Technologies, 12(2), 37-42.
https://doi.org/10.5937/savteh2302036N

Nešić A, Kokunešoski M, Meseldžija S, Volkov-Husović T. Mesoporous silica-based sensor for colorimetric determination of Basic Yellow 28 dye in aqueous solutions. in Advanced Technologies. 2023;12(2):37-42.
doi:10.5937/savteh2302036N .

Nešić, Aleksandra, Kokunešoski, Maja, Meseldžija, Slađana, Volkov-Husović, Tatjana, "Mesoporous silica-based sensor for colorimetric determination of Basic Yellow 28 dye in aqueous solutions" in Advanced Technologies, 12, no. 2 (2023):37-42,
https://doi.org/10.5937/savteh2302036N . .

TY  - JOUR
AU  - Vlahović, Milica
AU  - Alil, Ana
AU  - Devečerski, Aleksandar
AU  - Živojinović, Dragana
AU  - Volkov Husović, Tatjana
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/11462
AB  - In many industrial processes that include fluid flow, cavitation erosion of different engineeringstructures (pumps, turbines, water levels, valves, etc.) during their operation is expected. Metallic,ceramic, and composite materials are usual candidates considered for application in such extremeconditions. In this study, the idea is to synthesize refractory ceramic material based on talc withthe addition of zeolite for utilization as protective coatings in cavitating conditions. Two talc-basedrefractories with zeolites from two Serbian deposits were produced. The behaviors of the samplesin simulated cavitation conditions were examined by an advanced non-destructive methodologyconsisting of monitoring mass loss and surface degradation using image analysis compiled withprincipal component analysis (PCA), interior degradation by ultrasonic measurements, and themicrostructure by a scanning electron microscope (SEM). Lower mass loss, surface degradation level,and modeled strength decrease indicated better cavitation resistance of the sample with Igros zeolite,whereby measured strength values validated the model. For the chosen critical strength, the criticalcavitation period as well as critical morphological descriptors, Area and Diameter (max and min),were determined. A Young’s elasticity modulus decrease indicated that surface damage influenceprogressed towards interior of the material. It can be concluded that the proposed methodologyapproach is efficient and reliable in predicting the materials’ service life in extreme conditions.
T2  - Materials
T1  - Non-Destructive Examination for Cavitation Resistance of Talc-Based Refractories with Different Zeolite Types Intended for Protective Coatings
VL  - 16
IS  - 16
SP  - 5577
DO  - 10.3390/ma16165577
ER  - 

@article{
author = "Vlahović, Milica and Alil, Ana and Devečerski, Aleksandar and Živojinović, Dragana and Volkov Husović, Tatjana",
year = "2023",
abstract = "In many industrial processes that include fluid flow, cavitation erosion of different engineeringstructures (pumps, turbines, water levels, valves, etc.) during their operation is expected. Metallic,ceramic, and composite materials are usual candidates considered for application in such extremeconditions. In this study, the idea is to synthesize refractory ceramic material based on talc withthe addition of zeolite for utilization as protective coatings in cavitating conditions. Two talc-basedrefractories with zeolites from two Serbian deposits were produced. The behaviors of the samplesin simulated cavitation conditions were examined by an advanced non-destructive methodologyconsisting of monitoring mass loss and surface degradation using image analysis compiled withprincipal component analysis (PCA), interior degradation by ultrasonic measurements, and themicrostructure by a scanning electron microscope (SEM). Lower mass loss, surface degradation level,and modeled strength decrease indicated better cavitation resistance of the sample with Igros zeolite,whereby measured strength values validated the model. For the chosen critical strength, the criticalcavitation period as well as critical morphological descriptors, Area and Diameter (max and min),were determined. A Young’s elasticity modulus decrease indicated that surface damage influenceprogressed towards interior of the material. It can be concluded that the proposed methodologyapproach is efficient and reliable in predicting the materials’ service life in extreme conditions.",
journal = "Materials",
title = "Non-Destructive Examination for Cavitation Resistance of Talc-Based Refractories with Different Zeolite Types Intended for Protective Coatings",
volume = "16",
number = "16",
pages = "5577",
doi = "10.3390/ma16165577"
}

Vlahović, M., Alil, A., Devečerski, A., Živojinović, D.,& Volkov Husović, T.. (2023). Non-Destructive Examination for Cavitation Resistance of Talc-Based Refractories with Different Zeolite Types Intended for Protective Coatings. in Materials, 16(16), 5577.
https://doi.org/10.3390/ma16165577

Vlahović M, Alil A, Devečerski A, Živojinović D, Volkov Husović T. Non-Destructive Examination for Cavitation Resistance of Talc-Based Refractories with Different Zeolite Types Intended for Protective Coatings. in Materials. 2023;16(16):5577.
doi:10.3390/ma16165577 .

Vlahović, Milica, Alil, Ana, Devečerski, Aleksandar, Živojinović, Dragana, Volkov Husović, Tatjana, "Non-Destructive Examination for Cavitation Resistance of Talc-Based Refractories with Different Zeolite Types Intended for Protective Coatings" in Materials, 16, no. 16 (2023):5577,
https://doi.org/10.3390/ma16165577 . .

TY  - JOUR
AU  - Perišić, Srđan
AU  - Kareem Ali Alzaroug, Azdihar
AU  - Kalevski, Katarina
AU  - Vuksanović, Marija M.
AU  - Volkov-Husović, Tatjana
AU  - Radović, Ivana M.
AU  - Radojević, Vesna
PY  - 2022
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10053
AB  - Polymer matrix composite materials have found application in dentistry because of good mechanical properties, aesthetic, easy processing, and possibilities of the repair. Acrylates are materials used to make and repair dentures. Reinforcements in the form of short glass or polymer fibers are added to improve the mechanical properties of dental polymers. In this study, the processing of composite material with a polymer matrix from commercial auto-polymerized acrylate Simgal, with reinforcement in the form of short poly(ethylene terephthalate) (PET) fibers was examined. Samples were processed in three series: pure Simgal, Simgal/PET 1 wt% and Simgal/PET 3 wt%. The influence of the reinforcement in the form of short PET fibers on the mechanical properties of composite materials was investigated. Strength and hardness were tested by impact testing and Vickers microhardness, and it was shown that there is an increase in absorbed energy and hardness. The modulus was reduced by the addition of PET fibers and by increasing the amount of fibers in the composite. The increase in the amount of PET fibers also resulted in a smaller loss of surface mass of the samples compared to the pure matrix by 63% and 93%, respectively. Cavitation test revealed better cavitation resistance of composites than the pure acrylate.
T2  - Polymer Composites
T1  - Denture composite reinforced with short polyethylene terephthalate fibers
IS  - 1
SP  - 543
EP  - 550
DO  - 10.1002/pc.26397
ER  - 

@article{
author = "Perišić, Srđan and Kareem Ali Alzaroug, Azdihar and Kalevski, Katarina and Vuksanović, Marija M. and Volkov-Husović, Tatjana and Radović, Ivana M. and Radojević, Vesna",
year = "2022",
abstract = "Polymer matrix composite materials have found application in dentistry because of good mechanical properties, aesthetic, easy processing, and possibilities of the repair. Acrylates are materials used to make and repair dentures. Reinforcements in the form of short glass or polymer fibers are added to improve the mechanical properties of dental polymers. In this study, the processing of composite material with a polymer matrix from commercial auto-polymerized acrylate Simgal, with reinforcement in the form of short poly(ethylene terephthalate) (PET) fibers was examined. Samples were processed in three series: pure Simgal, Simgal/PET 1 wt% and Simgal/PET 3 wt%. The influence of the reinforcement in the form of short PET fibers on the mechanical properties of composite materials was investigated. Strength and hardness were tested by impact testing and Vickers microhardness, and it was shown that there is an increase in absorbed energy and hardness. The modulus was reduced by the addition of PET fibers and by increasing the amount of fibers in the composite. The increase in the amount of PET fibers also resulted in a smaller loss of surface mass of the samples compared to the pure matrix by 63% and 93%, respectively. Cavitation test revealed better cavitation resistance of composites than the pure acrylate.",
journal = "Polymer Composites",
title = "Denture composite reinforced with short polyethylene terephthalate fibers",
number = "1",
pages = "543-550",
doi = "10.1002/pc.26397"
}

Perišić, S., Kareem Ali Alzaroug, A., Kalevski, K., Vuksanović, M. M., Volkov-Husović, T., Radović, I. M.,& Radojević, V.. (2022). Denture composite reinforced with short polyethylene terephthalate fibers. in Polymer Composites(1), 543-550.
https://doi.org/10.1002/pc.26397

Perišić S, Kareem Ali Alzaroug A, Kalevski K, Vuksanović MM, Volkov-Husović T, Radović IM, Radojević V. Denture composite reinforced with short polyethylene terephthalate fibers. in Polymer Composites. 2022;(1):543-550.
doi:10.1002/pc.26397 .

Perišić, Srđan, Kareem Ali Alzaroug, Azdihar, Kalevski, Katarina, Vuksanović, Marija M., Volkov-Husović, Tatjana, Radović, Ivana M., Radojević, Vesna, "Denture composite reinforced with short polyethylene terephthalate fibers" in Polymer Composites, no. 1 (2022):543-550,
https://doi.org/10.1002/pc.26397 . .

TY  - CONF
AU  - Simić, Marko
AU  - Ružić, Jovana
AU  - Luković, Jelena
AU  - Božić, Dušan
AU  - Alil, Ana
AU  - Volkov Husović, Tatjana
AU  - Stašić, Jelena
PY  - 2022
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/12093
AB  - Ternary Cu-2.71Zr-2.27B (wt.%) alloys were fabricated using powder metallurgy, i.e., mechanical alloying followed by cold pressing and sintering. Influence of the mechanical alloying parameters on microstructural and morphological changes of Cu-Zr-B powder mixture was investigated using scanning electron microscopy and X-ray diffraction. Stereological analysis was employed to determine changes in size and shape of copper particles during 40 hours of mechanical alloying. It was shown that with an increase in mechanical alloying time, the size of copper powder decreases. Williamson-Hall analysis was used to calculate crystallite sizes (D, nm), lattice parameter (nm), lattice strain (ε, %), and dislocation density (ρ, m-2). It was shown that with increasing mechanical allo ying time, lattice parameter as well as lattice strain both increases. Particles undergo high forces through ball-particle-ball and wall-particle-ball collisions during mechanical alloying. These collisions induce accumulation of dislocations in copper matrix and a decreasing in its crystallite size due to dominant plastic deformation mechanisms. Dislocation densities reach its maximum value at around 30 hours of mechanical alloying, after which they decrease owing to the recrystallization of copper matrix.
PB  - Beograd : Institut za istraživanja i projektovanja u privredi
C3  - YOURS 2022 : YOUng researcheRS conference 2022 : Book of abstracts
T1  - X-Ray analysis by Williamson-Hall and stereological analysis of mechanically alloyed Cu-Zr-B alloys
SP  - 13
EP  - 13
UR  - https://hdl.handle.net/21.15107/rcub_vinar_12093
ER  - 

@conference{
author = "Simić, Marko and Ružić, Jovana and Luković, Jelena and Božić, Dušan and Alil, Ana and Volkov Husović, Tatjana and Stašić, Jelena",
year = "2022",
abstract = "Ternary Cu-2.71Zr-2.27B (wt.%) alloys were fabricated using powder metallurgy, i.e., mechanical alloying followed by cold pressing and sintering. Influence of the mechanical alloying parameters on microstructural and morphological changes of Cu-Zr-B powder mixture was investigated using scanning electron microscopy and X-ray diffraction. Stereological analysis was employed to determine changes in size and shape of copper particles during 40 hours of mechanical alloying. It was shown that with an increase in mechanical alloying time, the size of copper powder decreases. Williamson-Hall analysis was used to calculate crystallite sizes (D, nm), lattice parameter (nm), lattice strain (ε, %), and dislocation density (ρ, m-2). It was shown that with increasing mechanical allo ying time, lattice parameter as well as lattice strain both increases. Particles undergo high forces through ball-particle-ball and wall-particle-ball collisions during mechanical alloying. These collisions induce accumulation of dislocations in copper matrix and a decreasing in its crystallite size due to dominant plastic deformation mechanisms. Dislocation densities reach its maximum value at around 30 hours of mechanical alloying, after which they decrease owing to the recrystallization of copper matrix.",
publisher = "Beograd : Institut za istraživanja i projektovanja u privredi",
journal = "YOURS 2022 : YOUng researcheRS conference 2022 : Book of abstracts",
title = "X-Ray analysis by Williamson-Hall and stereological analysis of mechanically alloyed Cu-Zr-B alloys",
pages = "13-13",
url = "https://hdl.handle.net/21.15107/rcub_vinar_12093"
}

Simić, M., Ružić, J., Luković, J., Božić, D., Alil, A., Volkov Husović, T.,& Stašić, J.. (2022). X-Ray analysis by Williamson-Hall and stereological analysis of mechanically alloyed Cu-Zr-B alloys. in YOURS 2022 : YOUng researcheRS conference 2022 : Book of abstracts
Beograd : Institut za istraživanja i projektovanja u privredi., 13-13.
https://hdl.handle.net/21.15107/rcub_vinar_12093

Simić M, Ružić J, Luković J, Božić D, Alil A, Volkov Husović T, Stašić J. X-Ray analysis by Williamson-Hall and stereological analysis of mechanically alloyed Cu-Zr-B alloys. in YOURS 2022 : YOUng researcheRS conference 2022 : Book of abstracts. 2022;:13-13.
https://hdl.handle.net/21.15107/rcub_vinar_12093 .

Simić, Marko, Ružić, Jovana, Luković, Jelena, Božić, Dušan, Alil, Ana, Volkov Husović, Tatjana, Stašić, Jelena, "X-Ray analysis by Williamson-Hall and stereological analysis of mechanically alloyed Cu-Zr-B alloys" in YOURS 2022 : YOUng researcheRS conference 2022 : Book of abstracts (2022):13-13,
https://hdl.handle.net/21.15107/rcub_vinar_12093 .

TY  - JOUR
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Gajić-Kvaščev, Maja
AU  - Vuksanović, Marija M.
AU  - Glišić, Dragomir
AU  - Volkov-Husović, Tatjana
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9935
AB  - Pattern recognition techniques are applied to various morphological descriptors to monitor the formation and propagation of surface defects of materials subjected to thermal shock. A low-cement high-alumina castable was synthesized, cured, sintered, and exposed to thermal stability testing using the water quench test. After a certain number of thermal shock cycles, photographs of the samples’ surfaces were taken and subjected to image analysis. The influence of the sintering temperature on the morphology of the detected defects was studied using principal component analysis (PCA) as a pattern recognition technique that is the most informative for extracting possible differences. The morphological descriptors of the defects correspond to the previous results regarding the influence of sintering temperature on the structure of a castable during thermal shocks.
T2  - Journal of the European Ceramic Society
T1  - Principal component analysis of morphological descriptors for monitoring surface defects induced by thermal shock
VL  - 41
SP  - 423
EP  - 429
DO  - 10.1016/j.jeurceramsoc.2021.08.058
ER  - 

@article{
author = "Martinović, Sanja and Vlahović, Milica and Gajić-Kvaščev, Maja and Vuksanović, Marija M. and Glišić, Dragomir and Volkov-Husović, Tatjana",
year = "2021",
abstract = "Pattern recognition techniques are applied to various morphological descriptors to monitor the formation and propagation of surface defects of materials subjected to thermal shock. A low-cement high-alumina castable was synthesized, cured, sintered, and exposed to thermal stability testing using the water quench test. After a certain number of thermal shock cycles, photographs of the samples’ surfaces were taken and subjected to image analysis. The influence of the sintering temperature on the morphology of the detected defects was studied using principal component analysis (PCA) as a pattern recognition technique that is the most informative for extracting possible differences. The morphological descriptors of the defects correspond to the previous results regarding the influence of sintering temperature on the structure of a castable during thermal shocks.",
journal = "Journal of the European Ceramic Society",
title = "Principal component analysis of morphological descriptors for monitoring surface defects induced by thermal shock",
volume = "41",
pages = "423-429",
doi = "10.1016/j.jeurceramsoc.2021.08.058"
}

Martinović, S., Vlahović, M., Gajić-Kvaščev, M., Vuksanović, M. M., Glišić, D.,& Volkov-Husović, T.. (2021). Principal component analysis of morphological descriptors for monitoring surface defects induced by thermal shock. in Journal of the European Ceramic Society, 41, 423-429.
https://doi.org/10.1016/j.jeurceramsoc.2021.08.058

Martinović S, Vlahović M, Gajić-Kvaščev M, Vuksanović MM, Glišić D, Volkov-Husović T. Principal component analysis of morphological descriptors for monitoring surface defects induced by thermal shock. in Journal of the European Ceramic Society. 2021;41:423-429.
doi:10.1016/j.jeurceramsoc.2021.08.058 .

Martinović, Sanja, Vlahović, Milica, Gajić-Kvaščev, Maja, Vuksanović, Marija M., Glišić, Dragomir, Volkov-Husović, Tatjana, "Principal component analysis of morphological descriptors for monitoring surface defects induced by thermal shock" in Journal of the European Ceramic Society, 41 (2021):423-429,
https://doi.org/10.1016/j.jeurceramsoc.2021.08.058 . .

TY  - JOUR
AU  - Obradović, Vera
AU  - Vuksanović, Marija M.
AU  - Tomić, Nataša
AU  - Stojanović, Dušica
AU  - Volkov-Husović, Tatjana
AU  - Uskoković, Petar
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/13116
AB  - In this study poly (vinyl butyral)/silica (PVB/SiO2) composite films were subjected to the cavitation process. The experiments were carried out with a 10 wt.% PVB solution in ethanol. Silica nanoparticles were added into the solution in different concentration of 1, 3 and 5 wt.% SiO2 in regard to PVB. Composite films were cast from these solutions and subjected to ultrasonic cavitation. Optical images of their surfaces were analyzed before and after cavitation, by Image-Pro Plus software. The results revealed that the PVB film with 5 wt.% SiO2 nanoparticles demonstrated the greatest improvement in microhardness with the best cavitation resistance compared to other films.
T2  - Polymers & Polymer Composites
T1  - Improvement in cavitation resistance of poly (vinyl butyral) composite films with silica nanoparticles: A technical note
VL  - 29
IS  - 9_SUPPL
SP  - S1664
EP  - S1669
DO  - 10.1177/0967391120986505
ER  - 

@article{
author = "Obradović, Vera and Vuksanović, Marija M. and Tomić, Nataša and Stojanović, Dušica and Volkov-Husović, Tatjana and Uskoković, Petar",
year = "2021",
abstract = "In this study poly (vinyl butyral)/silica (PVB/SiO2) composite films were subjected to the cavitation process. The experiments were carried out with a 10 wt.% PVB solution in ethanol. Silica nanoparticles were added into the solution in different concentration of 1, 3 and 5 wt.% SiO2 in regard to PVB. Composite films were cast from these solutions and subjected to ultrasonic cavitation. Optical images of their surfaces were analyzed before and after cavitation, by Image-Pro Plus software. The results revealed that the PVB film with 5 wt.% SiO2 nanoparticles demonstrated the greatest improvement in microhardness with the best cavitation resistance compared to other films.",
journal = "Polymers & Polymer Composites",
title = "Improvement in cavitation resistance of poly (vinyl butyral) composite films with silica nanoparticles: A technical note",
volume = "29",
number = "9_SUPPL",
pages = "S1664-S1669",
doi = "10.1177/0967391120986505"
}

Obradović, V., Vuksanović, M. M., Tomić, N., Stojanović, D., Volkov-Husović, T.,& Uskoković, P.. (2021). Improvement in cavitation resistance of poly (vinyl butyral) composite films with silica nanoparticles: A technical note. in Polymers & Polymer Composites, 29(9_SUPPL), S1664-S1669.
https://doi.org/10.1177/0967391120986505

Obradović V, Vuksanović MM, Tomić N, Stojanović D, Volkov-Husović T, Uskoković P. Improvement in cavitation resistance of poly (vinyl butyral) composite films with silica nanoparticles: A technical note. in Polymers & Polymer Composites. 2021;29(9_SUPPL):S1664-S1669.
doi:10.1177/0967391120986505 .

Obradović, Vera, Vuksanović, Marija M., Tomić, Nataša, Stojanović, Dušica, Volkov-Husović, Tatjana, Uskoković, Petar, "Improvement in cavitation resistance of poly (vinyl butyral) composite films with silica nanoparticles: A technical note" in Polymers & Polymer Composites, 29, no. 9_SUPPL (2021):S1664-S1669,
https://doi.org/10.1177/0967391120986505 . .

TY  - JOUR
AU  - Vuksanović, Marija M.
AU  - Gajić-Kvaščev, Maja
AU  - Volkov-Husović, Tatjana
AU  - Jančić-Heinemann, Radmila
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9162
AB  - Morphology and development of surface damage of alumina-based materials, resulting from cavitation erosion is studied in this paper. Two series of samples were prepared: samples without fibers and those with the addition of 2 wt % of ceramic fibers. The form of surface damage is considered to be the information carrier for the analysis of the resistance of materials to cavitation and the quality of this information is determined. The surface of the samples was monitored in defined time intervals in order to prepare the digitized image suitable for further analysis using image analysis software. The principal component analysis was applied to examine the appearance of certain morphological characteristics depending on the behavior of the material during cavitation erosion. It was concluded that the addition of ceramic fibers gained in importance after a long time of cavitation erosion, while during a starting period of time the difference in the morphology of the damage is not very observable. © 2021 Elsevier B.V.
T2  - Wear
T1  - Advanced damage resistance monitoring procedure on the composite materials’ surface-exposed to cavitation testing
VL  - 474-475
SP  - 203877
DO  - 10.1016/j.wear.2021.203877
ER  - 

@article{
author = "Vuksanović, Marija M. and Gajić-Kvaščev, Maja and Volkov-Husović, Tatjana and Jančić-Heinemann, Radmila",
year = "2021",
abstract = "Morphology and development of surface damage of alumina-based materials, resulting from cavitation erosion is studied in this paper. Two series of samples were prepared: samples without fibers and those with the addition of 2 wt % of ceramic fibers. The form of surface damage is considered to be the information carrier for the analysis of the resistance of materials to cavitation and the quality of this information is determined. The surface of the samples was monitored in defined time intervals in order to prepare the digitized image suitable for further analysis using image analysis software. The principal component analysis was applied to examine the appearance of certain morphological characteristics depending on the behavior of the material during cavitation erosion. It was concluded that the addition of ceramic fibers gained in importance after a long time of cavitation erosion, while during a starting period of time the difference in the morphology of the damage is not very observable. © 2021 Elsevier B.V.",
journal = "Wear",
title = "Advanced damage resistance monitoring procedure on the composite materials’ surface-exposed to cavitation testing",
volume = "474-475",
pages = "203877",
doi = "10.1016/j.wear.2021.203877"
}

Vuksanović, M. M., Gajić-Kvaščev, M., Volkov-Husović, T.,& Jančić-Heinemann, R.. (2021). Advanced damage resistance monitoring procedure on the composite materials’ surface-exposed to cavitation testing. in Wear, 474-475, 203877.
https://doi.org/10.1016/j.wear.2021.203877

Vuksanović MM, Gajić-Kvaščev M, Volkov-Husović T, Jančić-Heinemann R. Advanced damage resistance monitoring procedure on the composite materials’ surface-exposed to cavitation testing. in Wear. 2021;474-475:203877.
doi:10.1016/j.wear.2021.203877 .

Vuksanović, Marija M., Gajić-Kvaščev, Maja, Volkov-Husović, Tatjana, Jančić-Heinemann, Radmila, "Advanced damage resistance monitoring procedure on the composite materials’ surface-exposed to cavitation testing" in Wear, 474-475 (2021):203877,
https://doi.org/10.1016/j.wear.2021.203877 . .

Volkov Husović, T., Vuksanović, M. M., Gajić Kvaščev, M., Tomić, N., Jančić-Heinemann, R., Andrić, V., Martinović, S.,& Vlahović, M.. (2020). Nova metoda za sintezu keramičkih materijala i nedestruktivnu karakterizaciju površinskih oštećenja usled izlaganja kavitaciji. in Univerzitet u Beogradu : Tehnološko-metalurški fakultet.
https://hdl.handle.net/21.15107/rcub_vinar_13001

Volkov Husović T, Vuksanović MM, Gajić Kvaščev M, Tomić N, Jančić-Heinemann R, Andrić V, Martinović S, Vlahović M. Nova metoda za sintezu keramičkih materijala i nedestruktivnu karakterizaciju površinskih oštećenja usled izlaganja kavitaciji. in Univerzitet u Beogradu : Tehnološko-metalurški fakultet. 2020;.
https://hdl.handle.net/21.15107/rcub_vinar_13001 .

Volkov Husović, Tatjana, Vuksanović, Marija M., Gajić Kvaščev, Maja, Tomić, Nataša, Jančić-Heinemann, Radmila, Andrić, Velibor, Martinović, Sanja, Vlahović, Milica, "Nova metoda za sintezu keramičkih materijala i nedestruktivnu karakterizaciju površinskih oštećenja usled izlaganja kavitaciji" in Univerzitet u Beogradu : Tehnološko-metalurški fakultet (2020),
https://hdl.handle.net/21.15107/rcub_vinar_13001 .

TY  - JOUR
AU  - Kalifa, Mustafa
AU  - Tomić, Nataša Z.
AU  - Vuksanović, Marija M.
AU  - Stevanović, Sanja
AU  - Đokić, Veljko
AU  - Volkov-Husović, Tatjana
AU  - Pavlović, Vladimir B.
AU  - Jančić-Heinemann, Radmila
AU  - Marinković, Aleksandar D.
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9001
AB  - Cavitation erosion of hybrid acrylate composite films with polyhedraloligosilsesquioxanes (POSS) was investigated in this study. The hybrid films aremade with 1, 3 and 5 wt% of POSS reagents containing: (a) hydroxyl (POSS-M),(b) both hydroxyl and allyl (POSS-M-A) and (c) methacryloyl groups (POSS-MCl).Addition of 5 wt% POSS-M-A caused the highest microhardness increase for49.8%, in comparison to the pure matrix material. Cavitation resistance of hybridfilms, estimated as the time-dependent mass loss, was improved by POSS addition.POSS-M-A addition (5 wt%) contributed to 94% lower mass loss comparingto pure Bis-GMA/TEGDMA film. Scanning electron (SEM) and atomic forcemicroscopy (AFM) showed the lowest surface roughness obtained for compositewith POSS-M-A. The improved hardness and wear resistance of the compositefilms indicated that POSS-M-A filler enhanced interfacial adhesion and reinforcingof the Bis-GMA/TEGDMA matrix.
T2  - Polymer Composites
T1  - The effect of polyhedral oligosilsesquioxanes (POSS) on cavitation resistance of hybrid acrylate films
SP  - 3403
EP  - 3410
DO  - 10.1002/pc.25629
ER  - 

@article{
author = "Kalifa, Mustafa and Tomić, Nataša Z. and Vuksanović, Marija M. and Stevanović, Sanja and Đokić, Veljko and Volkov-Husović, Tatjana and Pavlović, Vladimir B. and Jančić-Heinemann, Radmila and Marinković, Aleksandar D.",
year = "2020",
abstract = "Cavitation erosion of hybrid acrylate composite films with polyhedraloligosilsesquioxanes (POSS) was investigated in this study. The hybrid films aremade with 1, 3 and 5 wt% of POSS reagents containing: (a) hydroxyl (POSS-M),(b) both hydroxyl and allyl (POSS-M-A) and (c) methacryloyl groups (POSS-MCl).Addition of 5 wt% POSS-M-A caused the highest microhardness increase for49.8%, in comparison to the pure matrix material. Cavitation resistance of hybridfilms, estimated as the time-dependent mass loss, was improved by POSS addition.POSS-M-A addition (5 wt%) contributed to 94% lower mass loss comparingto pure Bis-GMA/TEGDMA film. Scanning electron (SEM) and atomic forcemicroscopy (AFM) showed the lowest surface roughness obtained for compositewith POSS-M-A. The improved hardness and wear resistance of the compositefilms indicated that POSS-M-A filler enhanced interfacial adhesion and reinforcingof the Bis-GMA/TEGDMA matrix.",
journal = "Polymer Composites",
title = "The effect of polyhedral oligosilsesquioxanes (POSS) on cavitation resistance of hybrid acrylate films",
pages = "3403-3410",
doi = "10.1002/pc.25629"
}

Kalifa, M., Tomić, N. Z., Vuksanović, M. M., Stevanović, S., Đokić, V., Volkov-Husović, T., Pavlović, V. B., Jančić-Heinemann, R.,& Marinković, A. D.. (2020). The effect of polyhedral oligosilsesquioxanes (POSS) on cavitation resistance of hybrid acrylate films. in Polymer Composites, 3403-3410.
https://doi.org/10.1002/pc.25629

Kalifa M, Tomić NZ, Vuksanović MM, Stevanović S, Đokić V, Volkov-Husović T, Pavlović VB, Jančić-Heinemann R, Marinković AD. The effect of polyhedral oligosilsesquioxanes (POSS) on cavitation resistance of hybrid acrylate films. in Polymer Composites. 2020;:3403-3410.
doi:10.1002/pc.25629 .

Kalifa, Mustafa, Tomić, Nataša Z., Vuksanović, Marija M., Stevanović, Sanja, Đokić, Veljko, Volkov-Husović, Tatjana, Pavlović, Vladimir B., Jančić-Heinemann, Radmila, Marinković, Aleksandar D., "The effect of polyhedral oligosilsesquioxanes (POSS) on cavitation resistance of hybrid acrylate films" in Polymer Composites (2020):3403-3410,
https://doi.org/10.1002/pc.25629 . .

TY  - JOUR
AU  - Meseldžija, Slađana
AU  - Petrović, Jelena D.
AU  - Onjia, Antonije E.
AU  - Volkov-Husović, Tatjana
AU  - Nešić, Aleksandra
AU  - Vukelić, Nikola
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9734
AB  - This study is aimed to evaluate the possibility of lemon peel, as an agro-industrial waste, to remove Fe2+, Zn2+ and Mn2+ from single aqueous solutions and mining wastewater. For this purpose, the influence of various parameters: sorption time, initial pH solution, initial metal ion concentration and a dose of sorbent on the sorption process were studied in batch experiments. The experimental equilibrium data have been analysed utilizing linearized forms of Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms. The Langmuir isotherm provided the best theoretical correlation of the experimental equilibrium data for Fe2+, Zn2+ and Mn2+, with the maximum sorption capacities of 4.40, 5.03 and 4.52 mg g(-1), respectively. The percentage of targeted ions removal from single aqueous solutions was 92.9 % (Zn2+), 84.5 % (Fe2+) and 78.2 % (Mn2+). Regarding the sorption capability of lemon peel in mining wastewater, the maximum removal of Fe2+, Zn2+ and Mn2+ from mining wastewater was 49.62, 33.97 and 9.11 %, respectively. In addition, the potential reusability of the lemon peel as sorbent was investigated through desorption study in 0.1M of CH3COO4, HCl and HNO3 solution. The highest rate of desorption was achieved in 0.1 M HCl solution, reached a value of 55.19 % for Mn2+ and 37.24 % for Zn2+, while for Fe2+ the highest value of 25.82 % was achieved in 0.1M HNO3 solution.
PB  - Srpsko hemijsko društvo, Beograd
T2  - Journal of the Serbian Chemical Society
T1  - Removal of Fe2+, Zn2+ and Mn2+ from the mining wastewater by lemon peel waste
VL  - 85
IS  - 10
SP  - 1371
EP  - 1382
DO  - 10.2298/JSC200413030M
ER  - 

@article{
author = "Meseldžija, Slađana and Petrović, Jelena D. and Onjia, Antonije E. and Volkov-Husović, Tatjana and Nešić, Aleksandra and Vukelić, Nikola",
year = "2020",
abstract = "This study is aimed to evaluate the possibility of lemon peel, as an agro-industrial waste, to remove Fe2+, Zn2+ and Mn2+ from single aqueous solutions and mining wastewater. For this purpose, the influence of various parameters: sorption time, initial pH solution, initial metal ion concentration and a dose of sorbent on the sorption process were studied in batch experiments. The experimental equilibrium data have been analysed utilizing linearized forms of Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms. The Langmuir isotherm provided the best theoretical correlation of the experimental equilibrium data for Fe2+, Zn2+ and Mn2+, with the maximum sorption capacities of 4.40, 5.03 and 4.52 mg g(-1), respectively. The percentage of targeted ions removal from single aqueous solutions was 92.9 % (Zn2+), 84.5 % (Fe2+) and 78.2 % (Mn2+). Regarding the sorption capability of lemon peel in mining wastewater, the maximum removal of Fe2+, Zn2+ and Mn2+ from mining wastewater was 49.62, 33.97 and 9.11 %, respectively. In addition, the potential reusability of the lemon peel as sorbent was investigated through desorption study in 0.1M of CH3COO4, HCl and HNO3 solution. The highest rate of desorption was achieved in 0.1 M HCl solution, reached a value of 55.19 % for Mn2+ and 37.24 % for Zn2+, while for Fe2+ the highest value of 25.82 % was achieved in 0.1M HNO3 solution.",
publisher = "Srpsko hemijsko društvo, Beograd",
journal = "Journal of the Serbian Chemical Society",
title = "Removal of Fe2+, Zn2+ and Mn2+ from the mining wastewater by lemon peel waste",
volume = "85",
number = "10",
pages = "1371-1382",
doi = "10.2298/JSC200413030M"
}

Meseldžija, S., Petrović, J. D., Onjia, A. E., Volkov-Husović, T., Nešić, A.,& Vukelić, N.. (2020). Removal of Fe2+, Zn2+ and Mn2+ from the mining wastewater by lemon peel waste. in Journal of the Serbian Chemical Society
Srpsko hemijsko društvo, Beograd., 85(10), 1371-1382.
https://doi.org/10.2298/JSC200413030M

Meseldžija S, Petrović JD, Onjia AE, Volkov-Husović T, Nešić A, Vukelić N. Removal of Fe2+, Zn2+ and Mn2+ from the mining wastewater by lemon peel waste. in Journal of the Serbian Chemical Society. 2020;85(10):1371-1382.
doi:10.2298/JSC200413030M .

Meseldžija, Slađana, Petrović, Jelena D., Onjia, Antonije E., Volkov-Husović, Tatjana, Nešić, Aleksandra, Vukelić, Nikola, "Removal of Fe2+, Zn2+ and Mn2+ from the mining wastewater by lemon peel waste" in Journal of the Serbian Chemical Society, 85, no. 10 (2020):1371-1382,
https://doi.org/10.2298/JSC200413030M . .

TY  - JOUR
AU  - Abusahmin, Faisal
AU  - Algellai, Ahmed
AU  - Tomić, Nataša
AU  - Vuksanović, Marija M.
AU  - Majstorović, Jelena
AU  - Volkov-Husović, Tatjana
AU  - Simić, Vladimir
AU  - Jančić-Heinemann, Radmila
AU  - Toljić, Marinko
AU  - Kovačević, Jovan
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8979
AB  - Basalt as a filler in a polymer-based composite material fulfils the demand of being natural, environment-friendly material for the production of various composite materials. The material could be used as protective layer and the abrasion should be tested in order to evaluate the properties of the material. The cavitation test enables the evaluation of the possible service in conditions that simulate the extensive erosion. The presence of basalt in the matrix improves the resistance to cavitation. The possibility to further improve the material could be obtained using the reinforcement of the matrix itself by incorporation of submicron ceramic particles into the composite. The obtained hybrid composite material with the addition of reinforcement in the matrix further improves the cavitation resistance.
T2  - Science of Sintering
T1  - Basalt-polyester hybrid composite materials for demanding wear applications
VL  - 52
IS  - 1
SP  - 67
EP  - 76
DO  - 10.2298/SOS2001067A
ER  - 

@article{
author = "Abusahmin, Faisal and Algellai, Ahmed and Tomić, Nataša and Vuksanović, Marija M. and Majstorović, Jelena and Volkov-Husović, Tatjana and Simić, Vladimir and Jančić-Heinemann, Radmila and Toljić, Marinko and Kovačević, Jovan",
year = "2020",
abstract = "Basalt as a filler in a polymer-based composite material fulfils the demand of being natural, environment-friendly material for the production of various composite materials. The material could be used as protective layer and the abrasion should be tested in order to evaluate the properties of the material. The cavitation test enables the evaluation of the possible service in conditions that simulate the extensive erosion. The presence of basalt in the matrix improves the resistance to cavitation. The possibility to further improve the material could be obtained using the reinforcement of the matrix itself by incorporation of submicron ceramic particles into the composite. The obtained hybrid composite material with the addition of reinforcement in the matrix further improves the cavitation resistance.",
journal = "Science of Sintering",
title = "Basalt-polyester hybrid composite materials for demanding wear applications",
volume = "52",
number = "1",
pages = "67-76",
doi = "10.2298/SOS2001067A"
}

Abusahmin, F., Algellai, A., Tomić, N., Vuksanović, M. M., Majstorović, J., Volkov-Husović, T., Simić, V., Jančić-Heinemann, R., Toljić, M.,& Kovačević, J.. (2020). Basalt-polyester hybrid composite materials for demanding wear applications. in Science of Sintering, 52(1), 67-76.
https://doi.org/10.2298/SOS2001067A

Abusahmin F, Algellai A, Tomić N, Vuksanović MM, Majstorović J, Volkov-Husović T, Simić V, Jančić-Heinemann R, Toljić M, Kovačević J. Basalt-polyester hybrid composite materials for demanding wear applications. in Science of Sintering. 2020;52(1):67-76.
doi:10.2298/SOS2001067A .

Abusahmin, Faisal, Algellai, Ahmed, Tomić, Nataša, Vuksanović, Marija M., Majstorović, Jelena, Volkov-Husović, Tatjana, Simić, Vladimir, Jančić-Heinemann, Radmila, Toljić, Marinko, Kovačević, Jovan, "Basalt-polyester hybrid composite materials for demanding wear applications" in Science of Sintering, 52, no. 1 (2020):67-76,
https://doi.org/10.2298/SOS2001067A . .

TY  - JOUR
AU  - Simić, Marko
AU  - Alil, Ana
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Savić, Aleksandar R.
AU  - Volkov-Husović, Tatjana
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9708
AB  - High-temperature materials are used in a wide range of industries and applications such as gas turbine engines for aircrafts, power and nuclear power plants, different types of furnaces, including blast furnaces, some fuel cells, industrial gas turbines, different types of reactors, engines, electronic and lighting devices, and many others. Demands for high-temperature materials are becoming more and more challenging every year. To perform efficiently, effectively and at the same time to be economically viable, the materials used at high temperatures must have certain characteristics that are particularly expected for applying under such extreme conditions, for example, the strength and thermal resistance. In the present review, some important requirements that should be satisfied by high temperature materials will be discussed. Furthermore, the focus is put on refractory concretes, ceramics, intermetallic alloys, and composites as four different categories of these materials, which are also considered in respect to possibilities to overcome some of the current challenges.
T2  - Hemijska industrija
T2  - Hemijska industrija
T1  - High temperature materials: properties, demands and applications
VL  - 74
IS  - 4
SP  - 273
EP  - 284
DO  - 10.2298/HEMIND200421019S
ER  - 

@article{
author = "Simić, Marko and Alil, Ana and Martinović, Sanja and Vlahović, Milica and Savić, Aleksandar R. and Volkov-Husović, Tatjana",
year = "2020",
abstract = "High-temperature materials are used in a wide range of industries and applications such as gas turbine engines for aircrafts, power and nuclear power plants, different types of furnaces, including blast furnaces, some fuel cells, industrial gas turbines, different types of reactors, engines, electronic and lighting devices, and many others. Demands for high-temperature materials are becoming more and more challenging every year. To perform efficiently, effectively and at the same time to be economically viable, the materials used at high temperatures must have certain characteristics that are particularly expected for applying under such extreme conditions, for example, the strength and thermal resistance. In the present review, some important requirements that should be satisfied by high temperature materials will be discussed. Furthermore, the focus is put on refractory concretes, ceramics, intermetallic alloys, and composites as four different categories of these materials, which are also considered in respect to possibilities to overcome some of the current challenges.",
journal = "Hemijska industrija, Hemijska industrija",
title = "High temperature materials: properties, demands and applications",
volume = "74",
number = "4",
pages = "273-284",
doi = "10.2298/HEMIND200421019S"
}

Simić, M., Alil, A., Martinović, S., Vlahović, M., Savić, A. R.,& Volkov-Husović, T.. (2020). High temperature materials: properties, demands and applications. in Hemijska industrija, 74(4), 273-284.
https://doi.org/10.2298/HEMIND200421019S

Simić M, Alil A, Martinović S, Vlahović M, Savić AR, Volkov-Husović T. High temperature materials: properties, demands and applications. in Hemijska industrija. 2020;74(4):273-284.
doi:10.2298/HEMIND200421019S .

Simić, Marko, Alil, Ana, Martinović, Sanja, Vlahović, Milica, Savić, Aleksandar R., Volkov-Husović, Tatjana, "High temperature materials: properties, demands and applications" in Hemijska industrija, 74, no. 4 (2020):273-284,
https://doi.org/10.2298/HEMIND200421019S . .

TY  - JOUR
AU  - Zagorac, Jelena B.
AU  - Jovanović, Dušica
AU  - Volkov-Husović, Tatjana
AU  - Matović, Branko
AU  - Zagorac, Dejan
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8932
AB  - Ab initio data mining approach has been used in order to investigate B6O system and discover new possible modifications, besides experimentally known R-3m (α-B6O) structure and theoretically predicted Cmcm (β-B6O) structure. DFT calculations were performed by two different functionals, LDA and PBE. In this work, we focus on the structure, mechanical, and electronic properties of the experimentally known α-B6O structure and newly predicted modifications with the B6O stoichiometry. Moreover, mechanical properties including elastic constants, bulk, shear and elastic moduli, Poisson's ratio, Pugh's criterion, and hardness are given for the investigated modifications of B6O. In particular, we have investigated the influence of the high pressure on the electronic and mechanical properties. Results of our study provide more insight in the B6O superhard material and open new possibilities for various device applications.
T2  - Modelling and Simulation in Materials Science and Engineering
T1  - Structure prediction, high pressure effect and properties investigation of superhard B6O
VL  - 28
IS  - 3
DO  - 10.1088/1361-651X/ab6ec8
ER  - 

@article{
author = "Zagorac, Jelena B. and Jovanović, Dušica and Volkov-Husović, Tatjana and Matović, Branko and Zagorac, Dejan",
year = "2020",
abstract = "Ab initio data mining approach has been used in order to investigate B6O system and discover new possible modifications, besides experimentally known R-3m (α-B6O) structure and theoretically predicted Cmcm (β-B6O) structure. DFT calculations were performed by two different functionals, LDA and PBE. In this work, we focus on the structure, mechanical, and electronic properties of the experimentally known α-B6O structure and newly predicted modifications with the B6O stoichiometry. Moreover, mechanical properties including elastic constants, bulk, shear and elastic moduli, Poisson's ratio, Pugh's criterion, and hardness are given for the investigated modifications of B6O. In particular, we have investigated the influence of the high pressure on the electronic and mechanical properties. Results of our study provide more insight in the B6O superhard material and open new possibilities for various device applications.",
journal = "Modelling and Simulation in Materials Science and Engineering",
title = "Structure prediction, high pressure effect and properties investigation of superhard B6O",
volume = "28",
number = "3",
doi = "10.1088/1361-651X/ab6ec8"
}

Zagorac, J. B., Jovanović, D., Volkov-Husović, T., Matović, B.,& Zagorac, D.. (2020). Structure prediction, high pressure effect and properties investigation of superhard B6O. in Modelling and Simulation in Materials Science and Engineering, 28(3).
https://doi.org/10.1088/1361-651X/ab6ec8

Zagorac JB, Jovanović D, Volkov-Husović T, Matović B, Zagorac D. Structure prediction, high pressure effect and properties investigation of superhard B6O. in Modelling and Simulation in Materials Science and Engineering. 2020;28(3).
doi:10.1088/1361-651X/ab6ec8 .

Zagorac, Jelena B., Jovanović, Dušica, Volkov-Husović, Tatjana, Matović, Branko, Zagorac, Dejan, "Structure prediction, high pressure effect and properties investigation of superhard B6O" in Modelling and Simulation in Materials Science and Engineering, 28, no. 3 (2020),
https://doi.org/10.1088/1361-651X/ab6ec8 . .

TY  - JOUR
AU  - Meseldžija, Slađana
AU  - Petrović, Jelena M.
AU  - Onjia, Antonije E.
AU  - Volkov-Husović, Tatjana
AU  - Nešić, Aleksandra
AU  - Vukelić, Nikola
PY  - 2019
UR  - https://linkinghub.elsevier.com/retrieve/pii/S1226086X18311985
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8110
AB  - In this study, unmodified lemon peel, as agro-industrial waste, was used to investigate removal efficiency of copper ions from aqueous solutions and mining wastewater. The effects of solution pH, adsorption time, metal ion concentration and dose of adsorbent on sorption were studied in batch experiments. The maximum Langmuir adsorption capacity was evaluated to be 13.2 mg/g at optimum contact time of 15 min. The maximum removal of copper ions from mining-wastewater at natural pH (pH3) was 89%, indicating that lemon peel could be employed as an effective low-cost adsorbent for removal of copper ions from wastewater at acidic conditions. © 2019 The Korean Society of Industrial and Engineering Chemistry
T2  - Journal of Industrial and Engineering Chemistry
T1  - Utilization of agro-industrial waste for removal of copper ions from aqueous solutions and mining-wastewater
VL  - 75
SP  - 246
EP  - 252
DO  - 10.1016/j.jiec.2019.03.031
ER  - 

@article{
author = "Meseldžija, Slađana and Petrović, Jelena M. and Onjia, Antonije E. and Volkov-Husović, Tatjana and Nešić, Aleksandra and Vukelić, Nikola",
year = "2019",
abstract = "In this study, unmodified lemon peel, as agro-industrial waste, was used to investigate removal efficiency of copper ions from aqueous solutions and mining wastewater. The effects of solution pH, adsorption time, metal ion concentration and dose of adsorbent on sorption were studied in batch experiments. The maximum Langmuir adsorption capacity was evaluated to be 13.2 mg/g at optimum contact time of 15 min. The maximum removal of copper ions from mining-wastewater at natural pH (pH3) was 89%, indicating that lemon peel could be employed as an effective low-cost adsorbent for removal of copper ions from wastewater at acidic conditions. © 2019 The Korean Society of Industrial and Engineering Chemistry",
journal = "Journal of Industrial and Engineering Chemistry",
title = "Utilization of agro-industrial waste for removal of copper ions from aqueous solutions and mining-wastewater",
volume = "75",
pages = "246-252",
doi = "10.1016/j.jiec.2019.03.031"
}

Meseldžija, S., Petrović, J. M., Onjia, A. E., Volkov-Husović, T., Nešić, A.,& Vukelić, N.. (2019). Utilization of agro-industrial waste for removal of copper ions from aqueous solutions and mining-wastewater. in Journal of Industrial and Engineering Chemistry, 75, 246-252.
https://doi.org/10.1016/j.jiec.2019.03.031

Meseldžija S, Petrović JM, Onjia AE, Volkov-Husović T, Nešić A, Vukelić N. Utilization of agro-industrial waste for removal of copper ions from aqueous solutions and mining-wastewater. in Journal of Industrial and Engineering Chemistry. 2019;75:246-252.
doi:10.1016/j.jiec.2019.03.031 .

Meseldžija, Slađana, Petrović, Jelena M., Onjia, Antonije E., Volkov-Husović, Tatjana, Nešić, Aleksandra, Vukelić, Nikola, "Utilization of agro-industrial waste for removal of copper ions from aqueous solutions and mining-wastewater" in Journal of Industrial and Engineering Chemistry, 75 (2019):246-252,
https://doi.org/10.1016/j.jiec.2019.03.031 . .

Gajić-Kvaščev, M., Jančić Heinemann, R., Vuksanović, M. M., Tomić, N., Volkov Husović, T., Andrić, V.,& Brdarić, T.. (2018). Nova metoda karakterizacije površinskih termičkih oštećenja vatrostalnih keramičkih materijala primenom hemometrijskih i alata analize slike. .
https://hdl.handle.net/21.15107/rcub_vinar_13004

Gajić-Kvaščev M, Jančić Heinemann R, Vuksanović MM, Tomić N, Volkov Husović T, Andrić V, Brdarić T. Nova metoda karakterizacije površinskih termičkih oštećenja vatrostalnih keramičkih materijala primenom hemometrijskih i alata analize slike. 2018;.
https://hdl.handle.net/21.15107/rcub_vinar_13004 .

Gajić-Kvaščev, Maja, Jančić Heinemann, Radmila, Vuksanović, Marija M., Tomić, Nataša, Volkov Husović, Tatjana, Andrić, Velibor, Brdarić, Tanja, "Nova metoda karakterizacije površinskih termičkih oštećenja vatrostalnih keramičkih materijala primenom hemometrijskih i alata analize slike" (2018),
https://hdl.handle.net/21.15107/rcub_vinar_13004 .

TY  - JOUR
AU  - Vuksanović, Marija M.
AU  - Gajić-Kvaščev, Maja
AU  - Dojčinović, Marina
AU  - Volkov-Husović, Tatjana
AU  - Jančić-Heinemann, Radmila
PY  - 2018
UR  - https://linkinghub.elsevier.com/retrieve/pii/S1044580318313445
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7771
AB  - The aim of this study was to examine the influence of cavitation erosion on the morphology of defects formed on the surfaces of alumina-based materials. The alumina-based samples were exposed to cavitation erosion for 42 min. The damages that occurred were monitored at predefined time intervals by measuring the mass loss and observing the sample surfaces. Digital images of surfaces were processed using an image analysis software package to define morphological characteristics of the damages occurred. The calculated morphological parameters were subjected to analysis by pattern recognition techniques to correlate the appearance of particular morphological characteristics with the behavior of the material during cavitation erosion. The newly established method in describing cavitation erosion which uses pattern recognition approach for treatments of morphological parameters calculated for damages by image analysis tools gave the results efficient for material characterization as the traditional one. © 2018 Elsevier Inc.
T2  - Materials Characterization
T1  - New surface characterization tools for alumina based refractory material exposed to cavitation - Image analysis and pattern recognition approach
VL  - 144
SP  - 113
EP  - 119
DO  - 10.1016/j.matchar.2018.07.003
ER  - 

@article{
author = "Vuksanović, Marija M. and Gajić-Kvaščev, Maja and Dojčinović, Marina and Volkov-Husović, Tatjana and Jančić-Heinemann, Radmila",
year = "2018",
abstract = "The aim of this study was to examine the influence of cavitation erosion on the morphology of defects formed on the surfaces of alumina-based materials. The alumina-based samples were exposed to cavitation erosion for 42 min. The damages that occurred were monitored at predefined time intervals by measuring the mass loss and observing the sample surfaces. Digital images of surfaces were processed using an image analysis software package to define morphological characteristics of the damages occurred. The calculated morphological parameters were subjected to analysis by pattern recognition techniques to correlate the appearance of particular morphological characteristics with the behavior of the material during cavitation erosion. The newly established method in describing cavitation erosion which uses pattern recognition approach for treatments of morphological parameters calculated for damages by image analysis tools gave the results efficient for material characterization as the traditional one. © 2018 Elsevier Inc.",
journal = "Materials Characterization",
title = "New surface characterization tools for alumina based refractory material exposed to cavitation - Image analysis and pattern recognition approach",
volume = "144",
pages = "113-119",
doi = "10.1016/j.matchar.2018.07.003"
}

Vuksanović, M. M., Gajić-Kvaščev, M., Dojčinović, M., Volkov-Husović, T.,& Jančić-Heinemann, R.. (2018). New surface characterization tools for alumina based refractory material exposed to cavitation - Image analysis and pattern recognition approach. in Materials Characterization, 144, 113-119.
https://doi.org/10.1016/j.matchar.2018.07.003

Vuksanović MM, Gajić-Kvaščev M, Dojčinović M, Volkov-Husović T, Jančić-Heinemann R. New surface characterization tools for alumina based refractory material exposed to cavitation - Image analysis and pattern recognition approach. in Materials Characterization. 2018;144:113-119.
doi:10.1016/j.matchar.2018.07.003 .

Vuksanović, Marija M., Gajić-Kvaščev, Maja, Dojčinović, Marina, Volkov-Husović, Tatjana, Jančić-Heinemann, Radmila, "New surface characterization tools for alumina based refractory material exposed to cavitation - Image analysis and pattern recognition approach" in Materials Characterization, 144 (2018):113-119,
https://doi.org/10.1016/j.matchar.2018.07.003 . .

TY  - JOUR
AU  - Maksimović, Vesna
AU  - Devečerski, Aleksandar
AU  - Došen, Anja M.
AU  - Bobić, Ilija
AU  - Erić, Milić D.
AU  - Volkov-Husović, Tatjana
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1391
AB  - In the present study, an aluminum alloy A356 composite with addition of 5 wt% fly ash was synthesized and subjected to the cavitation erosion resistance test in order to find out if this material can be used in conditions where the cavitation erosion resistance is expected. Obtained results were compared with that of as-cast aluminum A356 alloy, confirming that composite possessed better cavitation erosion resistance than original alloy and that fly ash can be used as an effective reinforcement in metal matrix composites production. Scanning electron microscopy and optical microscopy was used for microstructural analysis. Phase identification of fly ash was carried out using X-ray diffraction analysis. Several methods for monitoring the cavitation erosion resistance of A356 alloy and corresponding composite were applied, such as: mass loss (Delta m), volume loss (Delta V), level of surface degradatiom (P/Po) and pit depth.
T2  - Transactions of the Indian Institute of Metals
T1  - Comparative Study on Cavitation Erosion Resistance of A356 Alloy and A356FA5 Composite
VL  - 70
IS  - 1
SP  - 97
EP  - 105
DO  - 10.1007/s12666-016-0864-1
ER  - 

@article{
author = "Maksimović, Vesna and Devečerski, Aleksandar and Došen, Anja M. and Bobić, Ilija and Erić, Milić D. and Volkov-Husović, Tatjana",
year = "2017",
abstract = "In the present study, an aluminum alloy A356 composite with addition of 5 wt% fly ash was synthesized and subjected to the cavitation erosion resistance test in order to find out if this material can be used in conditions where the cavitation erosion resistance is expected. Obtained results were compared with that of as-cast aluminum A356 alloy, confirming that composite possessed better cavitation erosion resistance than original alloy and that fly ash can be used as an effective reinforcement in metal matrix composites production. Scanning electron microscopy and optical microscopy was used for microstructural analysis. Phase identification of fly ash was carried out using X-ray diffraction analysis. Several methods for monitoring the cavitation erosion resistance of A356 alloy and corresponding composite were applied, such as: mass loss (Delta m), volume loss (Delta V), level of surface degradatiom (P/Po) and pit depth.",
journal = "Transactions of the Indian Institute of Metals",
title = "Comparative Study on Cavitation Erosion Resistance of A356 Alloy and A356FA5 Composite",
volume = "70",
number = "1",
pages = "97-105",
doi = "10.1007/s12666-016-0864-1"
}

Maksimović, V., Devečerski, A., Došen, A. M., Bobić, I., Erić, M. D.,& Volkov-Husović, T.. (2017). Comparative Study on Cavitation Erosion Resistance of A356 Alloy and A356FA5 Composite. in Transactions of the Indian Institute of Metals, 70(1), 97-105.
https://doi.org/10.1007/s12666-016-0864-1

Maksimović V, Devečerski A, Došen AM, Bobić I, Erić MD, Volkov-Husović T. Comparative Study on Cavitation Erosion Resistance of A356 Alloy and A356FA5 Composite. in Transactions of the Indian Institute of Metals. 2017;70(1):97-105.
doi:10.1007/s12666-016-0864-1 .

Maksimović, Vesna, Devečerski, Aleksandar, Došen, Anja M., Bobić, Ilija, Erić, Milić D., Volkov-Husović, Tatjana, "Comparative Study on Cavitation Erosion Resistance of A356 Alloy and A356FA5 Composite" in Transactions of the Indian Institute of Metals, 70, no. 1 (2017):97-105,
https://doi.org/10.1007/s12666-016-0864-1 . .

TY  - JOUR
AU  - Ružić, Jovana
AU  - Stašić, Jelena
AU  - Božić, Dušan
AU  - Dojčinović, Marina
AU  - Volkov-Husović, Tatjana
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1942
AB  - Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations in the microstructure of treated samples obtained during cavitation test were analyzed by scanning electron microscopy (SEM). Cavitation erosion resistance was investigated with the standard test method for cavitation erosion using vibratory apparatus. Changes in mechanical alloying duration show a strong influence on cavitation erosion resistance of Cu-ZrB2 composites regardless the number of reinforcements. Laser-sintered samples show better cavitation erosion resistance than hot-pressed samples.
T2  - Metallurgical and Materials Engineering
T1  - Influence of the Fabrication Process of Copper Matrix Composites on Cavitation Erosion Resistance
VL  - 23
IS  - 4
SP  - 291
EP  - 301
DO  - 10.30544/244291
ER  - 

@article{
author = "Ružić, Jovana and Stašić, Jelena and Božić, Dušan and Dojčinović, Marina and Volkov-Husović, Tatjana",
year = "2017",
abstract = "Copper matrix composites reinforced with ZrB2 particles were produced in two ways: by hot pressing (HP) and laser-sintering process. Powder mixture Cu-Zr-B was mechanically alloyed before densification processes. Variations in the microstructure of treated samples obtained during cavitation test were analyzed by scanning electron microscopy (SEM). Cavitation erosion resistance was investigated with the standard test method for cavitation erosion using vibratory apparatus. Changes in mechanical alloying duration show a strong influence on cavitation erosion resistance of Cu-ZrB2 composites regardless the number of reinforcements. Laser-sintered samples show better cavitation erosion resistance than hot-pressed samples.",
journal = "Metallurgical and Materials Engineering",
title = "Influence of the Fabrication Process of Copper Matrix Composites on Cavitation Erosion Resistance",
volume = "23",
number = "4",
pages = "291-301",
doi = "10.30544/244291"
}

Ružić, J., Stašić, J., Božić, D., Dojčinović, M.,& Volkov-Husović, T.. (2017). Influence of the Fabrication Process of Copper Matrix Composites on Cavitation Erosion Resistance. in Metallurgical and Materials Engineering, 23(4), 291-301.
https://doi.org/10.30544/244291

Ružić J, Stašić J, Božić D, Dojčinović M, Volkov-Husović T. Influence of the Fabrication Process of Copper Matrix Composites on Cavitation Erosion Resistance. in Metallurgical and Materials Engineering. 2017;23(4):291-301.
doi:10.30544/244291 .

Ružić, Jovana, Stašić, Jelena, Božić, Dušan, Dojčinović, Marina, Volkov-Husović, Tatjana, "Influence of the Fabrication Process of Copper Matrix Composites on Cavitation Erosion Resistance" in Metallurgical and Materials Engineering, 23, no. 4 (2017):291-301,
https://doi.org/10.30544/244291 . .

TY  - JOUR
AU  - Cocic, Mira
AU  - Matović, Branko
AU  - Pošarac, Milica B.
AU  - Volkov-Husović, Tatjana
AU  - Majstorović, Jelena
AU  - Tasic, Visa
AU  - Devic, Snezana
AU  - Vusovic, Nenad
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1643
AB  - In this study, the behavior of glass-ceramics synthesized from a glass frit of FFW (Final Flotation Waste) originated from the RTB Bor Company was investigated. Thermal shock resistance was monitored in order to assess the possibility of application of such waste material. Thermal shock of the samples was conducted using water quench test. Image analysis and ultrasonic measurements were used as nondestructive methods for quantification of thermal shock damage at the surface and in the bulk of the specimens. Phase composition of samples was determined by X-ray powder diffraction (XRPD). The degradation level of samples was about 43 % after 20 cycles of water quench tests. The results pointed out that glass-ceramic material exhibited good thermal shock resistance.
T2  - Science of Sintering
T1  - Thermal Shock Properties of Glass-ceramics Synthesized From a Glass Frit
VL  - 49
IS  - 2
SP  - 139
EP  - 147
DO  - 10.2298/SOS1702139C
ER  - 

@article{
author = "Cocic, Mira and Matović, Branko and Pošarac, Milica B. and Volkov-Husović, Tatjana and Majstorović, Jelena and Tasic, Visa and Devic, Snezana and Vusovic, Nenad",
year = "2017",
abstract = "In this study, the behavior of glass-ceramics synthesized from a glass frit of FFW (Final Flotation Waste) originated from the RTB Bor Company was investigated. Thermal shock resistance was monitored in order to assess the possibility of application of such waste material. Thermal shock of the samples was conducted using water quench test. Image analysis and ultrasonic measurements were used as nondestructive methods for quantification of thermal shock damage at the surface and in the bulk of the specimens. Phase composition of samples was determined by X-ray powder diffraction (XRPD). The degradation level of samples was about 43 % after 20 cycles of water quench tests. The results pointed out that glass-ceramic material exhibited good thermal shock resistance.",
journal = "Science of Sintering",
title = "Thermal Shock Properties of Glass-ceramics Synthesized From a Glass Frit",
volume = "49",
number = "2",
pages = "139-147",
doi = "10.2298/SOS1702139C"
}

Cocic, M., Matović, B., Pošarac, M. B., Volkov-Husović, T., Majstorović, J., Tasic, V., Devic, S.,& Vusovic, N.. (2017). Thermal Shock Properties of Glass-ceramics Synthesized From a Glass Frit. in Science of Sintering, 49(2), 139-147.
https://doi.org/10.2298/SOS1702139C

Cocic M, Matović B, Pošarac MB, Volkov-Husović T, Majstorović J, Tasic V, Devic S, Vusovic N. Thermal Shock Properties of Glass-ceramics Synthesized From a Glass Frit. in Science of Sintering. 2017;49(2):139-147.
doi:10.2298/SOS1702139C .

Cocic, Mira, Matović, Branko, Pošarac, Milica B., Volkov-Husović, Tatjana, Majstorović, Jelena, Tasic, Visa, Devic, Snezana, Vusovic, Nenad, "Thermal Shock Properties of Glass-ceramics Synthesized From a Glass Frit" in Science of Sintering, 49, no. 2 (2017):139-147,
https://doi.org/10.2298/SOS1702139C . .

TY  - JOUR
AU  - Luković, Jelena M.
AU  - Zagorac, Dejan
AU  - Schoen, J. Christian
AU  - Zagorac, Jelena B.
AU  - Jordanov, Dragana
AU  - Volkov-Husović, Tatjana
AU  - Matović, Branko
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1868
AB  - Transition metal silicides have attracted great attention due to their potential applications in microelectronics, ceramics, and the aerospace industry. In this study, experimental and theoretical investigations of tungsten based silicides were performed. Tungsten disilicide (WSi2) was synthesized by simple thermal treatment at 1350 degrees C for 4 h in an argon atmosphere. These optimal synthesis conditions were obtained by variation of temperatures and times of heating, and the structure of the final synthesized compound was determined by XRPD analysis. In addition, new modifications for WSi2 were proposed and investigated using first-principles calculations within density-functional theory (DFT). Both LDA and PBE calculations show excellent agreement with experimental observations and previous calculations for the existing modifications, where available.
T2  - Zeitschrift fur Anorganische und Allgemeine Chemie
T1  - Tungsten Disilicide (WSi2): Synthesis, Characterization, and Prediction of New Crystal Structures
VL  - 643
IS  - 23
SP  - 2088
EP  - 2094
DO  - 10.1002/zaac.201700329
ER  - 

@article{
author = "Luković, Jelena M. and Zagorac, Dejan and Schoen, J. Christian and Zagorac, Jelena B. and Jordanov, Dragana and Volkov-Husović, Tatjana and Matović, Branko",
year = "2017",
abstract = "Transition metal silicides have attracted great attention due to their potential applications in microelectronics, ceramics, and the aerospace industry. In this study, experimental and theoretical investigations of tungsten based silicides were performed. Tungsten disilicide (WSi2) was synthesized by simple thermal treatment at 1350 degrees C for 4 h in an argon atmosphere. These optimal synthesis conditions were obtained by variation of temperatures and times of heating, and the structure of the final synthesized compound was determined by XRPD analysis. In addition, new modifications for WSi2 were proposed and investigated using first-principles calculations within density-functional theory (DFT). Both LDA and PBE calculations show excellent agreement with experimental observations and previous calculations for the existing modifications, where available.",
journal = "Zeitschrift fur Anorganische und Allgemeine Chemie",
title = "Tungsten Disilicide (WSi2): Synthesis, Characterization, and Prediction of New Crystal Structures",
volume = "643",
number = "23",
pages = "2088-2094",
doi = "10.1002/zaac.201700329"
}

Luković, J. M., Zagorac, D., Schoen, J. C., Zagorac, J. B., Jordanov, D., Volkov-Husović, T.,& Matović, B.. (2017). Tungsten Disilicide (WSi2): Synthesis, Characterization, and Prediction of New Crystal Structures. in Zeitschrift fur Anorganische und Allgemeine Chemie, 643(23), 2088-2094.
https://doi.org/10.1002/zaac.201700329

Luković JM, Zagorac D, Schoen JC, Zagorac JB, Jordanov D, Volkov-Husović T, Matović B. Tungsten Disilicide (WSi2): Synthesis, Characterization, and Prediction of New Crystal Structures. in Zeitschrift fur Anorganische und Allgemeine Chemie. 2017;643(23):2088-2094.
doi:10.1002/zaac.201700329 .

Luković, Jelena M., Zagorac, Dejan, Schoen, J. Christian, Zagorac, Jelena B., Jordanov, Dragana, Volkov-Husović, Tatjana, Matović, Branko, "Tungsten Disilicide (WSi2): Synthesis, Characterization, and Prediction of New Crystal Structures" in Zeitschrift fur Anorganische und Allgemeine Chemie, 643, no. 23 (2017):2088-2094,
https://doi.org/10.1002/zaac.201700329 . .

TY  - JOUR
AU  - Nešić, Aleksandra
AU  - Kokunešoski, Maja
AU  - Meseldžija, Slađana
AU  - Volkov-Husović, Tatjana
AU  - Veličković, Sava J.
AU  - Onjia, Antonije E.
PY  - 2016
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1302
AB  - In this work, the reliability of image analysis for the numerical evaluation of Basic Red 46 (BR 46) dye adsorption process was studied. The image analysis was carried out on dye adsorbed onto SBA-15 mesoporous silica, by use of Image-Pro Plus software. Pixel-specific calibration curves were derived and used to obtain dye concentration from the three different primary color channels (red, green, and blue) recorded at each pixel. In order to establish credibility of this method for quantification of adsorption processes, these data were compared with dye adsorption parameters obtained by UV-vis analysis. Among the three different primary color channels, the best results were obtained when the blue color channel was applied. In this case, the average relative error was 0.86%. The obtained results showed that a dye adsorbed on SBA-15 can be determined with the use of Image-Pro Plus with the same sensitivity as with the use of spectrophotometric analysis for the determination of changes in dye concentration during the adsorption process.
T2  - CLEAN - Soil Air Water
T1  - Evaluation of Dye Adsorption Onto SBA-15 Using Image Analysis
VL  - 44
IS  - 10
SP  - 1323
EP  - 1328
DO  - 10.1002/clen.201500565
ER  - 

@article{
author = "Nešić, Aleksandra and Kokunešoski, Maja and Meseldžija, Slađana and Volkov-Husović, Tatjana and Veličković, Sava J. and Onjia, Antonije E.",
year = "2016",
abstract = "In this work, the reliability of image analysis for the numerical evaluation of Basic Red 46 (BR 46) dye adsorption process was studied. The image analysis was carried out on dye adsorbed onto SBA-15 mesoporous silica, by use of Image-Pro Plus software. Pixel-specific calibration curves were derived and used to obtain dye concentration from the three different primary color channels (red, green, and blue) recorded at each pixel. In order to establish credibility of this method for quantification of adsorption processes, these data were compared with dye adsorption parameters obtained by UV-vis analysis. Among the three different primary color channels, the best results were obtained when the blue color channel was applied. In this case, the average relative error was 0.86%. The obtained results showed that a dye adsorbed on SBA-15 can be determined with the use of Image-Pro Plus with the same sensitivity as with the use of spectrophotometric analysis for the determination of changes in dye concentration during the adsorption process.",
journal = "CLEAN - Soil Air Water",
title = "Evaluation of Dye Adsorption Onto SBA-15 Using Image Analysis",
volume = "44",
number = "10",
pages = "1323-1328",
doi = "10.1002/clen.201500565"
}

Nešić, A., Kokunešoski, M., Meseldžija, S., Volkov-Husović, T., Veličković, S. J.,& Onjia, A. E.. (2016). Evaluation of Dye Adsorption Onto SBA-15 Using Image Analysis. in CLEAN - Soil Air Water, 44(10), 1323-1328.
https://doi.org/10.1002/clen.201500565

Nešić A, Kokunešoski M, Meseldžija S, Volkov-Husović T, Veličković SJ, Onjia AE. Evaluation of Dye Adsorption Onto SBA-15 Using Image Analysis. in CLEAN - Soil Air Water. 2016;44(10):1323-1328.
doi:10.1002/clen.201500565 .

Nešić, Aleksandra, Kokunešoski, Maja, Meseldžija, Slađana, Volkov-Husović, Tatjana, Veličković, Sava J., Onjia, Antonije E., "Evaluation of Dye Adsorption Onto SBA-15 Using Image Analysis" in CLEAN - Soil Air Water, 44, no. 10 (2016):1323-1328,
https://doi.org/10.1002/clen.201500565 . .

TY  - JOUR
AU  - Matović, Branko
AU  - Bučevac, Dušan
AU  - Urbanović, Vladimir
AU  - Stanković, Nadežda
AU  - Daneu, Nina
AU  - Volkov-Husović, Tatjana
AU  - Babić, Biljana M.
PY  - 2016
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1134
AB  - Additive-free beta-SiC nanopowders were densified by using high-pressure anvil-type with hollows apparatus at the pressure of 4 GPa in the range of 1500-1900 degrees C. The starting powder with average particle size of 10 nm was synthesized by a sol-gel process. Crystallite size and lattice parameters of the samples have been studied at room temperature by X-ray diffraction (XRD) and transmission electron microscopy (TEM). It was found that the size of the crystallites gradually increases from 16 to 51 nm with increasing sintering temperature (1500 to 1900 degrees C). Fully densified sample ( GT 99%) was obtained at a sintering temperature of 1900 degrees C for 60 s. This sample exhibits nano-hardness and Youngs modulus of elasticity of 35 GPa and 450 GPa, respectively. Modified vibratory cavitation test method was used for laboratory testing of the cavitation resistance. A very low erosion level with mass loss 0.1% after 10 h was exhibited during the cavitation test. (C) 2015 Elsevier Ltd. All rights reserved.
T2  - Journal of the European Ceramic Society
T1  - Monolithic nanocrystalline SiC ceramics
VL  - 36
IS  - 12
SP  - 3005
EP  - 3010
DO  - 10.1016/j.jeurceramsoc.2015.10.031
ER  - 

@article{
author = "Matović, Branko and Bučevac, Dušan and Urbanović, Vladimir and Stanković, Nadežda and Daneu, Nina and Volkov-Husović, Tatjana and Babić, Biljana M.",
year = "2016",
abstract = "Additive-free beta-SiC nanopowders were densified by using high-pressure anvil-type with hollows apparatus at the pressure of 4 GPa in the range of 1500-1900 degrees C. The starting powder with average particle size of 10 nm was synthesized by a sol-gel process. Crystallite size and lattice parameters of the samples have been studied at room temperature by X-ray diffraction (XRD) and transmission electron microscopy (TEM). It was found that the size of the crystallites gradually increases from 16 to 51 nm with increasing sintering temperature (1500 to 1900 degrees C). Fully densified sample ( GT 99%) was obtained at a sintering temperature of 1900 degrees C for 60 s. This sample exhibits nano-hardness and Youngs modulus of elasticity of 35 GPa and 450 GPa, respectively. Modified vibratory cavitation test method was used for laboratory testing of the cavitation resistance. A very low erosion level with mass loss 0.1% after 10 h was exhibited during the cavitation test. (C) 2015 Elsevier Ltd. All rights reserved.",
journal = "Journal of the European Ceramic Society",
title = "Monolithic nanocrystalline SiC ceramics",
volume = "36",
number = "12",
pages = "3005-3010",
doi = "10.1016/j.jeurceramsoc.2015.10.031"
}

Matović, B., Bučevac, D., Urbanović, V., Stanković, N., Daneu, N., Volkov-Husović, T.,& Babić, B. M.. (2016). Monolithic nanocrystalline SiC ceramics. in Journal of the European Ceramic Society, 36(12), 3005-3010.
https://doi.org/10.1016/j.jeurceramsoc.2015.10.031

Matović B, Bučevac D, Urbanović V, Stanković N, Daneu N, Volkov-Husović T, Babić BM. Monolithic nanocrystalline SiC ceramics. in Journal of the European Ceramic Society. 2016;36(12):3005-3010.
doi:10.1016/j.jeurceramsoc.2015.10.031 .

Matović, Branko, Bučevac, Dušan, Urbanović, Vladimir, Stanković, Nadežda, Daneu, Nina, Volkov-Husović, Tatjana, Babić, Biljana M., "Monolithic nanocrystalline SiC ceramics" in Journal of the European Ceramic Society, 36, no. 12 (2016):3005-3010,
https://doi.org/10.1016/j.jeurceramsoc.2015.10.031 . .

TY  - JOUR
AU  - Matović, Branko
AU  - Živić, Fatima
AU  - Mitrovic, Slobodan
AU  - Pršić, Dragan H.
AU  - Maksimović, Vesna
AU  - Volkov-Husović, Tatjana
AU  - Kumar, Ravi
AU  - Daneu, Nina
PY  - 2016
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/864
AB  - Cubic SiC nano-powder particles were synthesized by a sal-gel process with an average grains size of 9.5 nm which were subsequently densified by using a high-pressure anvil-type with hollows apparatus at a pressure of 4 GPa in order to obtain nanostructured bulk ceramic compacts. The density obtained was GT 98% at a sintering temperature of 1500 degrees C with a holding time of only 60s. The calculation of the average crystallite size (D) was performed on the basis of the full width at half maximum intensity (FWHM) of the XRD peaks. Williamson-Hall plots were used to separate the effect of the size and strain in the nanostructured SiC compacts. Sintered nanostructured SiC ceramic exhibits hardness and elastic modulus of 32-420 GPa respectively. Wear properties were investigated and the average value of dynamic friction coefficient obtained was 0.16. (C) 2015 Elsevier B.V. All rights reserved.
PB  - Elsevier
T2  - Materials Letters
T1  - Ultra-high pressure densification and properties of nanostructured SiC
VL  - 164
SP  - 68
EP  - 71
DO  - 10.1016/j.matlet.2015.09.043
ER  - 

@article{
author = "Matović, Branko and Živić, Fatima and Mitrovic, Slobodan and Pršić, Dragan H. and Maksimović, Vesna and Volkov-Husović, Tatjana and Kumar, Ravi and Daneu, Nina",
year = "2016",
abstract = "Cubic SiC nano-powder particles were synthesized by a sal-gel process with an average grains size of 9.5 nm which were subsequently densified by using a high-pressure anvil-type with hollows apparatus at a pressure of 4 GPa in order to obtain nanostructured bulk ceramic compacts. The density obtained was GT 98% at a sintering temperature of 1500 degrees C with a holding time of only 60s. The calculation of the average crystallite size (D) was performed on the basis of the full width at half maximum intensity (FWHM) of the XRD peaks. Williamson-Hall plots were used to separate the effect of the size and strain in the nanostructured SiC compacts. Sintered nanostructured SiC ceramic exhibits hardness and elastic modulus of 32-420 GPa respectively. Wear properties were investigated and the average value of dynamic friction coefficient obtained was 0.16. (C) 2015 Elsevier B.V. All rights reserved.",
publisher = "Elsevier",
journal = "Materials Letters",
title = "Ultra-high pressure densification and properties of nanostructured SiC",
volume = "164",
pages = "68-71",
doi = "10.1016/j.matlet.2015.09.043"
}

Matović, B., Živić, F., Mitrovic, S., Pršić, D. H., Maksimović, V., Volkov-Husović, T., Kumar, R.,& Daneu, N.. (2016). Ultra-high pressure densification and properties of nanostructured SiC. in Materials Letters
Elsevier., 164, 68-71.
https://doi.org/10.1016/j.matlet.2015.09.043

Matović B, Živić F, Mitrovic S, Pršić DH, Maksimović V, Volkov-Husović T, Kumar R, Daneu N. Ultra-high pressure densification and properties of nanostructured SiC. in Materials Letters. 2016;164:68-71.
doi:10.1016/j.matlet.2015.09.043 .

Matović, Branko, Živić, Fatima, Mitrovic, Slobodan, Pršić, Dragan H., Maksimović, Vesna, Volkov-Husović, Tatjana, Kumar, Ravi, Daneu, Nina, "Ultra-high pressure densification and properties of nanostructured SiC" in Materials Letters, 164 (2016):68-71,
https://doi.org/10.1016/j.matlet.2015.09.043 . .

TY  - JOUR
AU  - Nešić, Aleksandra
AU  - Kokunešoski, Maja
AU  - Volkov-Husović, Tatjana
AU  - Veličković, Sava J.
PY  - 2016
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/954
AB  - In this work, a new method for the quantification of methyl violet cationic dye sorption onto SBA-15 mesoporous silica was developed. This method related the intensity of coloration of SBA-15 samples (after reached equilibrium sorption) within dye concentration in aqueous solution using Image-Pro Plus software. The sorption process of methyl violet dye onto SBA-15 was analyzed varying different initial parameters (dye concentration, mass of sorbent, pH of dye solution, and contact sorption time). SBA-15 proved as efficient sorbent for removal of methyl violet dye in contact time of 5 min, with maximum percentage of dye removal 99% at pH 8. The results obtained from Image-Pro Plus showed to be in good agreement with the sorption parameters obtained by UV/Vis spectroscopy, which has been the most commonly used instrument for quantification of dye sorption. The image analysis method proved well prediction of dye concentrations with maximum relative error of 1.83 %. The advantages of this method are low cost and reliable quantitative evaluation with minimum of time.
PB  - Springer
T2  - Environmental Monitoring and Assessment
T1  - New method for quantification of dye sorption using SBA mesoporous silica as a target sorbent
VL  - 188
IS  - 3
DO  - 10.1007/s10661-016-5155-0
ER  - 

@article{
author = "Nešić, Aleksandra and Kokunešoski, Maja and Volkov-Husović, Tatjana and Veličković, Sava J.",
year = "2016",
abstract = "In this work, a new method for the quantification of methyl violet cationic dye sorption onto SBA-15 mesoporous silica was developed. This method related the intensity of coloration of SBA-15 samples (after reached equilibrium sorption) within dye concentration in aqueous solution using Image-Pro Plus software. The sorption process of methyl violet dye onto SBA-15 was analyzed varying different initial parameters (dye concentration, mass of sorbent, pH of dye solution, and contact sorption time). SBA-15 proved as efficient sorbent for removal of methyl violet dye in contact time of 5 min, with maximum percentage of dye removal 99% at pH 8. The results obtained from Image-Pro Plus showed to be in good agreement with the sorption parameters obtained by UV/Vis spectroscopy, which has been the most commonly used instrument for quantification of dye sorption. The image analysis method proved well prediction of dye concentrations with maximum relative error of 1.83 %. The advantages of this method are low cost and reliable quantitative evaluation with minimum of time.",
publisher = "Springer",
journal = "Environmental Monitoring and Assessment",
title = "New method for quantification of dye sorption using SBA mesoporous silica as a target sorbent",
volume = "188",
number = "3",
doi = "10.1007/s10661-016-5155-0"
}

Nešić, A., Kokunešoski, M., Volkov-Husović, T.,& Veličković, S. J.. (2016). New method for quantification of dye sorption using SBA mesoporous silica as a target sorbent. in Environmental Monitoring and Assessment
Springer., 188(3).
https://doi.org/10.1007/s10661-016-5155-0

Nešić A, Kokunešoski M, Volkov-Husović T, Veličković SJ. New method for quantification of dye sorption using SBA mesoporous silica as a target sorbent. in Environmental Monitoring and Assessment. 2016;188(3).
doi:10.1007/s10661-016-5155-0 .

Nešić, Aleksandra, Kokunešoski, Maja, Volkov-Husović, Tatjana, Veličković, Sava J., "New method for quantification of dye sorption using SBA mesoporous silica as a target sorbent" in Environmental Monitoring and Assessment, 188, no. 3 (2016),
https://doi.org/10.1007/s10661-016-5155-0 . .

TY  - JOUR
AU  - Cocic, Mira
AU  - Logar, Mihovil
AU  - Matović, Branko
AU  - Devic, Snezana
AU  - Volkov-Husović, Tatjana
AU  - Cocic, Sasa
AU  - Tasic, Visa
PY  - 2016
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1228
AB  - In the copper extraction, especially during the process of flotation enrichment and the pyrometallurgical processing, the waste materials that represent huge polluters of environment are being generated. In order to examine the application of Final flotation waste (FFW) in the manufacturing of new materials from the glass-ceramic group phase and mineral composition were examined as well as thermal properties. FFW kinetics of sintering has been tested at different dyamics (1 degrees C/min, 29 degrees C/min and 43 degrees C/min), in order to find the optimum conditions for sintering with a minimum amount of energy and time consumption. The samples were examined using: X-ray diffraction, X-ray fluorescence analysis, SEM (Scanning Electron Microscopy) and thermal microscopy. The best results for the production of glass ceramic materials were obtained during the sintering at heating regime of 29 degrees C/min.
T2  - Science of Sintering
T1  - Final Flotation Waste Kinetics of Sintering at Different Heating Regimes
VL  - 48
IS  - 2
SP  - 197
EP  - 208
DO  - 10.2298/SOS1602197C
ER  - 

@article{
author = "Cocic, Mira and Logar, Mihovil and Matović, Branko and Devic, Snezana and Volkov-Husović, Tatjana and Cocic, Sasa and Tasic, Visa",
year = "2016",
abstract = "In the copper extraction, especially during the process of flotation enrichment and the pyrometallurgical processing, the waste materials that represent huge polluters of environment are being generated. In order to examine the application of Final flotation waste (FFW) in the manufacturing of new materials from the glass-ceramic group phase and mineral composition were examined as well as thermal properties. FFW kinetics of sintering has been tested at different dyamics (1 degrees C/min, 29 degrees C/min and 43 degrees C/min), in order to find the optimum conditions for sintering with a minimum amount of energy and time consumption. The samples were examined using: X-ray diffraction, X-ray fluorescence analysis, SEM (Scanning Electron Microscopy) and thermal microscopy. The best results for the production of glass ceramic materials were obtained during the sintering at heating regime of 29 degrees C/min.",
journal = "Science of Sintering",
title = "Final Flotation Waste Kinetics of Sintering at Different Heating Regimes",
volume = "48",
number = "2",
pages = "197-208",
doi = "10.2298/SOS1602197C"
}

Cocic, M., Logar, M., Matović, B., Devic, S., Volkov-Husović, T., Cocic, S.,& Tasic, V.. (2016). Final Flotation Waste Kinetics of Sintering at Different Heating Regimes. in Science of Sintering, 48(2), 197-208.
https://doi.org/10.2298/SOS1602197C

Cocic M, Logar M, Matović B, Devic S, Volkov-Husović T, Cocic S, Tasic V. Final Flotation Waste Kinetics of Sintering at Different Heating Regimes. in Science of Sintering. 2016;48(2):197-208.
doi:10.2298/SOS1602197C .

Cocic, Mira, Logar, Mihovil, Matović, Branko, Devic, Snezana, Volkov-Husović, Tatjana, Cocic, Sasa, Tasic, Visa, "Final Flotation Waste Kinetics of Sintering at Different Heating Regimes" in Science of Sintering, 48, no. 2 (2016):197-208,
https://doi.org/10.2298/SOS1602197C . .