TY  - JOUR
AU  - Popović, Maja
AU  - Novaković, Mirjana
AU  - Pjević, Dejan
AU  - Vana, Dušan
AU  - Jugović, Dragana
AU  - Tošić, Dragana
AU  - Noga, Pavol
PY  - 2024
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/12279
AB  - In the present paper, the effects of metal ion implantation on the structural and optical properties of TiN thin films have been investigated. TiN films of 170 nm thickness were grown by d.c. reactive sputtering on Si (100) wafers and then irradiated at 5 × 1016 ions/cm2 with either Au, Ag, or Cu ions by using two different energies per each implanted metal. The results showed that as deposited TiN crystallizes in the form of a fcc cubic structure, with the crystallites preferentially oriented along the (111) plane. For all implanted layers, the cubic structure was preserved, but compared to as deposited TiN the crystallites were smaller and the lattice was contracted. These changes were correlated with the depth distribution of Au, Ag and Cu ions and assigned to implantation-induced damage that was larger when higher ion energies were used. High-resolution XPS spectra of the surface of as deposited sample showed the coexistence of TiN, TiO2 and TiOxNy phases and this was related to the surface oxidation of the films due to the exposure to air. After implantation, the results were almost similar for all metals, showing an increase in TiO2 contribution and the formation of pure metallic Au and Ag phases, while copper is in the Cu2+ state, which is attributed to Cu(II)-oxide and Cu(OH)2. The microstructural characteristics including defect formation, changes in crystallite size and lattice contraction, and also growth of different metallic phases during implantations were correlated with the findings of the optical characterization of the implanted films. For the as deposited film we found an energy gap of 2.91 eV, which was lower than the value typical for TiN. After implantation the gap was shifted to higher energies, while at the visible part of the region, the existence of additional energy levels, at photon energies below 2.9 eV was observed. Besides, all implanted films showed degraded photocatalytic activity compared to as deposited TiN, among which Cu-implanted samples exhibited the best photocatalytic performances. The lower photocatalytic activity of Au and Ag implanted films compared to Cu implantations was ascribed to larger structural defects and the formation of less favorable electronic states.
T2  - Journal of Alloys and Compounds
T1  - Investigating on the microstructure and optical properties of Au, Ag and Cu implanted TiN thin films: The effects of surface oxidation and ion-induced defects
VL  - 976
SP  - 173046
DO  - 10.1016/j.jallcom.2023.173046
ER  - 

@article{
author = "Popović, Maja and Novaković, Mirjana and Pjević, Dejan and Vana, Dušan and Jugović, Dragana and Tošić, Dragana and Noga, Pavol",
year = "2024",
abstract = "In the present paper, the effects of metal ion implantation on the structural and optical properties of TiN thin films have been investigated. TiN films of 170 nm thickness were grown by d.c. reactive sputtering on Si (100) wafers and then irradiated at 5 × 1016 ions/cm2 with either Au, Ag, or Cu ions by using two different energies per each implanted metal. The results showed that as deposited TiN crystallizes in the form of a fcc cubic structure, with the crystallites preferentially oriented along the (111) plane. For all implanted layers, the cubic structure was preserved, but compared to as deposited TiN the crystallites were smaller and the lattice was contracted. These changes were correlated with the depth distribution of Au, Ag and Cu ions and assigned to implantation-induced damage that was larger when higher ion energies were used. High-resolution XPS spectra of the surface of as deposited sample showed the coexistence of TiN, TiO2 and TiOxNy phases and this was related to the surface oxidation of the films due to the exposure to air. After implantation, the results were almost similar for all metals, showing an increase in TiO2 contribution and the formation of pure metallic Au and Ag phases, while copper is in the Cu2+ state, which is attributed to Cu(II)-oxide and Cu(OH)2. The microstructural characteristics including defect formation, changes in crystallite size and lattice contraction, and also growth of different metallic phases during implantations were correlated with the findings of the optical characterization of the implanted films. For the as deposited film we found an energy gap of 2.91 eV, which was lower than the value typical for TiN. After implantation the gap was shifted to higher energies, while at the visible part of the region, the existence of additional energy levels, at photon energies below 2.9 eV was observed. Besides, all implanted films showed degraded photocatalytic activity compared to as deposited TiN, among which Cu-implanted samples exhibited the best photocatalytic performances. The lower photocatalytic activity of Au and Ag implanted films compared to Cu implantations was ascribed to larger structural defects and the formation of less favorable electronic states.",
journal = "Journal of Alloys and Compounds",
title = "Investigating on the microstructure and optical properties of Au, Ag and Cu implanted TiN thin films: The effects of surface oxidation and ion-induced defects",
volume = "976",
pages = "173046",
doi = "10.1016/j.jallcom.2023.173046"
}

Popović, M., Novaković, M., Pjević, D., Vana, D., Jugović, D., Tošić, D.,& Noga, P.. (2024). Investigating on the microstructure and optical properties of Au, Ag and Cu implanted TiN thin films: The effects of surface oxidation and ion-induced defects. in Journal of Alloys and Compounds, 976, 173046.
https://doi.org/10.1016/j.jallcom.2023.173046

Popović M, Novaković M, Pjević D, Vana D, Jugović D, Tošić D, Noga P. Investigating on the microstructure and optical properties of Au, Ag and Cu implanted TiN thin films: The effects of surface oxidation and ion-induced defects. in Journal of Alloys and Compounds. 2024;976:173046.
doi:10.1016/j.jallcom.2023.173046 .

Popović, Maja, Novaković, Mirjana, Pjević, Dejan, Vana, Dušan, Jugović, Dragana, Tošić, Dragana, Noga, Pavol, "Investigating on the microstructure and optical properties of Au, Ag and Cu implanted TiN thin films: The effects of surface oxidation and ion-induced defects" in Journal of Alloys and Compounds, 976 (2024):173046,
https://doi.org/10.1016/j.jallcom.2023.173046 . .

TY  - JOUR
AU  - Popović, Maja
AU  - Novaković, Mirjana M.
AU  - Vaňa, Dušan
AU  - Ronning, Carsten
AU  - Jugović, Dragana
AU  - Rajić, Vladimir
AU  - Noga, Pavol
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10746
AB  - Titanium nitride (TiN) is an attractive alternative for modern and future photonic applications, as its optical properties can be engineered over a wide spectral range. In this study, we have used sequential implantation of gold and silver ions with varying ion fluence, as well as subsequent annealing, in order to modify the optical and plasmonic properties of TiN thin films and correlated this to their structural properties. Our investigations show that the columnar structure of the TiN films is partially destroyed upon implantation, but metallic Au and Ag nanoparticles are formed. The irradiation further induces a reduction of the lattice constant as well as changes the TiN stoichiometry and grain size. From the optical point of view, the implanted films possess less metallicity with increasing Ag fluence and losses several times lower than the as-deposited film, which can be correlated with the deficiency of nitrogen and additional defects. Subsequent annealing partially recovered the destroyed columnar structure, and the films become more metallic where the optical losses are much smaller in comparison to the as-implanted situation, being comparable to those of pure Au and Ag. In this way, by varying the implantation fluence of silver ions properly while keeping the gold fluence constant, we were able to optimize experimental parameters in such a way to ensure the formation of TiN with desirable optical performances.
T2  - Optical Materials
T1  - Structure-dependent optical properties of Au/Ag irradiated TiN thin films
VL  - 138
SP  - 113684
DO  - 10.1016/j.optmat.2023.113684
UR  - https://hdl.handle.net/21.15107/rcub_dais_14289
ER  - 

@article{
author = "Popović, Maja and Novaković, Mirjana M. and Vaňa, Dušan and Ronning, Carsten and Jugović, Dragana and Rajić, Vladimir and Noga, Pavol",
year = "2023",
abstract = "Titanium nitride (TiN) is an attractive alternative for modern and future photonic applications, as its optical properties can be engineered over a wide spectral range. In this study, we have used sequential implantation of gold and silver ions with varying ion fluence, as well as subsequent annealing, in order to modify the optical and plasmonic properties of TiN thin films and correlated this to their structural properties. Our investigations show that the columnar structure of the TiN films is partially destroyed upon implantation, but metallic Au and Ag nanoparticles are formed. The irradiation further induces a reduction of the lattice constant as well as changes the TiN stoichiometry and grain size. From the optical point of view, the implanted films possess less metallicity with increasing Ag fluence and losses several times lower than the as-deposited film, which can be correlated with the deficiency of nitrogen and additional defects. Subsequent annealing partially recovered the destroyed columnar structure, and the films become more metallic where the optical losses are much smaller in comparison to the as-implanted situation, being comparable to those of pure Au and Ag. In this way, by varying the implantation fluence of silver ions properly while keeping the gold fluence constant, we were able to optimize experimental parameters in such a way to ensure the formation of TiN with desirable optical performances.",
journal = "Optical Materials",
title = "Structure-dependent optical properties of Au/Ag irradiated TiN thin films",
volume = "138",
pages = "113684",
doi = "10.1016/j.optmat.2023.113684",
url = "https://hdl.handle.net/21.15107/rcub_dais_14289"
}

Popović, M., Novaković, M. M., Vaňa, D., Ronning, C., Jugović, D., Rajić, V.,& Noga, P.. (2023). Structure-dependent optical properties of Au/Ag irradiated TiN thin films. in Optical Materials, 138, 113684.
https://doi.org/10.1016/j.optmat.2023.113684
https://hdl.handle.net/21.15107/rcub_dais_14289

Popović M, Novaković MM, Vaňa D, Ronning C, Jugović D, Rajić V, Noga P. Structure-dependent optical properties of Au/Ag irradiated TiN thin films. in Optical Materials. 2023;138:113684.
doi:10.1016/j.optmat.2023.113684
https://hdl.handle.net/21.15107/rcub_dais_14289 .

Popović, Maja, Novaković, Mirjana M., Vaňa, Dušan, Ronning, Carsten, Jugović, Dragana, Rajić, Vladimir, Noga, Pavol, "Structure-dependent optical properties of Au/Ag irradiated TiN thin films" in Optical Materials, 138 (2023):113684,
https://doi.org/10.1016/j.optmat.2023.113684 .,
https://hdl.handle.net/21.15107/rcub_dais_14289 .

TY  - CONF
AU  - Popović, M.
AU  - Novaković, Mirjana
AU  - Pjević, Dejan
AU  - Vana, D.
AU  - Jugović, Dragana
AU  - Noga, Pavol
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/11805
AB  - The ion implantation technique has a number of advantages over conventional methods for the improvement of thin films that offer the various possibilities of their use in different industrial and technological fields. Herein, we present the effects of metal ion implantation on the structural and optical properties of TiN thin films. TiN films of 170 nm thickness were grown by d.c. reactive sputtering on Si (100) wafers and then irradiated at 5×1016 ions/cm2 with either Au, Ag, or Cu ions by using two different energies per each implanted metal. The results showed that as deposited TiN crystallizes in form of fcc cubic structure, with the crystallites preferentially oriented along the (111) plane. For all implanted layers the cubic crystallographic structure was preserved, but compared to as deposited TiN the crystallites were smaller and the lattice was contracted. Besides, the surface compositional analysis of as deposited sample showed the coexistence of TiN, TiO2 and TiOxNy phases and this was related to the surface oxidation of the films due to the exposure to air. After implantation, the results were almost similar for all metals, showing an increase in TiO2 contribution and the formation of pure metallic Au and Ag phases, while copper is in the Cu2+ state, which is attributed to Cu(II)-oxide and Cu(OH)2. The microstructural characteristics including defect formation, changes in the crystallite size and lattice contraction, and also growth of different metallic phases during implantations were correlated with the findings of the optical characterization of the implanted films. For as deposited film we found energy gap of 2.91 eV, which was lower than the value typical for TiN. After implantation the gap was shifted to higher energies, while at the visible part of the region, additional energy levels, at photon energies below 2.9 eV were observed. Further, all implanted films showed degraded photocatalytic activity compared to as deposited TiN, among which Cu-implanted samples exhibited the best photocatalytic performances. The lower photocatalytic activity of Au and Ag-implanted films compared to Cu implantations was ascribed to larger structural defects and formation of less favorable electronic states.
PB  - Belgrade : Vinča Institute of Nuclear Sciences
C3  - PHOTONICA2023 : 9th International School and Conference on Photonics : book of abstracts; August 28 - September 1, 2023; Belgrade
T1  - Metal ion-implanted TiN thin films: Induced effects on structural and optical properties
SP  - 63
EP  - 63
UR  - https://hdl.handle.net/21.15107/rcub_vinar_11805
ER  - 

@conference{
author = "Popović, M. and Novaković, Mirjana and Pjević, Dejan and Vana, D. and Jugović, Dragana and Noga, Pavol",
year = "2023",
abstract = "The ion implantation technique has a number of advantages over conventional methods for the improvement of thin films that offer the various possibilities of their use in different industrial and technological fields. Herein, we present the effects of metal ion implantation on the structural and optical properties of TiN thin films. TiN films of 170 nm thickness were grown by d.c. reactive sputtering on Si (100) wafers and then irradiated at 5×1016 ions/cm2 with either Au, Ag, or Cu ions by using two different energies per each implanted metal. The results showed that as deposited TiN crystallizes in form of fcc cubic structure, with the crystallites preferentially oriented along the (111) plane. For all implanted layers the cubic crystallographic structure was preserved, but compared to as deposited TiN the crystallites were smaller and the lattice was contracted. Besides, the surface compositional analysis of as deposited sample showed the coexistence of TiN, TiO2 and TiOxNy phases and this was related to the surface oxidation of the films due to the exposure to air. After implantation, the results were almost similar for all metals, showing an increase in TiO2 contribution and the formation of pure metallic Au and Ag phases, while copper is in the Cu2+ state, which is attributed to Cu(II)-oxide and Cu(OH)2. The microstructural characteristics including defect formation, changes in the crystallite size and lattice contraction, and also growth of different metallic phases during implantations were correlated with the findings of the optical characterization of the implanted films. For as deposited film we found energy gap of 2.91 eV, which was lower than the value typical for TiN. After implantation the gap was shifted to higher energies, while at the visible part of the region, additional energy levels, at photon energies below 2.9 eV were observed. Further, all implanted films showed degraded photocatalytic activity compared to as deposited TiN, among which Cu-implanted samples exhibited the best photocatalytic performances. The lower photocatalytic activity of Au and Ag-implanted films compared to Cu implantations was ascribed to larger structural defects and formation of less favorable electronic states.",
publisher = "Belgrade : Vinča Institute of Nuclear Sciences",
journal = "PHOTONICA2023 : 9th International School and Conference on Photonics : book of abstracts; August 28 - September 1, 2023; Belgrade",
title = "Metal ion-implanted TiN thin films: Induced effects on structural and optical properties",
pages = "63-63",
url = "https://hdl.handle.net/21.15107/rcub_vinar_11805"
}

Popović, M., Novaković, M., Pjević, D., Vana, D., Jugović, D.,& Noga, P.. (2023). Metal ion-implanted TiN thin films: Induced effects on structural and optical properties. in PHOTONICA2023 : 9th International School and Conference on Photonics : book of abstracts; August 28 - September 1, 2023; Belgrade
Belgrade : Vinča Institute of Nuclear Sciences., 63-63.
https://hdl.handle.net/21.15107/rcub_vinar_11805

Popović M, Novaković M, Pjević D, Vana D, Jugović D, Noga P. Metal ion-implanted TiN thin films: Induced effects on structural and optical properties. in PHOTONICA2023 : 9th International School and Conference on Photonics : book of abstracts; August 28 - September 1, 2023; Belgrade. 2023;:63-63.
https://hdl.handle.net/21.15107/rcub_vinar_11805 .

Popović, M., Novaković, Mirjana, Pjević, Dejan, Vana, D., Jugović, Dragana, Noga, Pavol, "Metal ion-implanted TiN thin films: Induced effects on structural and optical properties" in PHOTONICA2023 : 9th International School and Conference on Photonics : book of abstracts; August 28 - September 1, 2023; Belgrade (2023):63-63,
https://hdl.handle.net/21.15107/rcub_vinar_11805 .

TY  - CONF
AU  - Stanić, Vojislav
AU  - Omerašević, Mia
AU  - Mutavdžić, Dragoslav
AU  - Jugović, Dragana
AU  - Bučevac, Dušan
AU  - Gerić, Tamara
AU  - Jelić, Ivana
PY  - 2023
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/11647
AB  - Praseodymium doped calcium hydroxyapatite (PrHAP) nanopowder was synthesized by the co-precipitation method and characterized by X-Ray Diffraction, Fourier Transform Infrared, and Fluorescence Spectroscopy. Characterization studies from XRD and FTIR spectra showed that obtained crystals are monophase hydroxyapatites and that the sample particles are of nano size. A fluorescence study has shown that PrHAP particles have fluorescent emission under UV‐ Visible excitation. These results may open new avenues for developing bioactive materials for bone regeneration and fluorescent probes for bio-imaging applications
PB  - Belgrade : Serbian Ceramic Society
C3  - Advanced Ceramics and Application :11th Serbian Ceramic Society Conference : program and the book of abstracts; September 18-20, 2023; Belgrade
T1  - Synthesis and characterization of luminescent Pr3+ –doped hydroxyapatite nanopowder as a potential biomaterial for bioimaging applications
SP  - 72
UR  - https://hdl.handle.net/21.15107/rcub_vinar_11647
ER  - 

@conference{
author = "Stanić, Vojislav and Omerašević, Mia and Mutavdžić, Dragoslav and Jugović, Dragana and Bučevac, Dušan and Gerić, Tamara and Jelić, Ivana",
year = "2023",
abstract = "Praseodymium doped calcium hydroxyapatite (PrHAP) nanopowder was synthesized by the co-precipitation method and characterized by X-Ray Diffraction, Fourier Transform Infrared, and Fluorescence Spectroscopy. Characterization studies from XRD and FTIR spectra showed that obtained crystals are monophase hydroxyapatites and that the sample particles are of nano size. A fluorescence study has shown that PrHAP particles have fluorescent emission under UV‐ Visible excitation. These results may open new avenues for developing bioactive materials for bone regeneration and fluorescent probes for bio-imaging applications",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Advanced Ceramics and Application :11th Serbian Ceramic Society Conference : program and the book of abstracts; September 18-20, 2023; Belgrade",
title = "Synthesis and characterization of luminescent Pr3+ –doped hydroxyapatite nanopowder as a potential biomaterial for bioimaging applications",
pages = "72",
url = "https://hdl.handle.net/21.15107/rcub_vinar_11647"
}

Stanić, V., Omerašević, M., Mutavdžić, D., Jugović, D., Bučevac, D., Gerić, T.,& Jelić, I.. (2023). Synthesis and characterization of luminescent Pr3+ –doped hydroxyapatite nanopowder as a potential biomaterial for bioimaging applications. in Advanced Ceramics and Application :11th Serbian Ceramic Society Conference : program and the book of abstracts; September 18-20, 2023; Belgrade
Belgrade : Serbian Ceramic Society., 72.
https://hdl.handle.net/21.15107/rcub_vinar_11647

Stanić V, Omerašević M, Mutavdžić D, Jugović D, Bučevac D, Gerić T, Jelić I. Synthesis and characterization of luminescent Pr3+ –doped hydroxyapatite nanopowder as a potential biomaterial for bioimaging applications. in Advanced Ceramics and Application :11th Serbian Ceramic Society Conference : program and the book of abstracts; September 18-20, 2023; Belgrade. 2023;:72.
https://hdl.handle.net/21.15107/rcub_vinar_11647 .

Stanić, Vojislav, Omerašević, Mia, Mutavdžić, Dragoslav, Jugović, Dragana, Bučevac, Dušan, Gerić, Tamara, Jelić, Ivana, "Synthesis and characterization of luminescent Pr3+ –doped hydroxyapatite nanopowder as a potential biomaterial for bioimaging applications" in Advanced Ceramics and Application :11th Serbian Ceramic Society Conference : program and the book of abstracts; September 18-20, 2023; Belgrade (2023):72,
https://hdl.handle.net/21.15107/rcub_vinar_11647 .

TY  - JOUR
AU  - Jugović, Dragana
AU  - Milović, Miloš
AU  - Barudžija, Tanja
AU  - Kuzmanović, Maja
AU  - Vujković, Milica
AU  - Mitrić, Miodrag
PY  - 2022
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10577
AB  - Layered VOPO4·2H2O is synthesized by the sonochemical method. An X-ray powder diffraction is used to examine the crystal structure, while scanning electron microscopy is used to reveal the morphology of the powder. The crystal structure refinement is performed in the P4/nmmZ space group. The electrochemical intercalation of several cations (Na+, Mg2+, Ca2+, and Al3+) in saturated nitrate aqueous solutions is investigated. The most notable reversible activity is found for the cycling in aluminium nitrate aqueous solution in the voltage range from −0.1 to 0.8 V vs. SCE. During the preparation of the electrode, it is observed that the structure is prone to changes that have not been recorded in the literature so far. Namely, the use of conventional binder PVDF in NMP solution deteriorates the structure and lowers the powder’s crystallinity, while the use of Nafion solution causes the rearrangement of the atoms in a new crystal form that can be described in the monoclinic P21/c space group. Consequently, these structural changes affect electrochemical performances. The observed differences in electrochemical performances are a result of structural rearrangements.
T2  - Materials
T1  - The Influence of a Binder in a Composite Electrode: The Case Study of Vanadyl Phosphate in Aqueous Electrolyte
VL  - 15
IS  - 24
SP  - 9041
DO  - 10.3390/ma15249041
ER  - 

@article{
author = "Jugović, Dragana and Milović, Miloš and Barudžija, Tanja and Kuzmanović, Maja and Vujković, Milica and Mitrić, Miodrag",
year = "2022",
abstract = "Layered VOPO4·2H2O is synthesized by the sonochemical method. An X-ray powder diffraction is used to examine the crystal structure, while scanning electron microscopy is used to reveal the morphology of the powder. The crystal structure refinement is performed in the P4/nmmZ space group. The electrochemical intercalation of several cations (Na+, Mg2+, Ca2+, and Al3+) in saturated nitrate aqueous solutions is investigated. The most notable reversible activity is found for the cycling in aluminium nitrate aqueous solution in the voltage range from −0.1 to 0.8 V vs. SCE. During the preparation of the electrode, it is observed that the structure is prone to changes that have not been recorded in the literature so far. Namely, the use of conventional binder PVDF in NMP solution deteriorates the structure and lowers the powder’s crystallinity, while the use of Nafion solution causes the rearrangement of the atoms in a new crystal form that can be described in the monoclinic P21/c space group. Consequently, these structural changes affect electrochemical performances. The observed differences in electrochemical performances are a result of structural rearrangements.",
journal = "Materials",
title = "The Influence of a Binder in a Composite Electrode: The Case Study of Vanadyl Phosphate in Aqueous Electrolyte",
volume = "15",
number = "24",
pages = "9041",
doi = "10.3390/ma15249041"
}

Jugović, D., Milović, M., Barudžija, T., Kuzmanović, M., Vujković, M.,& Mitrić, M.. (2022). The Influence of a Binder in a Composite Electrode: The Case Study of Vanadyl Phosphate in Aqueous Electrolyte. in Materials, 15(24), 9041.
https://doi.org/10.3390/ma15249041

Jugović D, Milović M, Barudžija T, Kuzmanović M, Vujković M, Mitrić M. The Influence of a Binder in a Composite Electrode: The Case Study of Vanadyl Phosphate in Aqueous Electrolyte. in Materials. 2022;15(24):9041.
doi:10.3390/ma15249041 .

Jugović, Dragana, Milović, Miloš, Barudžija, Tanja, Kuzmanović, Maja, Vujković, Milica, Mitrić, Miodrag, "The Influence of a Binder in a Composite Electrode: The Case Study of Vanadyl Phosphate in Aqueous Electrolyte" in Materials, 15, no. 24 (2022):9041,
https://doi.org/10.3390/ma15249041 . .

TY  - JOUR
AU  - Jugović, Dragana
AU  - Milović, Miloš
AU  - Ivanovski, Valentin N.
AU  - Škapin, Srečo Davor
AU  - Barudžija, Tanja
AU  - Mitrić, Miodrag
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9921
AB  - Fayalite Fe2SiO4 is synthesized by the solid-state reaction without ball milling. The obtained powder is further structurally and electrochemically examined. Field emission scanning electron microscopy (FESEM) showed that microsized powder is obtained. X-ray powder diffraction (XRD) pattern is used for both phase identification and crystal structure Rietveld refinement. The structure is refined in the orthorhombic Pbnm space group. Mössbauer spectroscopy revealed traces of Fe3+ impurity. The bond valence mapping method is applied for the first time on Fe2SiO4 framework. It shows isolated, non-connected isosurfaces of constant E(Li), which further supports the assumptions of the conversion reactions. Electrochemical performances are investigated through galvanostatic cycling, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). Ex-situ XRD and Fourier transform infrared spectroscopy (FTIR) analyses are combined to monitor phase change after galvanostatic cycling and to reveal the working mechanism during electrochemical lithiation.
T2  - Journal of Electroceramics
T1  - Microsized fayalite Fe2SiO4 as anode material: the structure, electrochemical properties and working mechanism
DO  - 10.1007/s10832-021-00260-9
ER  - 

@article{
author = "Jugović, Dragana and Milović, Miloš and Ivanovski, Valentin N. and Škapin, Srečo Davor and Barudžija, Tanja and Mitrić, Miodrag",
year = "2021",
abstract = "Fayalite Fe2SiO4 is synthesized by the solid-state reaction without ball milling. The obtained powder is further structurally and electrochemically examined. Field emission scanning electron microscopy (FESEM) showed that microsized powder is obtained. X-ray powder diffraction (XRD) pattern is used for both phase identification and crystal structure Rietveld refinement. The structure is refined in the orthorhombic Pbnm space group. Mössbauer spectroscopy revealed traces of Fe3+ impurity. The bond valence mapping method is applied for the first time on Fe2SiO4 framework. It shows isolated, non-connected isosurfaces of constant E(Li), which further supports the assumptions of the conversion reactions. Electrochemical performances are investigated through galvanostatic cycling, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). Ex-situ XRD and Fourier transform infrared spectroscopy (FTIR) analyses are combined to monitor phase change after galvanostatic cycling and to reveal the working mechanism during electrochemical lithiation.",
journal = "Journal of Electroceramics",
title = "Microsized fayalite Fe2SiO4 as anode material: the structure, electrochemical properties and working mechanism",
doi = "10.1007/s10832-021-00260-9"
}

Jugović, D., Milović, M., Ivanovski, V. N., Škapin, S. D., Barudžija, T.,& Mitrić, M.. (2021). Microsized fayalite Fe2SiO4 as anode material: the structure, electrochemical properties and working mechanism. in Journal of Electroceramics.
https://doi.org/10.1007/s10832-021-00260-9

Jugović D, Milović M, Ivanovski VN, Škapin SD, Barudžija T, Mitrić M. Microsized fayalite Fe2SiO4 as anode material: the structure, electrochemical properties and working mechanism. in Journal of Electroceramics. 2021;.
doi:10.1007/s10832-021-00260-9 .

Jugović, Dragana, Milović, Miloš, Ivanovski, Valentin N., Škapin, Srečo Davor, Barudžija, Tanja, Mitrić, Miodrag, "Microsized fayalite Fe2SiO4 as anode material: the structure, electrochemical properties and working mechanism" in Journal of Electroceramics (2021),
https://doi.org/10.1007/s10832-021-00260-9 . .

TY  - JOUR
AU  - Rakočević, Lazar
AU  - Štrbac, Svetlana
AU  - Potočnik, Jelena
AU  - Popović, Maja
AU  - Jugović, Dragana
AU  - Stojković-Simatović, Ivana
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10203
AB  - Cathodic material for sodium-ion rechargeable batteries based on NaxMnO2 were synthesized by glycine nitrate method and subsequent annealing at high temperatures. Different crystal structures with different morphologies were obtained depending on the annealing temperature: hexagonal layeredα-Na0.7MnO2.05 nanoplates were obtained at 850 ◦C, while 3-D tunnel structured Na0⋅4MnO2 and Na0⋅44MnO2, both with rod-like morphology, were obtained at 800 ◦C and 900 ◦C, respectively. The investigations of the electrochemical behavior of obtained cathodic materials in aqueous NaNO3 solution have shown that Na0⋅44MnO2 obtained at 900 ◦C has shown the best battery performance. Its initial discharge capacities are 123.5 mA h/g, 113.2 mA h/g, and 102.0 mA h/g at the high current densities of 1000, 2000 and 5000 mA/g, respectively.
T2  - Ceramics International
T1  - The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries
VL  - 47
IS  - 4
SP  - 4595
EP  - 4603
DO  - 10.1016/j.ceramint.2020.10.025
UR  - https://hdl.handle.net/21.15107/rcub_dais_11229
ER  - 

@article{
author = "Rakočević, Lazar and Štrbac, Svetlana and Potočnik, Jelena and Popović, Maja and Jugović, Dragana and Stojković-Simatović, Ivana",
year = "2021",
abstract = "Cathodic material for sodium-ion rechargeable batteries based on NaxMnO2 were synthesized by glycine nitrate method and subsequent annealing at high temperatures. Different crystal structures with different morphologies were obtained depending on the annealing temperature: hexagonal layeredα-Na0.7MnO2.05 nanoplates were obtained at 850 ◦C, while 3-D tunnel structured Na0⋅4MnO2 and Na0⋅44MnO2, both with rod-like morphology, were obtained at 800 ◦C and 900 ◦C, respectively. The investigations of the electrochemical behavior of obtained cathodic materials in aqueous NaNO3 solution have shown that Na0⋅44MnO2 obtained at 900 ◦C has shown the best battery performance. Its initial discharge capacities are 123.5 mA h/g, 113.2 mA h/g, and 102.0 mA h/g at the high current densities of 1000, 2000 and 5000 mA/g, respectively.",
journal = "Ceramics International",
title = "The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries",
volume = "47",
number = "4",
pages = "4595-4603",
doi = "10.1016/j.ceramint.2020.10.025",
url = "https://hdl.handle.net/21.15107/rcub_dais_11229"
}

Rakočević, L., Štrbac, S., Potočnik, J., Popović, M., Jugović, D.,& Stojković-Simatović, I.. (2021). The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries. in Ceramics International, 47(4), 4595-4603.
https://doi.org/10.1016/j.ceramint.2020.10.025
https://hdl.handle.net/21.15107/rcub_dais_11229

Rakočević L, Štrbac S, Potočnik J, Popović M, Jugović D, Stojković-Simatović I. The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries. in Ceramics International. 2021;47(4):4595-4603.
doi:10.1016/j.ceramint.2020.10.025
https://hdl.handle.net/21.15107/rcub_dais_11229 .

Rakočević, Lazar, Štrbac, Svetlana, Potočnik, Jelena, Popović, Maja, Jugović, Dragana, Stojković-Simatović, Ivana, "The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries" in Ceramics International, 47, no. 4 (2021):4595-4603,
https://doi.org/10.1016/j.ceramint.2020.10.025 .,
https://hdl.handle.net/21.15107/rcub_dais_11229 .

TY  - JOUR
AU  - Rakočević, Lazar
AU  - Štrbac, Svetlana
AU  - Potočnik, Jelena
AU  - Popović, Maja
AU  - Jugović, Dragana
AU  - Stojković-Simatović, Ivana
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10202
AB  - Cathodic material for sodium-ion rechargeable batteries based on NaxMnO2 were synthesized by glycine nitrate method and subsequent annealing at high temperatures. Different crystal structures with different morphologies were obtained depending on the annealing temperature: hexagonal layeredα-Na0.7MnO2.05 nanoplates were obtained at 850 ◦C, while 3-D tunnel structured Na0⋅4MnO2 and Na0⋅44MnO2, both with rod-like morphology, were obtained at 800 ◦C and 900 ◦C, respectively. The investigations of the electrochemical behavior of obtained cathodic materials in aqueous NaNO3 solution have shown that Na0⋅44MnO2 obtained at 900 ◦C has shown the best battery performance. Its initial discharge capacities are 123.5 mA h/g, 113.2 mA h/g, and 102.0 mA h/g at the high current densities of 1000, 2000 and 5000 mA/g, respectively.
T2  - Ceramics International
T1  - The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries
VL  - 47
IS  - 4
SP  - 4595
EP  - 4603
DO  - 10.1016/j.ceramint.2020.10.025
UR  - https://hdl.handle.net/21.15107/rcub_dais_11229
ER  - 

@article{
author = "Rakočević, Lazar and Štrbac, Svetlana and Potočnik, Jelena and Popović, Maja and Jugović, Dragana and Stojković-Simatović, Ivana",
year = "2021",
abstract = "Cathodic material for sodium-ion rechargeable batteries based on NaxMnO2 were synthesized by glycine nitrate method and subsequent annealing at high temperatures. Different crystal structures with different morphologies were obtained depending on the annealing temperature: hexagonal layeredα-Na0.7MnO2.05 nanoplates were obtained at 850 ◦C, while 3-D tunnel structured Na0⋅4MnO2 and Na0⋅44MnO2, both with rod-like morphology, were obtained at 800 ◦C and 900 ◦C, respectively. The investigations of the electrochemical behavior of obtained cathodic materials in aqueous NaNO3 solution have shown that Na0⋅44MnO2 obtained at 900 ◦C has shown the best battery performance. Its initial discharge capacities are 123.5 mA h/g, 113.2 mA h/g, and 102.0 mA h/g at the high current densities of 1000, 2000 and 5000 mA/g, respectively.",
journal = "Ceramics International",
title = "The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries",
volume = "47",
number = "4",
pages = "4595-4603",
doi = "10.1016/j.ceramint.2020.10.025",
url = "https://hdl.handle.net/21.15107/rcub_dais_11229"
}

Rakočević, L., Štrbac, S., Potočnik, J., Popović, M., Jugović, D.,& Stojković-Simatović, I.. (2021). The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries. in Ceramics International, 47(4), 4595-4603.
https://doi.org/10.1016/j.ceramint.2020.10.025
https://hdl.handle.net/21.15107/rcub_dais_11229

Rakočević L, Štrbac S, Potočnik J, Popović M, Jugović D, Stojković-Simatović I. The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries. in Ceramics International. 2021;47(4):4595-4603.
doi:10.1016/j.ceramint.2020.10.025
https://hdl.handle.net/21.15107/rcub_dais_11229 .

Rakočević, Lazar, Štrbac, Svetlana, Potočnik, Jelena, Popović, Maja, Jugović, Dragana, Stojković-Simatović, Ivana, "The NaxMnO2 materials prepared by a glycine-nitrate method as advanced cathode materials for aqueous sodium-ion rechargeable batteries" in Ceramics International, 47, no. 4 (2021):4595-4603,
https://doi.org/10.1016/j.ceramint.2020.10.025 .,
https://hdl.handle.net/21.15107/rcub_dais_11229 .

TY  - JOUR
AU  - Milović, Miloš
AU  - Vujković, Milica
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9148
AB  - Electrochemical and structural properties of LiV2O5 cathode were investigated. Obtained by solid state reaction at high temperature the material crystallized as gamma polymorph phase, γ-LiV2O5. The gamma structure provides two crystallographic sites to accommodate lithium ions, Li1 and Li2 position. Lithium insertion at these two sites occurs at two respective voltages versus lithium metal: ~3.6 V (Li1) and ~2.4 V (Li2). Intercalation at Li1 position is reversible in both organic and aqueous electrolyte and provides stable cycling performance at the high voltage. On the contrary, sluggish insertion/removal of Li+ at Li2 sites causes unstable performance and significant storage capacity fade at lower voltages. Lithium diffusion 3d landscape was determined by bond valence calculations applied on the γ-LiV2O5 phase, as well as on the metastable phases of γ′-V2O5 and ζ-Li2V2O5 that exist at high and low voltages respectively. The model was proposed based on inactivity of Li2 position of the metastable ζ-Li2V2O5 phase which provides explanation for the observed storage capacity loss at low voltages. © 2021 Elsevier Ltd and Techna Group S.r.l.
T2  - Ceramics International
T1  - Electrochemical and structural study on cycling performance of γ-LiV2O5 cathode
VL  - 47
IS  - 12
SP  - 17077
EP  - 17083
DO  - 10.1016/j.ceramint.2021.03.016
ER  - 

@article{
author = "Milović, Miloš and Vujković, Milica and Jugović, Dragana and Mitrić, Miodrag",
year = "2021",
abstract = "Electrochemical and structural properties of LiV2O5 cathode were investigated. Obtained by solid state reaction at high temperature the material crystallized as gamma polymorph phase, γ-LiV2O5. The gamma structure provides two crystallographic sites to accommodate lithium ions, Li1 and Li2 position. Lithium insertion at these two sites occurs at two respective voltages versus lithium metal: ~3.6 V (Li1) and ~2.4 V (Li2). Intercalation at Li1 position is reversible in both organic and aqueous electrolyte and provides stable cycling performance at the high voltage. On the contrary, sluggish insertion/removal of Li+ at Li2 sites causes unstable performance and significant storage capacity fade at lower voltages. Lithium diffusion 3d landscape was determined by bond valence calculations applied on the γ-LiV2O5 phase, as well as on the metastable phases of γ′-V2O5 and ζ-Li2V2O5 that exist at high and low voltages respectively. The model was proposed based on inactivity of Li2 position of the metastable ζ-Li2V2O5 phase which provides explanation for the observed storage capacity loss at low voltages. © 2021 Elsevier Ltd and Techna Group S.r.l.",
journal = "Ceramics International",
title = "Electrochemical and structural study on cycling performance of γ-LiV2O5 cathode",
volume = "47",
number = "12",
pages = "17077-17083",
doi = "10.1016/j.ceramint.2021.03.016"
}

Milović, M., Vujković, M., Jugović, D.,& Mitrić, M.. (2021). Electrochemical and structural study on cycling performance of γ-LiV2O5 cathode. in Ceramics International, 47(12), 17077-17083.
https://doi.org/10.1016/j.ceramint.2021.03.016

Milović M, Vujković M, Jugović D, Mitrić M. Electrochemical and structural study on cycling performance of γ-LiV2O5 cathode. in Ceramics International. 2021;47(12):17077-17083.
doi:10.1016/j.ceramint.2021.03.016 .

Milović, Miloš, Vujković, Milica, Jugović, Dragana, Mitrić, Miodrag, "Electrochemical and structural study on cycling performance of γ-LiV2O5 cathode" in Ceramics International, 47, no. 12 (2021):17077-17083,
https://doi.org/10.1016/j.ceramint.2021.03.016 . .

TY  - JOUR
AU  - Milović, Miloš
AU  - Jugović, Dragana
AU  - Vujković, Milica
AU  - Kuzmanović, Maja D.
AU  - Mraković, Ana Đ.
AU  - Mitrić, Miodrag
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/9799
AB  - The polyanion cathodes for Li-ion batteries, namely LiFePO4, Li2FeP2O7 and Li2FeSiO4, were synthesized by very short high-temperature treatment (approximately several minutes) and subsequent quenching. Methylcellulose—a polymer with thermally driven water solubility—was used as the medium in which the precursor solutions were dispersed prior to high temperature treatment. The methylcellulose pyrolytically decomposes to carbon, thus producing the polyanion material/carbon composites of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C. The obtained powders have reduced crystallinity and significant microstructural characteristics: low crystallite size and notable microstrain. They exhibit stable electrochemical performances in both aqueous and organic electrolyte. The broadening of existing peaks in cyclic voltammetry and/or the emergence of new broad peaks was attributed to the presence of the amorphous phase in the samples. In galvanostatic charge–discharge tests, the materials provided high capacities at low current densities, while the highest rate performance was demonstrated by olivine-phosphate when compared to the other two materials.
T2  - Bulletin of Materials Science
T1  - Towards a green and cost-effective synthesis of polyanionic cathodes: comparative electrochemical behaviour of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C synthesized using methylcellulose matrix
VL  - 44
IS  - 2
SP  - 144
DO  - 10.1007/s12034-021-02397-3
ER  - 

@article{
author = "Milović, Miloš and Jugović, Dragana and Vujković, Milica and Kuzmanović, Maja D. and Mraković, Ana Đ. and Mitrić, Miodrag",
year = "2021",
abstract = "The polyanion cathodes for Li-ion batteries, namely LiFePO4, Li2FeP2O7 and Li2FeSiO4, were synthesized by very short high-temperature treatment (approximately several minutes) and subsequent quenching. Methylcellulose—a polymer with thermally driven water solubility—was used as the medium in which the precursor solutions were dispersed prior to high temperature treatment. The methylcellulose pyrolytically decomposes to carbon, thus producing the polyanion material/carbon composites of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C. The obtained powders have reduced crystallinity and significant microstructural characteristics: low crystallite size and notable microstrain. They exhibit stable electrochemical performances in both aqueous and organic electrolyte. The broadening of existing peaks in cyclic voltammetry and/or the emergence of new broad peaks was attributed to the presence of the amorphous phase in the samples. In galvanostatic charge–discharge tests, the materials provided high capacities at low current densities, while the highest rate performance was demonstrated by olivine-phosphate when compared to the other two materials.",
journal = "Bulletin of Materials Science",
title = "Towards a green and cost-effective synthesis of polyanionic cathodes: comparative electrochemical behaviour of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C synthesized using methylcellulose matrix",
volume = "44",
number = "2",
pages = "144",
doi = "10.1007/s12034-021-02397-3"
}

Milović, M., Jugović, D., Vujković, M., Kuzmanović, M. D., Mraković, A. Đ.,& Mitrić, M.. (2021). Towards a green and cost-effective synthesis of polyanionic cathodes: comparative electrochemical behaviour of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C synthesized using methylcellulose matrix. in Bulletin of Materials Science, 44(2), 144.
https://doi.org/10.1007/s12034-021-02397-3

Milović M, Jugović D, Vujković M, Kuzmanović MD, Mraković AĐ, Mitrić M. Towards a green and cost-effective synthesis of polyanionic cathodes: comparative electrochemical behaviour of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C synthesized using methylcellulose matrix. in Bulletin of Materials Science. 2021;44(2):144.
doi:10.1007/s12034-021-02397-3 .

Milović, Miloš, Jugović, Dragana, Vujković, Milica, Kuzmanović, Maja D., Mraković, Ana Đ., Mitrić, Miodrag, "Towards a green and cost-effective synthesis of polyanionic cathodes: comparative electrochemical behaviour of LiFePO4/C, Li2FeP2O7/C and Li2FeSiO4/C synthesized using methylcellulose matrix" in Bulletin of Materials Science, 44, no. 2 (2021):144,
https://doi.org/10.1007/s12034-021-02397-3 . .

TY  - CONF
AU  - Milović, Miloš
AU  - Vujković, Milica
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
PY  - 2021
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/10842
AB  - For its capability to reversibly remove and insert lithium ions in the range of 0 ≤ x ≤ 1.4, gamma polymorph phase of Li x V2 O5 makes a solid candidate for cathode application in rechargeable batteries. Accommodation of lithium in concentrations higher than x ≈1.4 brings stability issues related to the transformation towards the metastable ζ phase, which significantly limits utilization of higher capacities the material could achieve. The presented investigation has been conducted on γ-LiV2 O5 powder obtained via solid state reaction at high temperatures. Structural refinement of the prepared γ phase has been carried out. Based on bond valence analysis of γ as well as of metastable γ’ and ζ phase, which occur at low and high lithium concentrations, respectively, mechanism is proposed for the observed capacity decrease. Electrochemical characteristics of γ-LiV2 O5 were investigated in both aqueous and organic electrolyte in the voltage range 4-2.3 V vs. Li + /Li in order to record performances of all three occurring phases, γ and both lithium poor γ’ (high voltage region) and lithium rich ζ (low voltage region). Ionic exchange of Li + with Mg2+ , Ca 2+ and Al 3+ in their respective aqueous electrolytes has been conducted to examine potential use of the material in the post- lithium rechargeable batteries.
PB  - Belgrade : Serbian Ceramic Society
C3  - Advanced Ceramics and Application : 9th Serbian Ceramic Society Conference : program and the book of abstracts; September 20-21, 2021; Belgrade
T1  - Structural and electrochemical properties of gamma LiV2O5 cathode
SP  - 84
UR  - https://hdl.handle.net/21.15107/rcub_vinar_10842
ER  - 

@conference{
author = "Milović, Miloš and Vujković, Milica and Jugović, Dragana and Mitrić, Miodrag",
year = "2021",
abstract = "For its capability to reversibly remove and insert lithium ions in the range of 0 ≤ x ≤ 1.4, gamma polymorph phase of Li x V2 O5 makes a solid candidate for cathode application in rechargeable batteries. Accommodation of lithium in concentrations higher than x ≈1.4 brings stability issues related to the transformation towards the metastable ζ phase, which significantly limits utilization of higher capacities the material could achieve. The presented investigation has been conducted on γ-LiV2 O5 powder obtained via solid state reaction at high temperatures. Structural refinement of the prepared γ phase has been carried out. Based on bond valence analysis of γ as well as of metastable γ’ and ζ phase, which occur at low and high lithium concentrations, respectively, mechanism is proposed for the observed capacity decrease. Electrochemical characteristics of γ-LiV2 O5 were investigated in both aqueous and organic electrolyte in the voltage range 4-2.3 V vs. Li + /Li in order to record performances of all three occurring phases, γ and both lithium poor γ’ (high voltage region) and lithium rich ζ (low voltage region). Ionic exchange of Li + with Mg2+ , Ca 2+ and Al 3+ in their respective aqueous electrolytes has been conducted to examine potential use of the material in the post- lithium rechargeable batteries.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Advanced Ceramics and Application : 9th Serbian Ceramic Society Conference : program and the book of abstracts; September 20-21, 2021; Belgrade",
title = "Structural and electrochemical properties of gamma LiV2O5 cathode",
pages = "84",
url = "https://hdl.handle.net/21.15107/rcub_vinar_10842"
}

Milović, M., Vujković, M., Jugović, D.,& Mitrić, M.. (2021). Structural and electrochemical properties of gamma LiV2O5 cathode. in Advanced Ceramics and Application : 9th Serbian Ceramic Society Conference : program and the book of abstracts; September 20-21, 2021; Belgrade
Belgrade : Serbian Ceramic Society., 84.
https://hdl.handle.net/21.15107/rcub_vinar_10842

Milović M, Vujković M, Jugović D, Mitrić M. Structural and electrochemical properties of gamma LiV2O5 cathode. in Advanced Ceramics and Application : 9th Serbian Ceramic Society Conference : program and the book of abstracts; September 20-21, 2021; Belgrade. 2021;:84.
https://hdl.handle.net/21.15107/rcub_vinar_10842 .

Milović, Miloš, Vujković, Milica, Jugović, Dragana, Mitrić, Miodrag, "Structural and electrochemical properties of gamma LiV2O5 cathode" in Advanced Ceramics and Application : 9th Serbian Ceramic Society Conference : program and the book of abstracts; September 20-21, 2021; Belgrade (2021):84,
https://hdl.handle.net/21.15107/rcub_vinar_10842 .

TY  - JOUR
AU  - Aleksić, Jelena
AU  - Barudžija, Tanja
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Bošković, Marko
AU  - Jagličić, Zvonko
AU  - Lisjak, Darja
AU  - Kostić, Ljiljana
PY  - 2020
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8858
AB  - In this investigation, we have synthesized YbxY1-xF3 solid solutions by fluorination of yttrium and ytterbium sesquioxides with ammonium hydrogen difluoride. According to the XRD analysis, all synthesized YbxY1-xF3 samples have an orthorhombic crystal structure belonging to the β-YF3 structural type. The refinement of crystal structure was done by the Rietveld method within the Pnma space group using the TCH pseudo-Voigt function. The anisotropic peak broadening was analyzed, and the average apparent crystallite size is about 50 nm with a small anisotropy of shape, while the significant microstrain that is highly anisotropic is present in all samples. The temperature-dependent magnetic susceptibility was analyzed by applying the model of a free ion perturbed by the crystal field. We have obtained the effective magnetic quantum numbers Mieff of four Kramer's doublets of Yb3+ ion along with the entire crystal field splitting of the 2F7/2 manifold of Yb3+ in YF3. The acquired maximum energy splitting of the ground level is about 150 K in our most diluted samples. The field-dependent isothermal magnetization measurements were carried out at various temperatures and analyzed by classical Langevin function. Results obtained from magnetic measurements show that all YbxY1-xF3 (x ≠ 0) solid solutions exhibit pure paramagnetic behavior in the whole temperature range from 2 to 300 K, with a predominant antiferromagnetic exchange interactions. © 2020 Elsevier Ltd
T2  - Journal of Physics and Chemistry of Solids
T1  - Investigation of structural, microstructural and magnetic properties of YbxY1-xF3 solid solutions
VL  - 142
SP  - 109449
DO  - 10.1016/j.jpcs.2020.109449
ER  - 

@article{
author = "Aleksić, Jelena and Barudžija, Tanja and Jugović, Dragana and Mitrić, Miodrag and Bošković, Marko and Jagličić, Zvonko and Lisjak, Darja and Kostić, Ljiljana",
year = "2020",
abstract = "In this investigation, we have synthesized YbxY1-xF3 solid solutions by fluorination of yttrium and ytterbium sesquioxides with ammonium hydrogen difluoride. According to the XRD analysis, all synthesized YbxY1-xF3 samples have an orthorhombic crystal structure belonging to the β-YF3 structural type. The refinement of crystal structure was done by the Rietveld method within the Pnma space group using the TCH pseudo-Voigt function. The anisotropic peak broadening was analyzed, and the average apparent crystallite size is about 50 nm with a small anisotropy of shape, while the significant microstrain that is highly anisotropic is present in all samples. The temperature-dependent magnetic susceptibility was analyzed by applying the model of a free ion perturbed by the crystal field. We have obtained the effective magnetic quantum numbers Mieff of four Kramer's doublets of Yb3+ ion along with the entire crystal field splitting of the 2F7/2 manifold of Yb3+ in YF3. The acquired maximum energy splitting of the ground level is about 150 K in our most diluted samples. The field-dependent isothermal magnetization measurements were carried out at various temperatures and analyzed by classical Langevin function. Results obtained from magnetic measurements show that all YbxY1-xF3 (x ≠ 0) solid solutions exhibit pure paramagnetic behavior in the whole temperature range from 2 to 300 K, with a predominant antiferromagnetic exchange interactions. © 2020 Elsevier Ltd",
journal = "Journal of Physics and Chemistry of Solids",
title = "Investigation of structural, microstructural and magnetic properties of YbxY1-xF3 solid solutions",
volume = "142",
pages = "109449",
doi = "10.1016/j.jpcs.2020.109449"
}

Aleksić, J., Barudžija, T., Jugović, D., Mitrić, M., Bošković, M., Jagličić, Z., Lisjak, D.,& Kostić, L.. (2020). Investigation of structural, microstructural and magnetic properties of YbxY1-xF3 solid solutions. in Journal of Physics and Chemistry of Solids, 142, 109449.
https://doi.org/10.1016/j.jpcs.2020.109449

Aleksić J, Barudžija T, Jugović D, Mitrić M, Bošković M, Jagličić Z, Lisjak D, Kostić L. Investigation of structural, microstructural and magnetic properties of YbxY1-xF3 solid solutions. in Journal of Physics and Chemistry of Solids. 2020;142:109449.
doi:10.1016/j.jpcs.2020.109449 .

Aleksić, Jelena, Barudžija, Tanja, Jugović, Dragana, Mitrić, Miodrag, Bošković, Marko, Jagličić, Zvonko, Lisjak, Darja, Kostić, Ljiljana, "Investigation of structural, microstructural and magnetic properties of YbxY1-xF3 solid solutions" in Journal of Physics and Chemistry of Solids, 142 (2020):109449,
https://doi.org/10.1016/j.jpcs.2020.109449 . .

TY  - JOUR
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Milović, Miloš
AU  - Ivanovski, Valentin N.
AU  - Škapin, Srečo Davor
AU  - Dojčinović, Biljana P.
AU  - Uskoković, Dragan
PY  - 2019
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8047
AB  - A new method involving the homogeneous dispersion of precursor compounds inside a methylcellulose matrix is used for the synthesis of a composite powder of Li 2 FeP 2 O 7 and carbon. The properties of carbon-containing and carbon-free powders are studied by X-ray powder diffraction (XRD) including Rietveld refinement, Mössbauer spectroscopy, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), galvanostatic cycling, and electrochemical impedance spectroscopy (EIS). The structure of both powders is refined in a monoclinic framework (space group P2 1 /c). The structural refinement and Mössbauer spectroscopy reveal different degrees of partial occupancy of mixed-occupied sites by lithium. Electrochemical measurements show that the in situ formation of carbon improves capacity (90% of 1-electron theoretical capacity) through decreased charge-transfer resistance. © 2019 Elsevier B.V.
T2  - Journal of Alloys and Compounds
T1  - Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose
VL  - 786
SP  - 912
EP  - 919
DO  - 10.1016/j.jallcom.2019.01.392
ER  - 

@article{
author = "Jugović, Dragana and Mitrić, Miodrag and Milović, Miloš and Ivanovski, Valentin N. and Škapin, Srečo Davor and Dojčinović, Biljana P. and Uskoković, Dragan",
year = "2019",
abstract = "A new method involving the homogeneous dispersion of precursor compounds inside a methylcellulose matrix is used for the synthesis of a composite powder of Li 2 FeP 2 O 7 and carbon. The properties of carbon-containing and carbon-free powders are studied by X-ray powder diffraction (XRD) including Rietveld refinement, Mössbauer spectroscopy, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), galvanostatic cycling, and electrochemical impedance spectroscopy (EIS). The structure of both powders is refined in a monoclinic framework (space group P2 1 /c). The structural refinement and Mössbauer spectroscopy reveal different degrees of partial occupancy of mixed-occupied sites by lithium. Electrochemical measurements show that the in situ formation of carbon improves capacity (90% of 1-electron theoretical capacity) through decreased charge-transfer resistance. © 2019 Elsevier B.V.",
journal = "Journal of Alloys and Compounds",
title = "Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose",
volume = "786",
pages = "912-919",
doi = "10.1016/j.jallcom.2019.01.392"
}

Jugović, D., Mitrić, M., Milović, M., Ivanovski, V. N., Škapin, S. D., Dojčinović, B. P.,& Uskoković, D.. (2019). Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose. in Journal of Alloys and Compounds, 786, 912-919.
https://doi.org/10.1016/j.jallcom.2019.01.392

Jugović D, Mitrić M, Milović M, Ivanovski VN, Škapin SD, Dojčinović BP, Uskoković D. Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose. in Journal of Alloys and Compounds. 2019;786:912-919.
doi:10.1016/j.jallcom.2019.01.392 .

Jugović, Dragana, Mitrić, Miodrag, Milović, Miloš, Ivanovski, Valentin N., Škapin, Srečo Davor, Dojčinović, Biljana P., Uskoković, Dragan, "Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose" in Journal of Alloys and Compounds, 786 (2019):912-919,
https://doi.org/10.1016/j.jallcom.2019.01.392 . .

TY  - JOUR
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Milović, Miloš
AU  - Ivanovski, Valentin N.
AU  - Škapin, Srečo Davor
AU  - Dojčinović, Biljana P.
AU  - Uskoković, Dragan
PY  - 2019
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8052
AB  - A new method involving the homogeneous dispersion of precursor compounds inside a methylcellulose matrix is used for the synthesis of a composite powder of Li 2 FeP 2 O 7 and carbon. The properties of carbon-containing and carbon-free powders are studied by X-ray powder diffraction (XRD) including Rietveld refinement, Mössbauer spectroscopy, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), galvanostatic cycling, and electrochemical impedance spectroscopy (EIS). The structure of both powders is refined in a monoclinic framework (space group P2 1 /c). The structural refinement and Mössbauer spectroscopy reveal different degrees of partial occupancy of mixed-occupied sites by lithium. Electrochemical measurements show that the in situ formation of carbon improves capacity (90% of 1-electron theoretical capacity) through decreased charge-transfer resistance. © 2019 Elsevier B.V.
T2  - Journal of Alloys and Compounds
T1  - Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose
VL  - 786
SP  - 912
EP  - 919
DO  - 10.1016/j.jallcom.2019.01.392
ER  - 

@article{
author = "Jugović, Dragana and Mitrić, Miodrag and Milović, Miloš and Ivanovski, Valentin N. and Škapin, Srečo Davor and Dojčinović, Biljana P. and Uskoković, Dragan",
year = "2019",
abstract = "A new method involving the homogeneous dispersion of precursor compounds inside a methylcellulose matrix is used for the synthesis of a composite powder of Li 2 FeP 2 O 7 and carbon. The properties of carbon-containing and carbon-free powders are studied by X-ray powder diffraction (XRD) including Rietveld refinement, Mössbauer spectroscopy, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), galvanostatic cycling, and electrochemical impedance spectroscopy (EIS). The structure of both powders is refined in a monoclinic framework (space group P2 1 /c). The structural refinement and Mössbauer spectroscopy reveal different degrees of partial occupancy of mixed-occupied sites by lithium. Electrochemical measurements show that the in situ formation of carbon improves capacity (90% of 1-electron theoretical capacity) through decreased charge-transfer resistance. © 2019 Elsevier B.V.",
journal = "Journal of Alloys and Compounds",
title = "Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose",
volume = "786",
pages = "912-919",
doi = "10.1016/j.jallcom.2019.01.392"
}

Jugović, D., Mitrić, M., Milović, M., Ivanovski, V. N., Škapin, S. D., Dojčinović, B. P.,& Uskoković, D.. (2019). Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose. in Journal of Alloys and Compounds, 786, 912-919.
https://doi.org/10.1016/j.jallcom.2019.01.392

Jugović D, Mitrić M, Milović M, Ivanovski VN, Škapin SD, Dojčinović BP, Uskoković D. Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose. in Journal of Alloys and Compounds. 2019;786:912-919.
doi:10.1016/j.jallcom.2019.01.392 .

Jugović, Dragana, Mitrić, Miodrag, Milović, Miloš, Ivanovski, Valentin N., Škapin, Srečo Davor, Dojčinović, Biljana P., Uskoković, Dragan, "Structural and electrochemical properties of the Li2FeP2O7/C composite prepared using soluble methylcellulose" in Journal of Alloys and Compounds, 786 (2019):912-919,
https://doi.org/10.1016/j.jallcom.2019.01.392 . .

TY  - JOUR
AU  - Jugović, Dragana
AU  - Milović, Miloš
AU  - Popović, Maja
AU  - Kusigerski, Vladan
AU  - Škapin, Srečo Davor
AU  - Rakočević, Zlatko Lj.
AU  - Mitrić, Miodrag
PY  - 2019
UR  - https://linkinghub.elsevier.com/retrieve/pii/S0925838818336375
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7897
AB  - The main goal of this research has been to investigate for the first time the effects of fluorination on the crystal structure, magnetic, and electrochemical properties of the P2-type NaxCoO2 powder. Sodium cobalt oxide with a P2-type structure is synthesized by a modified solid-state reaction consisting of alternating processes of rapid heating up to 750 °C and rapid cooling to the room temperature. The obtained powder is fluorinated using a gas-solid reaction with NH4HF2 as fluorinating agent. Fluorination causes a decrease of sodium content in the parent phase with the concurrent formation of the minor phases of Na2CO3 and NaF. The structure of NaxCoO2 in both powders is refined in P63/mmc space group. The results of the Rietveld refinement combined with the findings from the XPS measurements confirm the Na0.76CoO2 and Na0.44CoO1.96F0.04 stoichiometries for the pristine and fluorinated powders, respectively, which indicates that 4 at.% of fluorine ions per formula unit are incorporated in the structure. Preliminary electrochemical investigations have revealed an improved charge/discharge performance. The influence of fluorination on morphology and magnetic properties has also been examined. © 2018 Elsevier B.V.
T2  - Journal of Alloys and Compounds
T1  - Effects of fluorination on the structure, magnetic and electrochemical properties of the P2-type NaxCoO2 powder
VL  - 774
SP  - 30
EP  - 37
DO  - 10.1016/j.jallcom.2018.09.372
ER  - 

@article{
author = "Jugović, Dragana and Milović, Miloš and Popović, Maja and Kusigerski, Vladan and Škapin, Srečo Davor and Rakočević, Zlatko Lj. and Mitrić, Miodrag",
year = "2019",
abstract = "The main goal of this research has been to investigate for the first time the effects of fluorination on the crystal structure, magnetic, and electrochemical properties of the P2-type NaxCoO2 powder. Sodium cobalt oxide with a P2-type structure is synthesized by a modified solid-state reaction consisting of alternating processes of rapid heating up to 750 °C and rapid cooling to the room temperature. The obtained powder is fluorinated using a gas-solid reaction with NH4HF2 as fluorinating agent. Fluorination causes a decrease of sodium content in the parent phase with the concurrent formation of the minor phases of Na2CO3 and NaF. The structure of NaxCoO2 in both powders is refined in P63/mmc space group. The results of the Rietveld refinement combined with the findings from the XPS measurements confirm the Na0.76CoO2 and Na0.44CoO1.96F0.04 stoichiometries for the pristine and fluorinated powders, respectively, which indicates that 4 at.% of fluorine ions per formula unit are incorporated in the structure. Preliminary electrochemical investigations have revealed an improved charge/discharge performance. The influence of fluorination on morphology and magnetic properties has also been examined. © 2018 Elsevier B.V.",
journal = "Journal of Alloys and Compounds",
title = "Effects of fluorination on the structure, magnetic and electrochemical properties of the P2-type NaxCoO2 powder",
volume = "774",
pages = "30-37",
doi = "10.1016/j.jallcom.2018.09.372"
}

Jugović, D., Milović, M., Popović, M., Kusigerski, V., Škapin, S. D., Rakočević, Z. Lj.,& Mitrić, M.. (2019). Effects of fluorination on the structure, magnetic and electrochemical properties of the P2-type NaxCoO2 powder. in Journal of Alloys and Compounds, 774, 30-37.
https://doi.org/10.1016/j.jallcom.2018.09.372

Jugović D, Milović M, Popović M, Kusigerski V, Škapin SD, Rakočević ZL, Mitrić M. Effects of fluorination on the structure, magnetic and electrochemical properties of the P2-type NaxCoO2 powder. in Journal of Alloys and Compounds. 2019;774:30-37.
doi:10.1016/j.jallcom.2018.09.372 .

Jugović, Dragana, Milović, Miloš, Popović, Maja, Kusigerski, Vladan, Škapin, Srečo Davor, Rakočević, Zlatko Lj., Mitrić, Miodrag, "Effects of fluorination on the structure, magnetic and electrochemical properties of the P2-type NaxCoO2 powder" in Journal of Alloys and Compounds, 774 (2019):30-37,
https://doi.org/10.1016/j.jallcom.2018.09.372 . .

TY  - JOUR
AU  - Georgijević, Radovan
AU  - Vujković, Milica
AU  - Gutić, Sanjin J.
AU  - Aliefendić, Meho
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Đokić, Veljko R.
AU  - Mentus, Slavko V.
PY  - 2019
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7936
AB  - To contribute to the knowledge on the influence of synthesis procedure on the intercalation kinetics of lithium ions into phospho-olivines, LiFePO4/C composite samples (LFPC) were synthesized in two ways, the first one in a sol-gel procedure (SG), and the other in a solid-state reaction (SS). The X-ray diffractograms (XRD) of both samples overlapped with that of pure LiFePO4, taken from the crystallographic database. Scanning electron microscopy pictures indicated the high degree of interparticle sintering, which caused a considerable agglomerate growth. The results of potentiodynamic measurements in aqueous LiNO3 solution revealed that for SS sample, three times higher initial capacity from that of SG one, (amounting to 74 mAh g−1 at 5 mV s−1). However, capacity fade on rising scan rate is much more expressed for SS sample than for SG one. We suggest that a different degree of material utilization due to the incomplete coverage of olivine particles by carbon explains this difference. The technique of separation of diffusion and capacitance currents was applied in a kinetic analysis, but it was shown to be inappropriate. We suggest the inapplicability of classic CV theory to the intercalation system accompanied by phase transition. Instead, a model of ohmic resistance determination of process kinetics was considered. LFPC-SS sample delivers three times larger capacity in LiNO3, amounting to 74 mAh g−1 at 1 mV s−1.
T2  - Journal of Alloys and Compounds
T1  - The influence of synthesis conditions on the redox behaviour of LiFePO4 in aqueous solution
VL  - 776
SP  - 475
EP  - 485
DO  - 10.1016/j.jallcom.2018.10.246
ER  - 

@article{
author = "Georgijević, Radovan and Vujković, Milica and Gutić, Sanjin J. and Aliefendić, Meho and Jugović, Dragana and Mitrić, Miodrag and Đokić, Veljko R. and Mentus, Slavko V.",
year = "2019",
abstract = "To contribute to the knowledge on the influence of synthesis procedure on the intercalation kinetics of lithium ions into phospho-olivines, LiFePO4/C composite samples (LFPC) were synthesized in two ways, the first one in a sol-gel procedure (SG), and the other in a solid-state reaction (SS). The X-ray diffractograms (XRD) of both samples overlapped with that of pure LiFePO4, taken from the crystallographic database. Scanning electron microscopy pictures indicated the high degree of interparticle sintering, which caused a considerable agglomerate growth. The results of potentiodynamic measurements in aqueous LiNO3 solution revealed that for SS sample, three times higher initial capacity from that of SG one, (amounting to 74 mAh g−1 at 5 mV s−1). However, capacity fade on rising scan rate is much more expressed for SS sample than for SG one. We suggest that a different degree of material utilization due to the incomplete coverage of olivine particles by carbon explains this difference. The technique of separation of diffusion and capacitance currents was applied in a kinetic analysis, but it was shown to be inappropriate. We suggest the inapplicability of classic CV theory to the intercalation system accompanied by phase transition. Instead, a model of ohmic resistance determination of process kinetics was considered. LFPC-SS sample delivers three times larger capacity in LiNO3, amounting to 74 mAh g−1 at 1 mV s−1.",
journal = "Journal of Alloys and Compounds",
title = "The influence of synthesis conditions on the redox behaviour of LiFePO4 in aqueous solution",
volume = "776",
pages = "475-485",
doi = "10.1016/j.jallcom.2018.10.246"
}

Georgijević, R., Vujković, M., Gutić, S. J., Aliefendić, M., Jugović, D., Mitrić, M., Đokić, V. R.,& Mentus, S. V.. (2019). The influence of synthesis conditions on the redox behaviour of LiFePO4 in aqueous solution. in Journal of Alloys and Compounds, 776, 475-485.
https://doi.org/10.1016/j.jallcom.2018.10.246

Georgijević R, Vujković M, Gutić SJ, Aliefendić M, Jugović D, Mitrić M, Đokić VR, Mentus SV. The influence of synthesis conditions on the redox behaviour of LiFePO4 in aqueous solution. in Journal of Alloys and Compounds. 2019;776:475-485.
doi:10.1016/j.jallcom.2018.10.246 .

Georgijević, Radovan, Vujković, Milica, Gutić, Sanjin J., Aliefendić, Meho, Jugović, Dragana, Mitrić, Miodrag, Đokić, Veljko R., Mentus, Slavko V., "The influence of synthesis conditions on the redox behaviour of LiFePO4 in aqueous solution" in Journal of Alloys and Compounds, 776 (2019):475-485,
https://doi.org/10.1016/j.jallcom.2018.10.246 . .

TY  - JOUR
AU  - Milović, Miloš
AU  - Vasić Anićijević, Dragana D.
AU  - Jugović, Dragana
AU  - Anićijević, Vladan J.
AU  - Veselinović, Ljiljana M.
AU  - Mitrić, Miodrag
AU  - Uskoković, Dragan
PY  - 2019
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8017
AB  - Li2FeSiO4 material, which was prepared by a solid state method, crystallized as monoclinic P21/n polymorph. X-ray diffraction analysis with Rietveld structural refinement indicates specific occupation of Li2 crystallographic site by Fe2+ cation in the amount of 6 atom percents as a result of an antisite defect formation. The exclusive occupation of Li2 position, out of two crystallographic positions Li1 and Li2, by Fe2+ was discussed in relation to the differences that exist in the crystal environment of these positions and further investigated by DFT calculations. It was confirmed that Fe-Li2 substitution is energetically favorable compared to both Fe-Li1 substitution and the pristine crystal. In addition, changes of lattice geometry upon antisite defect formation were analyzed, and the obtained result is discussed in light of various factors (electronic, geometrical and enthropic) that contribute to the overall stability of the system. © 2018 Elsevier Masson SAS
T2  - Solid State Sciences
T1  - On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study
VL  - 87
SP  - 81
EP  - 86
DO  - 10.1016/j.solidstatesciences.2018.11.008
ER  - 

@article{
author = "Milović, Miloš and Vasić Anićijević, Dragana D. and Jugović, Dragana and Anićijević, Vladan J. and Veselinović, Ljiljana M. and Mitrić, Miodrag and Uskoković, Dragan",
year = "2019",
abstract = "Li2FeSiO4 material, which was prepared by a solid state method, crystallized as monoclinic P21/n polymorph. X-ray diffraction analysis with Rietveld structural refinement indicates specific occupation of Li2 crystallographic site by Fe2+ cation in the amount of 6 atom percents as a result of an antisite defect formation. The exclusive occupation of Li2 position, out of two crystallographic positions Li1 and Li2, by Fe2+ was discussed in relation to the differences that exist in the crystal environment of these positions and further investigated by DFT calculations. It was confirmed that Fe-Li2 substitution is energetically favorable compared to both Fe-Li1 substitution and the pristine crystal. In addition, changes of lattice geometry upon antisite defect formation were analyzed, and the obtained result is discussed in light of various factors (electronic, geometrical and enthropic) that contribute to the overall stability of the system. © 2018 Elsevier Masson SAS",
journal = "Solid State Sciences",
title = "On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study",
volume = "87",
pages = "81-86",
doi = "10.1016/j.solidstatesciences.2018.11.008"
}

Milović, M., Vasić Anićijević, D. D., Jugović, D., Anićijević, V. J., Veselinović, L. M., Mitrić, M.,& Uskoković, D.. (2019). On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study. in Solid State Sciences, 87, 81-86.
https://doi.org/10.1016/j.solidstatesciences.2018.11.008

Milović M, Vasić Anićijević DD, Jugović D, Anićijević VJ, Veselinović LM, Mitrić M, Uskoković D. On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study. in Solid State Sciences. 2019;87:81-86.
doi:10.1016/j.solidstatesciences.2018.11.008 .

Milović, Miloš, Vasić Anićijević, Dragana D., Jugović, Dragana, Anićijević, Vladan J., Veselinović, Ljiljana M., Mitrić, Miodrag, Uskoković, Dragan, "On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study" in Solid State Sciences, 87 (2019):81-86,
https://doi.org/10.1016/j.solidstatesciences.2018.11.008 . .

TY  - JOUR
AU  - Milović, Miloš
AU  - Vasić Anićijević, Dragana D.
AU  - Jugović, Dragana
AU  - Anićijević, Vladan J.
AU  - Veselinović, Ljiljana M.
AU  - Mitrić, Miodrag
AU  - Uskoković, Dragan
PY  - 2019
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8021
AB  - Li2FeSiO4 material, which was prepared by a solid state method, crystallized as monoclinic P21/n polymorph. X-ray diffraction analysis with Rietveld structural refinement indicates specific occupation of Li2 crystallographic site by Fe2+ cation in the amount of 6 atom percents as a result of an antisite defect formation. The exclusive occupation of Li2 position, out of two crystallographic positions Li1 and Li2, by Fe2+ was discussed in relation to the differences that exist in the crystal environment of these positions and further investigated by DFT calculations. It was confirmed that Fe-Li2 substitution is energetically favorable compared to both Fe-Li1 substitution and the pristine crystal. In addition, changes of lattice geometry upon antisite defect formation were analyzed, and the obtained result is discussed in light of various factors (electronic, geometrical and enthropic) that contribute to the overall stability of the system. © 2018 Elsevier Masson SAS
T2  - Solid State Sciences
T1  - On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study
VL  - 87
SP  - 81
EP  - 86
DO  - 10.1016/j.solidstatesciences.2018.11.008
ER  - 

@article{
author = "Milović, Miloš and Vasić Anićijević, Dragana D. and Jugović, Dragana and Anićijević, Vladan J. and Veselinović, Ljiljana M. and Mitrić, Miodrag and Uskoković, Dragan",
year = "2019",
abstract = "Li2FeSiO4 material, which was prepared by a solid state method, crystallized as monoclinic P21/n polymorph. X-ray diffraction analysis with Rietveld structural refinement indicates specific occupation of Li2 crystallographic site by Fe2+ cation in the amount of 6 atom percents as a result of an antisite defect formation. The exclusive occupation of Li2 position, out of two crystallographic positions Li1 and Li2, by Fe2+ was discussed in relation to the differences that exist in the crystal environment of these positions and further investigated by DFT calculations. It was confirmed that Fe-Li2 substitution is energetically favorable compared to both Fe-Li1 substitution and the pristine crystal. In addition, changes of lattice geometry upon antisite defect formation were analyzed, and the obtained result is discussed in light of various factors (electronic, geometrical and enthropic) that contribute to the overall stability of the system. © 2018 Elsevier Masson SAS",
journal = "Solid State Sciences",
title = "On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study",
volume = "87",
pages = "81-86",
doi = "10.1016/j.solidstatesciences.2018.11.008"
}

Milović, M., Vasić Anićijević, D. D., Jugović, D., Anićijević, V. J., Veselinović, L. M., Mitrić, M.,& Uskoković, D.. (2019). On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study. in Solid State Sciences, 87, 81-86.
https://doi.org/10.1016/j.solidstatesciences.2018.11.008

Milović M, Vasić Anićijević DD, Jugović D, Anićijević VJ, Veselinović LM, Mitrić M, Uskoković D. On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study. in Solid State Sciences. 2019;87:81-86.
doi:10.1016/j.solidstatesciences.2018.11.008 .

Milović, Miloš, Vasić Anićijević, Dragana D., Jugović, Dragana, Anićijević, Vladan J., Veselinović, Ljiljana M., Mitrić, Miodrag, Uskoković, Dragan, "On the presence of antisite defect in monoclinic Li2FeSiO4 – A combined X-Ray diffraction and DFT study" in Solid State Sciences, 87 (2019):81-86,
https://doi.org/10.1016/j.solidstatesciences.2018.11.008 . .

TY  - CONF
AU  - Rakočević, Lazar
AU  - Novaković, Mirjana M.
AU  - Potočnik, Jelena
AU  - Jugović, Dragana
AU  - Stojković-Simatović, Ivana
PY  - 2018
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/8734
AB  - Due to the increasing use of batteries in everyday life and in industry, there is a need for developing cheaper batteries than the widely used lithium ion batteries. Lower price and higher abundance of sodium compared to lithium mineral resources intensified the development of Na-ion batteries. Aqueous lithium/ sodium rechargeable batteries have attracted considerable attention for energy storage because they do not contain flammable organic electrolytes as commercial batteries do, the ionic conductivity of the aqueous electrolyte is about two orders of magnitude higher than in non-aqueous electrolyte and the electrolyte salt and solvent are cheaper. Various materials such as manganese oxides, vanadium oxide and phosphates have been used as electrode materials (cathodic and anodic) in sodium batteries due to high sodium intercalation ability in both, organic and aqueous electrolytes. The most frequently used type of manganese oxides are Li–Mn–O or Na–Mn–O systems due to their tunnel or layered crystal structures which facilitate the lithium/sodium intercalation-deintercalation. In this work, a glycine-nitrate method (GNM) was applied for the synthesis of cathode material Na0.4MnO2.
PB  - Belgrade : Serbian Academy of Sciences and Arts
C3  - Program and Book of Abstracts / First International Conference on Electron Microscopy of Nanostructures ELMINA 2018, August 27-29, 2018, Belgrade, Serbia
T1  - Synthesis and Characterization of Na0.4MnO2 as a Positive Electrode Material for an Aqueous Electrolyte Sodium-ion Energy Storage Device
SP  - 154
EP  - 156
UR  - https://hdl.handle.net/21.15107/rcub_vinar_8734
ER  - 

@conference{
author = "Rakočević, Lazar and Novaković, Mirjana M. and Potočnik, Jelena and Jugović, Dragana and Stojković-Simatović, Ivana",
year = "2018",
abstract = "Due to the increasing use of batteries in everyday life and in industry, there is a need for developing cheaper batteries than the widely used lithium ion batteries. Lower price and higher abundance of sodium compared to lithium mineral resources intensified the development of Na-ion batteries. Aqueous lithium/ sodium rechargeable batteries have attracted considerable attention for energy storage because they do not contain flammable organic electrolytes as commercial batteries do, the ionic conductivity of the aqueous electrolyte is about two orders of magnitude higher than in non-aqueous electrolyte and the electrolyte salt and solvent are cheaper. Various materials such as manganese oxides, vanadium oxide and phosphates have been used as electrode materials (cathodic and anodic) in sodium batteries due to high sodium intercalation ability in both, organic and aqueous electrolytes. The most frequently used type of manganese oxides are Li–Mn–O or Na–Mn–O systems due to their tunnel or layered crystal structures which facilitate the lithium/sodium intercalation-deintercalation. In this work, a glycine-nitrate method (GNM) was applied for the synthesis of cathode material Na0.4MnO2.",
publisher = "Belgrade : Serbian Academy of Sciences and Arts",
journal = "Program and Book of Abstracts / First International Conference on Electron Microscopy of Nanostructures ELMINA 2018, August 27-29, 2018, Belgrade, Serbia",
title = "Synthesis and Characterization of Na0.4MnO2 as a Positive Electrode Material for an Aqueous Electrolyte Sodium-ion Energy Storage Device",
pages = "154-156",
url = "https://hdl.handle.net/21.15107/rcub_vinar_8734"
}

Rakočević, L., Novaković, M. M., Potočnik, J., Jugović, D.,& Stojković-Simatović, I.. (2018). Synthesis and Characterization of Na0.4MnO2 as a Positive Electrode Material for an Aqueous Electrolyte Sodium-ion Energy Storage Device. in Program and Book of Abstracts / First International Conference on Electron Microscopy of Nanostructures ELMINA 2018, August 27-29, 2018, Belgrade, Serbia
Belgrade : Serbian Academy of Sciences and Arts., 154-156.
https://hdl.handle.net/21.15107/rcub_vinar_8734

Rakočević L, Novaković MM, Potočnik J, Jugović D, Stojković-Simatović I. Synthesis and Characterization of Na0.4MnO2 as a Positive Electrode Material for an Aqueous Electrolyte Sodium-ion Energy Storage Device. in Program and Book of Abstracts / First International Conference on Electron Microscopy of Nanostructures ELMINA 2018, August 27-29, 2018, Belgrade, Serbia. 2018;:154-156.
https://hdl.handle.net/21.15107/rcub_vinar_8734 .

Rakočević, Lazar, Novaković, Mirjana M., Potočnik, Jelena, Jugović, Dragana, Stojković-Simatović, Ivana, "Synthesis and Characterization of Na0.4MnO2 as a Positive Electrode Material for an Aqueous Electrolyte Sodium-ion Energy Storage Device" in Program and Book of Abstracts / First International Conference on Electron Microscopy of Nanostructures ELMINA 2018, August 27-29, 2018, Belgrade, Serbia (2018):154-156,
https://hdl.handle.net/21.15107/rcub_vinar_8734 .

TY  - CONF
AU  - Jugović, Dragana
AU  - Milović, Miloš
AU  - Mitrić, Miodrag
AU  - Cvjetićanin, Nikola
AU  - Škapin, Srečo Davor
AU  - Uskoković, Dragan
PY  - 2017
UR  - http://dais.sanu.ac.rs/123456789/15439
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7560
AB  - The search for alternative cathode materials for Li-ion batteries has recently emerged Li2FeP2O7 pyrophosphate as a new potential competitor for LiFePO4 material. It has a possibility to offer good rate capability, lithium ion diffusivity and volumetric energy density, and is a material of high safety and low raw materials cost. In addition, there is the probability of releasing the second Li-atom at a higher redox potential of 5.2 V, where the theoretical capacity would reach 220 mAhg−1. Optimized solid state reaction is used for the synthesis of pure Li2FeP2O7 powder and a composite Li2FeP2O7/C. The synthesized powders are characterized by X-ray powder diffraction, field emission scanning electron microscopy, FTIR spectroscopy, and galvanostatic charge/discharge cycling.
PB  - Belgrade : Materials Research Society of Serbia
C3  - Programme and The Book of Abstracts / Nineteenth Annual Conference YUCOMAT 2017, Herceg Novi, September 4-8, 2017
T1  - Synthesis and characterization of Li2FeP2O7 cathode material
SP  - 46
EP  - 46
UR  - https://hdl.handle.net/21.15107/rcub_vinar_7560
ER  - 

@conference{
editor = "Uskoković, Dragan, Radmilović, Velimir R.",
author = "Jugović, Dragana and Milović, Miloš and Mitrić, Miodrag and Cvjetićanin, Nikola and Škapin, Srečo Davor and Uskoković, Dragan",
year = "2017",
abstract = "The search for alternative cathode materials for Li-ion batteries has recently emerged Li2FeP2O7 pyrophosphate as a new potential competitor for LiFePO4 material. It has a possibility to offer good rate capability, lithium ion diffusivity and volumetric energy density, and is a material of high safety and low raw materials cost. In addition, there is the probability of releasing the second Li-atom at a higher redox potential of 5.2 V, where the theoretical capacity would reach 220 mAhg−1. Optimized solid state reaction is used for the synthesis of pure Li2FeP2O7 powder and a composite Li2FeP2O7/C. The synthesized powders are characterized by X-ray powder diffraction, field emission scanning electron microscopy, FTIR spectroscopy, and galvanostatic charge/discharge cycling.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "Programme and The Book of Abstracts / Nineteenth Annual Conference YUCOMAT 2017, Herceg Novi, September 4-8, 2017",
title = "Synthesis and characterization of Li2FeP2O7 cathode material",
pages = "46-46",
url = "https://hdl.handle.net/21.15107/rcub_vinar_7560"
}

Uskoković, D., Radmilović, V. R., Jugović, D., Milović, M., Mitrić, M., Cvjetićanin, N., Škapin, S. D.,& Uskoković, D.. (2017). Synthesis and characterization of Li2FeP2O7 cathode material. in Programme and The Book of Abstracts / Nineteenth Annual Conference YUCOMAT 2017, Herceg Novi, September 4-8, 2017
Belgrade : Materials Research Society of Serbia., 46-46.
https://hdl.handle.net/21.15107/rcub_vinar_7560

Uskoković D, Radmilović VR, Jugović D, Milović M, Mitrić M, Cvjetićanin N, Škapin SD, Uskoković D. Synthesis and characterization of Li2FeP2O7 cathode material. in Programme and The Book of Abstracts / Nineteenth Annual Conference YUCOMAT 2017, Herceg Novi, September 4-8, 2017. 2017;:46-46.
https://hdl.handle.net/21.15107/rcub_vinar_7560 .

Uskoković, Dragan, Radmilović, Velimir R., Jugović, Dragana, Milović, Miloš, Mitrić, Miodrag, Cvjetićanin, Nikola, Škapin, Srečo Davor, Uskoković, Dragan, "Synthesis and characterization of Li2FeP2O7 cathode material" in Programme and The Book of Abstracts / Nineteenth Annual Conference YUCOMAT 2017, Herceg Novi, September 4-8, 2017 (2017):46-46,
https://hdl.handle.net/21.15107/rcub_vinar_7560 .

TY  - CONF
AU  - Aleksić, Jelena
AU  - Jugović, Dragana
AU  - Milović, Miloš
AU  - Mitrić, Miodrag
AU  - Uskoković, Dragan
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7564
AB  - Sodium transition-metal oxides with general formula NaxTMO2 (TM = Co, Mn, Ni, etc.) have attracted a lot of interest in the battery community due to low cost of sodium in contrast to lithium. Sodium cobalt oxide is the most attractive of them for cathode application because of its conductive, thermic and magnetic characteristics. In this study, sodium cobalt oxide, NaxCoO2 , was synthesized by simple method which involves solid state reaction in air, at temperature of 900 ºC; starting materials were Na2CO3 and Co3O4 in stoichiometric amounts. Additionally, fluorination of the synthesized sodium cobalt oxide was carried out in vacuum at 200ºC; NH4HF2 was used as a fluorine source. Then, structural and microstructural properties of the obtained powders were examined.
PB  - Belgrade : Institute of Technical Sciences of SASA
C3  - Program and the Book of Abstracts / Sixteenth Young Researchers' Conference Materials Sciences and Engineering, December 6-8, 2017, Belgrade, Serbia
T1  - Synthesis and structural properties of sodium cobalt oxide
SP  - 37
EP  - 37
UR  - https://hdl.handle.net/21.15107/rcub_vinar_7564
ER  - 

@conference{
editor = "Marković, Smilja",
author = "Aleksić, Jelena and Jugović, Dragana and Milović, Miloš and Mitrić, Miodrag and Uskoković, Dragan",
year = "2017",
abstract = "Sodium transition-metal oxides with general formula NaxTMO2 (TM = Co, Mn, Ni, etc.) have attracted a lot of interest in the battery community due to low cost of sodium in contrast to lithium. Sodium cobalt oxide is the most attractive of them for cathode application because of its conductive, thermic and magnetic characteristics. In this study, sodium cobalt oxide, NaxCoO2 , was synthesized by simple method which involves solid state reaction in air, at temperature of 900 ºC; starting materials were Na2CO3 and Co3O4 in stoichiometric amounts. Additionally, fluorination of the synthesized sodium cobalt oxide was carried out in vacuum at 200ºC; NH4HF2 was used as a fluorine source. Then, structural and microstructural properties of the obtained powders were examined.",
publisher = "Belgrade : Institute of Technical Sciences of SASA",
journal = "Program and the Book of Abstracts / Sixteenth Young Researchers' Conference Materials Sciences and Engineering, December 6-8, 2017, Belgrade, Serbia",
title = "Synthesis and structural properties of sodium cobalt oxide",
pages = "37-37",
url = "https://hdl.handle.net/21.15107/rcub_vinar_7564"
}

Marković, S., Aleksić, J., Jugović, D., Milović, M., Mitrić, M.,& Uskoković, D.. (2017). Synthesis and structural properties of sodium cobalt oxide. in Program and the Book of Abstracts / Sixteenth Young Researchers' Conference Materials Sciences and Engineering, December 6-8, 2017, Belgrade, Serbia
Belgrade : Institute of Technical Sciences of SASA., 37-37.
https://hdl.handle.net/21.15107/rcub_vinar_7564

Marković S, Aleksić J, Jugović D, Milović M, Mitrić M, Uskoković D. Synthesis and structural properties of sodium cobalt oxide. in Program and the Book of Abstracts / Sixteenth Young Researchers' Conference Materials Sciences and Engineering, December 6-8, 2017, Belgrade, Serbia. 2017;:37-37.
https://hdl.handle.net/21.15107/rcub_vinar_7564 .

Marković, Smilja, Aleksić, Jelena, Jugović, Dragana, Milović, Miloš, Mitrić, Miodrag, Uskoković, Dragan, "Synthesis and structural properties of sodium cobalt oxide" in Program and the Book of Abstracts / Sixteenth Young Researchers' Conference Materials Sciences and Engineering, December 6-8, 2017, Belgrade, Serbia (2017):37-37,
https://hdl.handle.net/21.15107/rcub_vinar_7564 .

TY  - JOUR
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Milović, Miloš
AU  - Cvjetićanin, Nikola
AU  - Jokić, Bojan M.
AU  - Umićević, Ana
AU  - Uskoković, Dragan
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1401
AB  - Low intrinsic electronic conductivity is the main disadvantage of LiFePO4 when used as a cathode material in lithium ion batteries. The paper offers experimental proofs of the theoretical prediction that fluorine doping of LiFePO4 can enhance its electrical conductivity. The LiFePO4 and fluorine-doped LiFePO4 olivine type, carbon free powders are synthesized and examined. The crystal structure refinements in the Pnma space group reveal that doping with fluorine ions preserves the olivine structure, while reducing both the lattice parameters and the antisite defect, and increasing the crystallite size. A small amount of incorporated fluorine enhances the electrical conductivity from 4.6x10(-7) S cm(-1) to 2.3x10(-6) S cm(-1) and has a positive impact on the electrochemical performance. Several spectroscopy techniques (Mossbauer, FTIR, and Raman) reveal differences between the two powders and additionally support the findings of both the Rietveld refinement and the conductivity measurements.
T2  - Ceramics International
T1  - The influence of fluorine doping on the structural and electrical properties of the LiFePO4 powder
VL  - 43
IS  - 3
SP  - 3224
EP  - 3230
DO  - 10.1016/j.ceramint.2016.11.149
ER  - 

@article{
author = "Jugović, Dragana and Mitrić, Miodrag and Milović, Miloš and Cvjetićanin, Nikola and Jokić, Bojan M. and Umićević, Ana and Uskoković, Dragan",
year = "2017",
abstract = "Low intrinsic electronic conductivity is the main disadvantage of LiFePO4 when used as a cathode material in lithium ion batteries. The paper offers experimental proofs of the theoretical prediction that fluorine doping of LiFePO4 can enhance its electrical conductivity. The LiFePO4 and fluorine-doped LiFePO4 olivine type, carbon free powders are synthesized and examined. The crystal structure refinements in the Pnma space group reveal that doping with fluorine ions preserves the olivine structure, while reducing both the lattice parameters and the antisite defect, and increasing the crystallite size. A small amount of incorporated fluorine enhances the electrical conductivity from 4.6x10(-7) S cm(-1) to 2.3x10(-6) S cm(-1) and has a positive impact on the electrochemical performance. Several spectroscopy techniques (Mossbauer, FTIR, and Raman) reveal differences between the two powders and additionally support the findings of both the Rietveld refinement and the conductivity measurements.",
journal = "Ceramics International",
title = "The influence of fluorine doping on the structural and electrical properties of the LiFePO4 powder",
volume = "43",
number = "3",
pages = "3224-3230",
doi = "10.1016/j.ceramint.2016.11.149"
}

Jugović, D., Mitrić, M., Milović, M., Cvjetićanin, N., Jokić, B. M., Umićević, A.,& Uskoković, D.. (2017). The influence of fluorine doping on the structural and electrical properties of the LiFePO4 powder. in Ceramics International, 43(3), 3224-3230.
https://doi.org/10.1016/j.ceramint.2016.11.149

Jugović D, Mitrić M, Milović M, Cvjetićanin N, Jokić BM, Umićević A, Uskoković D. The influence of fluorine doping on the structural and electrical properties of the LiFePO4 powder. in Ceramics International. 2017;43(3):3224-3230.
doi:10.1016/j.ceramint.2016.11.149 .

Jugović, Dragana, Mitrić, Miodrag, Milović, Miloš, Cvjetićanin, Nikola, Jokić, Bojan M., Umićević, Ana, Uskoković, Dragan, "The influence of fluorine doping on the structural and electrical properties of the LiFePO4 powder" in Ceramics International, 43, no. 3 (2017):3224-3230,
https://doi.org/10.1016/j.ceramint.2016.11.149 . .

TY  - JOUR
AU  - Bratić, Milan
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Cvjetićanin, Nikola
PY  - 2017
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/1585
AB  - Anatase TiO2 nanotube arrays of different morphology were prepared by a two-step process: anodic oxidation at voltages 20-60 V and subsequent annealing at 400 degrees C. By amplifying anodization voltage the inner diameter of nanotubes increased. At 60 V nanotubes changed the shape from cylindrical tube to truncated cone with elliptical opening. Electrochemical insertion of Li-ion in nanotubes was studied by cyclic voltammetry and galvanostatic charge-discharge experiments. The cyclovoltammetric response was fast for all nanotube arrays. The galvanostatic areal charge/discharge capacity of nanotube arrays increased with increasing anodizaton voltage. Although the mass of nanotubes prepared at 45 V was larger, the gravimetrical capacity was much higher for nanotubes prepared at 60 V because of the larger surface area exposed to the electrolyte. Gravimetrical capacity values exceed theoretical bulk capacity of anatase due to the surface storage of Li-ion. Diffusion coefficient of Li-ion was calculated to be between 5.9.10(-16) and 5.9.10(-15) cm(2) s(-1). (C) 2017 Elsevier B.V. All rights reserved.
T2  - Journal of Alloys and Compounds
T1  - Insertion of lithium ion in anatase TiO2 nanotube arrays of different morphology
VL  - 712
SP  - 90
EP  - 96
DO  - 10.1016/j.jallcom.2017.04.065
ER  - 

@article{
author = "Bratić, Milan and Jugović, Dragana and Mitrić, Miodrag and Cvjetićanin, Nikola",
year = "2017",
abstract = "Anatase TiO2 nanotube arrays of different morphology were prepared by a two-step process: anodic oxidation at voltages 20-60 V and subsequent annealing at 400 degrees C. By amplifying anodization voltage the inner diameter of nanotubes increased. At 60 V nanotubes changed the shape from cylindrical tube to truncated cone with elliptical opening. Electrochemical insertion of Li-ion in nanotubes was studied by cyclic voltammetry and galvanostatic charge-discharge experiments. The cyclovoltammetric response was fast for all nanotube arrays. The galvanostatic areal charge/discharge capacity of nanotube arrays increased with increasing anodizaton voltage. Although the mass of nanotubes prepared at 45 V was larger, the gravimetrical capacity was much higher for nanotubes prepared at 60 V because of the larger surface area exposed to the electrolyte. Gravimetrical capacity values exceed theoretical bulk capacity of anatase due to the surface storage of Li-ion. Diffusion coefficient of Li-ion was calculated to be between 5.9.10(-16) and 5.9.10(-15) cm(2) s(-1). (C) 2017 Elsevier B.V. All rights reserved.",
journal = "Journal of Alloys and Compounds",
title = "Insertion of lithium ion in anatase TiO2 nanotube arrays of different morphology",
volume = "712",
pages = "90-96",
doi = "10.1016/j.jallcom.2017.04.065"
}

Bratić, M., Jugović, D., Mitrić, M.,& Cvjetićanin, N.. (2017). Insertion of lithium ion in anatase TiO2 nanotube arrays of different morphology. in Journal of Alloys and Compounds, 712, 90-96.
https://doi.org/10.1016/j.jallcom.2017.04.065

Bratić M, Jugović D, Mitrić M, Cvjetićanin N. Insertion of lithium ion in anatase TiO2 nanotube arrays of different morphology. in Journal of Alloys and Compounds. 2017;712:90-96.
doi:10.1016/j.jallcom.2017.04.065 .

Bratić, Milan, Jugović, Dragana, Mitrić, Miodrag, Cvjetićanin, Nikola, "Insertion of lithium ion in anatase TiO2 nanotube arrays of different morphology" in Journal of Alloys and Compounds, 712 (2017):90-96,
https://doi.org/10.1016/j.jallcom.2017.04.065 . .

TY  - CONF
AU  - Jugović, Dragana
AU  - Bradarić, Ivica
AU  - Jovalekić, Čedomir
AU  - Barudžija, Tanja
AU  - Kusigerski, Vladan
AU  - Mitrić, Miodrag
PY  - 2016
UR  - http://dais.sanu.ac.rs/123456789/897
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7554
AB  - Perovskite oxides with the composition LaFe1-xCrxO3 (x = 0.5 and 0.75) have been studied. The samples have been prepared using the mechanochemical treatment. A mixture of crystalline La(OH)3, Fe2O3 and Cr2O3 powders in stoichiometric ratio was mechanochemically treated in a planetary ball mill up to 40 h of milling. The mechanochemical formation of the LaFe1-xCrxO3 perovskite phase was followed by X-ray diffraction and magnetization measurements. The Rietveld refinement of the XRD data shows that the compounds crystallize in an orthorhombic perovskite structure with a random distribution of the Fe and Cr cations at the B sublattice. All structural and microstructural parameters were analyzed. In addition, magnetic measurements for LaFe0.5Cr0.5O3 show clear antiferromagnetic ordering bellow 250 K, which supports above conclusion of random distribution of Fe and Cr cations.
PB  - Belgrade : Materials Research Society of Serbia
C3  - YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi
T1  - Structural and magnetic properties of mechanochemically synthesized LaFe1-xCrxO3 (x = 0.5 and 0.75)
SP  - 57
EP  - 57
UR  - https://hdl.handle.net/21.15107/rcub_vinar_7554
ER  - 

@conference{
author = "Jugović, Dragana and Bradarić, Ivica and Jovalekić, Čedomir and Barudžija, Tanja and Kusigerski, Vladan and Mitrić, Miodrag",
year = "2016",
abstract = "Perovskite oxides with the composition LaFe1-xCrxO3 (x = 0.5 and 0.75) have been studied. The samples have been prepared using the mechanochemical treatment. A mixture of crystalline La(OH)3, Fe2O3 and Cr2O3 powders in stoichiometric ratio was mechanochemically treated in a planetary ball mill up to 40 h of milling. The mechanochemical formation of the LaFe1-xCrxO3 perovskite phase was followed by X-ray diffraction and magnetization measurements. The Rietveld refinement of the XRD data shows that the compounds crystallize in an orthorhombic perovskite structure with a random distribution of the Fe and Cr cations at the B sublattice. All structural and microstructural parameters were analyzed. In addition, magnetic measurements for LaFe0.5Cr0.5O3 show clear antiferromagnetic ordering bellow 250 K, which supports above conclusion of random distribution of Fe and Cr cations.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi",
title = "Structural and magnetic properties of mechanochemically synthesized LaFe1-xCrxO3 (x = 0.5 and 0.75)",
pages = "57-57",
url = "https://hdl.handle.net/21.15107/rcub_vinar_7554"
}

Jugović, D., Bradarić, I., Jovalekić, Č., Barudžija, T., Kusigerski, V.,& Mitrić, M.. (2016). Structural and magnetic properties of mechanochemically synthesized LaFe1-xCrxO3 (x = 0.5 and 0.75). in YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi
Belgrade : Materials Research Society of Serbia., 57-57.
https://hdl.handle.net/21.15107/rcub_vinar_7554

Jugović D, Bradarić I, Jovalekić Č, Barudžija T, Kusigerski V, Mitrić M. Structural and magnetic properties of mechanochemically synthesized LaFe1-xCrxO3 (x = 0.5 and 0.75). in YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi. 2016;:57-57.
https://hdl.handle.net/21.15107/rcub_vinar_7554 .

Jugović, Dragana, Bradarić, Ivica, Jovalekić, Čedomir, Barudžija, Tanja, Kusigerski, Vladan, Mitrić, Miodrag, "Structural and magnetic properties of mechanochemically synthesized LaFe1-xCrxO3 (x = 0.5 and 0.75)" in YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi (2016):57-57,
https://hdl.handle.net/21.15107/rcub_vinar_7554 .

TY  - CONF
AU  - Jugović, Dragana
AU  - Mitrić, Miodrag
AU  - Milović, Miloš
AU  - Cvjetićanin, Nikola
AU  - Jokić, Bojan M.
AU  - Umićević, Ana
AU  - Uskoković, Dragan
PY  - 2016
UR  - http://dais.sanu.ac.rs/123456789/898
UR  - https://vinar.vin.bg.ac.rs/handle/123456789/7555
AB  - Low intrinsic electronic conductivity is the main weakness of LiFePO4 for the use as cathode material in lithium ion batteries. Here is presented an experimental proof of the theoretical prediction that fluorine doping of LiFePO4 can enhance its electrical conductivity. LiFePO4 and fluorine-doped LiFePO4 olivine type, carbon-free powders are synthesized and examined. Crystal structure refinements in the space group Pnma reveal that doping with fluorine ions preserves olivine structure with the reduction of both the lattice parameters and the antisite defect, and an increase of a crystallite size. A small amount of incorporated fluorine enhances electrical conductivity from 4.6 × 10-7 Scm-1 to 2.3 × 10-6 Scm-1 and has positive impact on the electrochemical performances. Several spectroscopy techniques (Mössbauer, FTIR, and Raman) disclose differences between two powders and additionally support the findings of both the Rietveld refinement and the conductivity measurements.
PB  - Belgrade : Materials Research Society of Serbia
C3  - YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi
T1  - The influence of fluorine doping on the structural and the electrical properties of LiFePO4 powder
SP  - 35
EP  - 35
UR  - https://hdl.handle.net/21.15107/rcub_vinar_7555
ER  - 

@conference{
author = "Jugović, Dragana and Mitrić, Miodrag and Milović, Miloš and Cvjetićanin, Nikola and Jokić, Bojan M. and Umićević, Ana and Uskoković, Dragan",
year = "2016",
abstract = "Low intrinsic electronic conductivity is the main weakness of LiFePO4 for the use as cathode material in lithium ion batteries. Here is presented an experimental proof of the theoretical prediction that fluorine doping of LiFePO4 can enhance its electrical conductivity. LiFePO4 and fluorine-doped LiFePO4 olivine type, carbon-free powders are synthesized and examined. Crystal structure refinements in the space group Pnma reveal that doping with fluorine ions preserves olivine structure with the reduction of both the lattice parameters and the antisite defect, and an increase of a crystallite size. A small amount of incorporated fluorine enhances electrical conductivity from 4.6 × 10-7 Scm-1 to 2.3 × 10-6 Scm-1 and has positive impact on the electrochemical performances. Several spectroscopy techniques (Mössbauer, FTIR, and Raman) disclose differences between two powders and additionally support the findings of both the Rietveld refinement and the conductivity measurements.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi",
title = "The influence of fluorine doping on the structural and the electrical properties of LiFePO4 powder",
pages = "35-35",
url = "https://hdl.handle.net/21.15107/rcub_vinar_7555"
}

Jugović, D., Mitrić, M., Milović, M., Cvjetićanin, N., Jokić, B. M., Umićević, A.,& Uskoković, D.. (2016). The influence of fluorine doping on the structural and the electrical properties of LiFePO4 powder. in YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi
Belgrade : Materials Research Society of Serbia., 35-35.
https://hdl.handle.net/21.15107/rcub_vinar_7555

Jugović D, Mitrić M, Milović M, Cvjetićanin N, Jokić BM, Umićević A, Uskoković D. The influence of fluorine doping on the structural and the electrical properties of LiFePO4 powder. in YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi. 2016;:35-35.
https://hdl.handle.net/21.15107/rcub_vinar_7555 .

Jugović, Dragana, Mitrić, Miodrag, Milović, Miloš, Cvjetićanin, Nikola, Jokić, Bojan M., Umićević, Ana, Uskoković, Dragan, "The influence of fluorine doping on the structural and the electrical properties of LiFePO4 powder" in YUCOMAT 2016 : 18th Annual Conference YUCOMAT 2016 : programme and the book of abstracts; September 5-10, Herceg Novi (2016):35-35,
https://hdl.handle.net/21.15107/rcub_vinar_7555 .